BOOM! PREMIUM RADIO INFOTAINMENT KIT
J066492018-08-22
GENERAL
Dealer installation is recommended.
Kit Number
76000829, 76000834
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
Radio configuration using DIGITAL TECHNICIAN II (Part Number:HD-48650) diagnostic tool is:
  • Required before audio system OPERATION. System will beep every 3 seconds until configuration is completed.
  • Only available through authorized Harley-Davidson dealers.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
Kit Contents
See Figure 5 and Table 1.
REMOVAL
See service manual for specific instructions on this generalized procedure.
WARNING
To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
1.
Remove main fuse.
2.
Remove outer fairing.
3.
Fork-Mounted Faring: Remove fairing vent and instrument cluster.
4.
Remove upper support bracket.
4.1.
Fork-Mounted Faring: See Figure 1. Remove screws (1, 2, 3, 6).
1Upper support-to-speaker enclosure screw (4)
2Upper support-to-inner fairing screw (2)
3Upper support-to-radio screw (4)
4Upper support bracket
5Instrument cluster
6Media compartment screw
Figure 1. Fork-Mounted Upper Support Bracket
4.2.
Frame-Mounted Faring: See Figure 2. Remove screws (1).
1Screw (2)
2Upper support bracket
Figure 2. Frame-Mounted Upper Support Bracket
5.
See Figure 3. Disconnect connectors (2-5).
6.
Remove four screws (1).
1Screw, radio mounting (4)
2GPS (Global positioning system) connector
3AM/FM connector
4USB (Universal serial bus) connector
5Radio harness connector
Figure 3. Radio Connectors
7.
Pull radio up and forward to remove.
INSTALLATION
1.
See Figure 5. Install radio (1).
a.
Position radio on fairing support brackets and push toward opening in inner fairing.
2.
See Figure 3. Install four screws (1).
Torque: 6.8–9.5 N·m (60–84 in-lbs) Radio mounting screw
3.
Fork-Mounted Faring: Install instrument cluster.
4.
Fork-Mounted Faring: See Figure 1. Install upper support bracket.
a.
Install screws (2). Tighten.
Torque: 1.1–2.2 N·m (10–19 in-lbs)
b.
Install screws (1). Tighten.
Torque: 5.4–6.8 N·m (48–60 in-lbs)
c.
Install screws (3). Tighten.
Torque: 2.8–4 N·m (25–35 in-lbs)
d.
Install screw (6). Tighten.
Torque: 2.8–4 N·m (25–35 in-lbs)
5.
Frame-Mounted Faring: See Figure 2. Install upper support bracket.
a.
Install screw (1). Tighten.
Torque: 2.8–4 N·m (25–35 in-lbs)
6.
See Figure 4. Install GPS antenna.
a.
Clean top of upper support bracket with isopropyl alcohol. Allow to dry completely.
b.
Remove adhesive backing from antenna.
c.
With the wire lead toward the right, press and hold antenna (2) for 60 seconds.
NOTE
After installing antenna, avoid contact or movement of the antenna for 20 minutes.
7.
Secure antenna lead to harness with cable strap (1).
8.
See Figure 3. Connect connectors (2-5).
1Cable strap
2GPS antenna
3Connector
Figure 4. GPS Antenna
SWITCH CAP
1.
NOTE
See the service manual of the year and model vehicle that the service is being performed on for the following steps.
Remove front right hand control cover.
2.
Remove right turn signal and info switch cap.
3.
See Figure 5. Install new switch cap (2).
4.
Install front right hand control cover.
COMPLETE
NOTE
To prevent possible damage to the audio system, verify that the ignition is OFF before installing the main fuse.
1.
Fork-Mounted Faring: Install fairing vent.
2.
Install outer fairing.
3.
Install main fuse.
4.
Update radio software. See Harley-Davidson.com
a.
Follow instructions on website.
5.
NOTE
DT II (Digital technician) will configure the radio and amplifiers all at the same time.
Have Harley-Davidson dealer configure the radio using DT II.

Special Tool: DIGITAL TECHNICIAN II (HD-48650)

6.
NOTE
To download a PDF (Portable document format ) of the Harley Davidson International (HDI) or Rest of World (ROW) Boom! Box owner's manual, see Harley-Davidson.com or https://serviceinfo.harley-davidson.com.
Refer to BOOM! BOX 6.5 GTS owner's manual.
a.
Turn radio ON.
b.
Make sure that all speakers are working properly.
c.
Make sure front/rear fader function is operating correctly.
7.
Verify all turn signals functions are working properly.
SERVICE PARTS
Figure 5. Service Parts, Boom! Premium Radio Infotainment Kit
Table 1. Service Parts
Item
Description
Part Number
1
Premium Radio Infotainment Kit, (DOM)
Fork Mounted Fairing
76000829
Frame Mounted Fairing
76000834
2
Switch cap
71500478
3
GPS antenna
76000789
4
Boom! Box 6.5 GTS Owner's Manual (Not shown)
94000601
5
Boom! Box 6.5 GTS Quick Start Guide (Not shown)
94000634