TOMAHAWK FRONT WHEELS
J066652018-08-20
GENERAL
WARNING
Install only wheels and installation kits approved for your model motorcycle. Contact a Harley-Davidson dealer to verify fitment. Mismatching wheels and installation kits or installing wheels not approved for your model can cause loss of control, which could result in death or serious injury. (00610c)
Kit Numbers
43300641 and 43300642
Models
For model fitment information, see the P&A Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
NOTE
Accessory hub caps are not compatible with this wheel style.
Kit Contents
These kits include the custom wheel only. See Table 1 for kit contents.
Installation Requirements
Proper installation of this kit requires the separate purchase of the following parts which are available at a Harley-Davidson dealer:
  • Wheel Installation Kit (See Table 2 and Table 3 to determine required installation kit.)
  • If the customer already owns two front brake disks (41500017), then only 2 chrome brake disc screw kits (41500095) (includes 5 screws, washers, and bushings) are required.
  • Two polished brake rotor kits 41500094 (bolts & mounting hardware included) only if the customer doesn't already have polished rotors (41500094) or stock rotors (41500017).
  • Wheel Bearing Remover and Installer (94134-09A)
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
Recommended Products
The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning:
  • Chrome Clean & Shine (93600031 (US) / 93600082 (International))
  • Glaze Poly Sealant (93600026 (US) / 93600079 (International))
  • Harley® Wheel and Spoke Brush (43078-99)
  • Wheel & Tire Cleaner (93600024 (US) / 93600076 (International))
INSTALLATION
1.
Remove existing front wheel assembly. Save axle, axle nut and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual.
NOTE
Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems.
2.
See Figure 1. Install valve stem assembly (L) on wheel. Refer to TIRES in service manual.
NOTE
Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER.
The side with the DOT marking is the primary bearing side.
The bearing shims provided in the installation kits are not required and can be discarded.
NOTICE
Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c)
3.
Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual.
4.
Install previously removed wheel spacers. Refer to FRONT WHEEL in service manual.
5.
Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual.
MAINTENANCE AND CLEANING
Chrome parts must be maintained regularly to verify that they keep their original shine and luster.
  1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush.
  2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner.
  3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant.
SERVICE PARTS
Figure 1. Service Parts: Aggressor Front Wheel Kits
Table 1. Service Parts and Wheel Kit Contents
Kit
Item
Description (Quantity)
Part Number
43300641 and 43300642
1
Wheel
Not Sold Separately
Table 2. FRONT 25 mm Bearing Wheel Installation Kit (41455-08C)
FRONT 25 mm Bearing Wheel Installation Kit (41455-08C)
ITEM (Quantity Used and Description)
Fitment
Wheel Size
A
D
L
M
N
2014 and later Touring (non-ABS)
19 x 3.5 in
2
1
*
*
*
Installation kits are designed to work with many different wheel styles and fitments.
Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on.
NOTE:
*See NOTE above valve installation step in INSTALLATION to determine which valve stem to use for your particular kit. Discard other valve stem(s).
A
Bearing, regular (2)
9276A
D
Axle sleeve
41900-08
L
Valve stem, short
43157-83A
M
Valve stem, long
43206-01
N
Valve stem, pull thru
40999-87
Table 3. FRONT 25 mm Bearing ABS Wheel Installation Kit (41454-08B)
FRONT 25 mm Bearing ABS Wheel
Installation Kit (41454-08B)
ITEM (Quantity Used and Description)
Fitment
Wheel Size
A
B
D
L
M
N
2014 and later Touring with ABS
19 x 3.5 in
1
1
1
*
*
*
Installation kits are designed to work with many different wheel styles and A Bearing, regular 9276A fitments. Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on.
NOTES:
*See NOTE above valve installation step in INSTALLATION to determine which valve stem to use for your particular kit. Discard other valve stem(s).
**Red side of bearing must be installed toward the wheel. The ABS bearing is primary.
A
Bearing, regular
9276A
B
Bearing, ABS**
9252
D
Axle sleeve
41900-08
L
Valve stem, short
43157-83A
M
Valve stem, long
43206-01
N
Valve stem, pull thru
40999-87