Heel/Toe Shift Lever Kits
J026072018-08-21
GENERAL
Kit Number
34023-08, 34535-00B, 34558-05A, 34045-10, 33600076, 33600255
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) is required for the proper installation of this kit.
Kit Contents
See Figure 1 and Table 1.
REMOVAL
NOTE
  • Before removing the original shift levers, note the orientation. You may want to replace them at the same position and angle.
  • OE (Original equipment) shift levers are installed from the top or bottom, depending on the model motorcycle.
1.
See Figure 1. Remove OE shifter pegs (A) and retain for installation to new levers if desired.
2.
Remove socket head screws (3).
3.
Remove OE shift levers.
INSTALLATION
1.
Position toe shifter lever (1) at the desired angle and so the counterbored screw hole is facing down.
NOTE
When toe and heel levers are positioned correctly, the socket head cap screws are installed from the bottom of both levers.
2.
Slide toe shifter lever onto splined shifter shaft.
3.
Align screw hole with notch on shaft.
4.
Position heel shifter lever (2) at the desired angle and so the counterbored screw hole is facing down.
5.
Slide heel shifter lever onto splined shifter shaft, Aligning screw hole with notch on shaft.
6.
Apply threadlocker to socket head screws (3).
LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
7.
Insert screws into counterbored holes. Tighten.
Torque: 32–35 N·m (24–26 ft-lbs) Socket head screw
NOTE
For proper installation, ensure that the toe and heel shifter are completely installed on shifter shaft and applied torque meets but does not exceed given range.
8.
Apply threadlocker onto shifter peg screw threads if using OE pegs.
LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
9.
Install shifter pegs onto new shift levers. Tighten.
Torque: 11–16.4 N·m (97–145 in-lbs) Shifter peg screw
10.
Check for proper operation and clearance.
SERVICE PARTS
Figure 1. Service Parts: Shift Lever Kit (Generic Shown)
Table 1. Service Parts Table
Kit
Item
Description (Quantity)
Part Number
Kit 34023-08
Billet (black)
1
Toe shift lever (black)
Not sold separately
2
Heel shift lever (black)
Not sold separately
3
Hex socket head cap screw (2)
94332-91T
Kit 34535-00B
Billet (chrome)
1
Toe shift lever (chrome)
Not sold separately
2
Heel shift lever (chrome)
Not sold separately
3
Hex socket head cap screw (2)
94332-91T
Kit 34558-05A
Buckshot
1
Toe shift lever
33742-05A
2
Heel shift lever
33747-07
3
Hex socket head cap screw (2)
94332-91T
Kit 34045-10
Edge cut
1
Toe shift lever
Not sold separately
2
Heel shift lever
Not sold separately
3
Hex socket head cap screw (2)
94332-91T
Kit 33600076
Airflow
1
Toe shift lever
33600060
2
Heel shift lever
33600061
3
Hex socket head cap screw (2)
3275
Kit 33600255
Airflow (black)
1
Toe shift lever
33600225
2
Heel shift lever
33600227
3
Hex socket head cap screw (2)
3275
Items mentioned in text, but not included in kit:
A
Shifter peg (2)
B
Front of motorcycle