BOBBER SOLO SEAT KITS
J066812018-04-09
GENERAL
Kit Number
Mounting Kits
Rigid Kit: 52100043
Spring Kit: 52100029
Seat Kits
52000314, 52000315, 52000320, 52000381
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
These kits require the separate purchase of Spring Kit (52100029).
NOTE
An optional Rigid Kit (52100043) is also available, but still require purchase of Spring Kit (52100029). Replace springs with rigid mounts.
Kit Contents
See Figure 5 and Table 1.
INSTALLATION
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
NOTE
When a solo seat is installed without a passenger seat, the passenger foot pegs or foot boards and the passenger grab strap must be removed.
When removing or installing the seat, do not scratch painted surfaces (fender, tank, and so on) with metal tab on seat.
1.
Remove original equipment (OE) seat. See service manual.
2.
See Figure 1. Remove the six screws from under seat location.
Figure 1. Bolt Removal
3.
See Figure 1 and Figure 5. Install front mounting bracket (13). Secure with screws (7) to front of bracket and screws (5) to rear of bracket. Tighten.
Torque: 10.8–13.5 N·m (8–10 ft-lbs) Screw (7)
Torque: 9.4–12.2 N·m (7–9 ft-lbs) Screw (5)
4.
Install right and left mounting perch (15,16). Secure with screws (9). Tighten.
Torque: 23–27 N·m (17–20 ft-lbs)
5.
Spring Kit:
5.1.
See Figure 3 and Figure 5. Place one washer (8) inside top (tighter coil end) of spring (4) and one washer (8) outside top of spring, assemble on screw (6). See Figure 2. Attach assembly to holes, location (A), on bottom of seat. Tighten
Torque: 13.55 N·m (120 in-lbs)
b.
Attached spring grommet (12) to bottom of spring.
c.
Attach bracket (17) to under seat cover (3) with screw (18) and nut (19). Tighten.
Torque: 7.45 N·m (66 in-lbs)
d.
Repeat steps (a,b,c) for other side.
e.
Place under seat cover (3) on right and left mounting perch (15,16).
f.
Secure front of under seat cover (3) to front mounting bracket (13) with two screws (18).
g.
Ensure two bushings (11) are in place within the nose of the mounting bracket.
h.
Align clevis bracket (14), in an upright position, to front mounting bracket (13). Secure with screw (10). Tighten.
Torque: 8.5 N·m (75 in-lbs)
i.
See Figure 4 and Figure 5. Mount seat pan (1) to clevis bracket (14) using two screws (2). Tighten.
Torque: 8.13–9.49 N·m (72–84 in-lbs)
ASpring kit location
BRigid kit location
Figure 2. Kit Attachment Location
6.
NOTE
Spring (4) may need to adjusted to fit over right and left mounting perch (15,16).
Rigid Kit:
a.
See Figure 3. Assemble rigid mount post (20) to seat pan (1). Tighten.
Torque: 13.55 N·m (120 in-lbs)
b.
See Figure 4 and Figure 5. Mount seat pan (1) to clevis bracket (14) using two screws (2). Tighten.
Torque: 8.13–9.49 N·m (72–84 in-lbs)
c.
Align rear of seat pan (1) over right and left mounting perch (15,16).
d.
Assemble screw (10) to clevis bracket (14). Tighten.
Torque: 8.47 N·m (75 in-lbs)
Figure 3. Springs/Rigids being attached to Seat
Figure 4. Seat Assembly Installed to Vehicle
7.
After installing seat, pull up on the front of seat to verify that it is secure. See service manual.
SERVICE PARTS
Figure 5. Service Parts: Solo Seat Kits
Table 1. Service Parts: Solo Seat Kits
Kit
Item
Description (Quantity)
Part Number
52000314
1
Seat, smooth leather with trim ring
Not sold separately
52000315
Seat, tuck and roll
Not sold separately
52000320
Seat, black distressed, no foam
Not sold separately
52000381
Seat, brown distressed, no foam
Not sold separately
2
Screw (2)
10200660
52100029
3
Under seat cover
52000363
4
Springs (2)
52100054
5
Screw, hex socket button head (2)
924
6
Screw, hex socket cap (2)
3275
7
Screw, hex socket button head (2)
4015
8
Washer (4)
6116
9
Screw, hex socket head cap (2)
94335-91T
10
Screw, shoulder
10200605
11
Bushing (2)
11000115
12
Grommet (2)
12100116
13
Bracket, front mounting
52100032
14
Clevis bracket
52100034
15
Mounting perch, right
52100037
16
Mounting perch, left
52100038
17
Bracket (2)
Not sold separately
18
Screw (4)
4365
19
Nut (2)
7688
52100043
12
Grommet (2)
12100116
20
Mounting post (2)
52100041