RIDER & PASSENGER FOOTPEG KIT
J065052017-08-22
GENERAL
Kit Number
    Edge Cut: 50500851, 50500857, 50500967, 50501020
    Willie G: 50500856, 50500858
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer.
Kit Contents
See Figure 4 and Table 1.
INSTALLATION
RIDER
1.
See Figure 2. Your model motorcycle is equipped with a pin (4) and retaining clip (2), remove them and retain for future use. Save all hardware, including torsion spring (1), for installation of the new footpegs (3).
Figure 1. Torsion Spring
2.
See Figure 2. Insert short leg of torsion spring (1) into hole in new footpeg (3). Align long leg of torsion spring (1) to hole in footpeg mount and insert. Rotate footpeg (3) into position in clevis and insert pin (4) through clevis, footpeg (3) and spring (1). Install retaining clip (2). Repeat on other side.
NOTE
See Figure 1. When performing the next step, verify that the spring is positioned inside of the footpeg.
3.
Willie G Rider Pegs (Only)- adjust orientation as follows:
a.
For forward controls, foot surface to be parallel to the mounting pin.
b.
For mid controls, foot surface to be parallel to ground.
c.
Tighten adjustment screw.
Torque: 28.5 N·m (21 ft-lbs)
1Torsion spring
2Retaining clip
3Footpeg
4Pin
Figure 2. Rider Footpeg Torsion Spring Installation
PASSENGER
1.
See Figure 3. Your model motorcycle is equipped with a pin (1) and retaining clip (5). Remove them and retain for future use. Save all hardware, including detent spring (3), detent ball (4) and cage (6) for installation of the new footpegs (2).
2.
Insert detent spring (3) into new footpeg (2), followed by detent ball (4). Position cage (6) on footpeg clevis edge while capturing the detent ball (4) and detent spring (3) inside cage (6) while sliding cage (6) onto footpeg clevis.
NOTE
See Figure 3. When performing the next step, verify that the spring (3) is positioned inside of the footpeg (2).
3.
Align cage (6) and footpeg (2) with footpeg mount on vehicle.
4.
Install pin (1) and retaining clip (5).
5.
Willie G Passenger Pegs (only) - adjust orientation as follows:
a.
Rotate to desired orientation.
b.
Fold peg up to stowed position and confirm clearance to other components. Adjust as necessary.
c.
Tighten adjustment screw.
Torque: 28.5 N·m (21 ft-lbs)
1Pin
2Footpeg
3Detent spring
4Detent ball
5Retaining clip
6Cage
Figure 3. Passenger Footpeg Detent Ball Installation
WARNING
Footrests must fold up and toward rear of motorcycle if struck. Failure to set footrests to fold up and back could result in death or serious injury. (00366a)
SERVICE PARTS
Figure 4. Service Parts: Footpeg Kit
Table 1. Service Parts Table
Kit
Item
Description (Quantity)
Part Number
50500967
1
Rider, Edge Cut foot peg, RH
Not Sold Separately
2
Rider, Edge Cut foot peg, LH
Not Sold Separately
3
Rings (6)
11306
4
Wear Peg (2)
50500972
5
N/A
N/A
50500851
1
Rider, Edge Cut foot peg (2)
Not Sold Separately
2
N\A
N\A
3
Rings (6)
11306
4
N/A
N/A
5
N\A
N\A
50500857
1
Passenger, Edge Cut, foot peg (2)
Not Sold Separately
2
N\A
N\A
3
Rings (6)
11306
4
N/A
N/A
5
N/A
N/A
50501020
1
Rider, Edge Cut, foot peg (2)
Not Sold Separately
2
N\A
N\A
3
Rings (4)
11306
4
N\A
N\A
5
N\A
N\A
50500856
1
Rider, Willie G skull, foot peg, LH
Not Sold Separately
2
Rider, Willie G skull, foot peg, RH
Not Sold Separately
3
N\A
N\A
4
N\A
N\A
5
Button socket screw (2)
94409-03
80500858
1
Passenger, Willie G skull, foot peg, LH
Not Sold Separately
2
Passenger, Willie G skull, foot peg, RH
Not Sold Separately
3
N\A
N\A
4
N\A
N\A
5
Button socket screw (2)
94409-03