PASSENGER FOOTBOARD INSERT KITS
J033212011-03-04
GENERAL
Kit Numbers
50420-05, 50537-07, 52312-07, 50500090
Models
These kits are used to complete the installation of a Swept Wing Passenger Footboard Kit on specific model motorcycles.
See the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only) for model fitment information and the correct Passenger Footboard Kit and Passenger Footboard Insert Kit part numbers.
Additional Parts Required
Separate purchase of a Swept Wing Passenger Footboard Kit and additional parts may be required for proper installation of this Passenger Footboard Insert Kit on your model motorcycle.
See the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only) for a list of required parts for your model.
Also see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only) for a collection of matching Genuine Motor Accessory grips, pads and pegs that are available. These can be easily installed at the same time as this kit.
Kit Contents
See Figure 2 and Table 1.
INSTALLATION
If replacing an insert or inserts on a vehicle currently equipped with Swept Wing Passenger Footboards:
Existing Footboard Insert Removal
NOTE
Carefully remove the currently installed footboard insert to avoid damage to chrome surfaces.
  1. See Figure 1. Fold the passenger footboard (1) into the UP position.
  2. Loosen, but do not remove the footboard insert setscrew (2).
  3. With the footboard folded DOWN, carefully raise an outside corner of the existing insert with a suitable flat-bladed tool, taking care to avoid damaging the chrome footboard pan.
  4. Continue around the insert, using a second tool if necessary to pry the existing insert (3) from the footboard pan.
  5. If replacing both inserts, repeat for the opposite footboard.
Swept Wing Passenger Footboard Installation
  1. If installing inserts on a vehicle NOT currently equipped with Swept Wing Passenger Footboards:
  • Remove currently installed passenger footboards (if so equipped) per the instructions included with the Swept Wing Passenger Footboard Kit.
  • Remove currently installed passenger footpegs (if so equipped) by removing the socket screw with lockwasher retaining the footpeg support bracket to the rear fork (swingarm) bracket.
  1. Follow the instructions in the Swept Wing Passenger Footboard Kit to install the passenger footboards.
Footboard Insert Installation
  1. ALL applications: Center the two footboard pivot pins.
  2. Use soapy water to moisten the rubber dowel pins and pivot pin slots on the bottom of the new footboard insert.
  3. Place the insert into position with the rubber dowel pins mating the holes in the footboard pan. Firmly press the insert into the footboard until the dowel pins pop into place.
  4. Fold the passenger floorboard UP and tighten the setscrew to secure the insert.
  5. Repeat Steps 3 through 6 for the opposite footboard.
NOTE
Avoid the contact of chrome surfaces with abrasive materials (stones, sand, etc.) as damage will result.
1Footboard
2Insert set screw
3Existing insert
Figure 1. Swept Wing Passenger Footboard
SERVICE PARTS
Figure 2. Service Parts: Swept Wing Passenger Footboard Insert Kits
Table 1. Service Parts Table
Kit
Item
Description (Quantity)
Part Number
Kit 50420-05
Streamliner Passenger
Footboard Insert
1
Passenger footboard insert (Streamliner, left)
Not Sold Separately
2
Passenger footboard insert (Streamliner, right)
Not Sold Separately
Kit 50537-07
Centerline Passenger
Footboard Insert
1
Passenger footboard insert (Centerline, left)
Not Sold Separately
2
Passenger footboard insert (Centerline, right)
Not Sold Separately
Kit 52312-07
Ironside Passenger
Footboard Insert
1
Passenger footboard insert (Ironside, left)
50819-07
2
Passenger footboard insert (Ironside, right)
50823-07
Kit 50500090
Slipstream Passenger
Footboard Insert
1
Passenger footboard insert (Slipstream, left)
5050060
2
Passenger footboard insert (Slipstream, right)
5050061