PASSENGER BACKREST FOR TOUR-PAK
J056932018-08-20
GENERAL
Kit Numbers
52300312, 52300314, 52300316, 52300317, 52300319, 52300334, 52300335, 52300359, 52300360, 52300567, 52300572, 52300574
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
If the accessory circuit connector is already in use, a Switched Circuit Adapter Harness (Part No. 70264-94A) is also required.
2014-2016 Touring Models: Separate purchase of harness extension (Part No. 69200722) is required to locate the accessory circuit connector for the Heated Tour-Pak® Kit 52300317.
2017 and Later Touring Models: Separate purchase of harness extension (Part No. 69201599) is required to locate the accessory circuit connector for the Heated Tour-Pak® Kit 52300317.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
NOTE
This instruction sheet references service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
Kit Contents
ELECTRICAL OVERLOAD
NOTICE
It is possible to overload your vehicle's charging system by adding too many electrical accessories. If the combined electrical accessories operating at any one time consume more electrical current than the vehicle's charging system can produce, the electrical consumption can discharge the battery and cause damage to the vehicle's electrical system. See an authorized Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories or for necessary wiring changes. (00211c)
WARNING
When installing any electrical accessory, be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modified. Exceeding the maximum amperage can lead to electrical failures, which could result in death or serious injury. (00310a)
Heated Tour-Pak Backrest Kit 52300317 requires up to 3.0 A more current from the electrical system.
PREPARATION
WARNING
To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
NOTE
  • For vehicles equipped with security siren: With security fob present, turn ignition switch ON. After system is disarmed, turn ignition switch OFF. IMMEDIATELY remove the main fuse per the service manual.
  • For vehicles WITHOUT security siren: See the service manual to remove the main fuse.
BACKREST INSTALLATION
King Tour-Pak
1.
See Figure 1. Align the three studs on the backrest (1) with the drilled holes in the Tour-Pak lid. Fasten finger-tight with flanged locknuts (2) and flat washers (3) from the kit.
2.
Center and level the backrest on the Tour-Pak lid for best appearance.
3.
Torque the locknuts. Tighten.
Torque: 11.3–14.7 N·m (100–130 in-lbs)
a.
For Kit 52300317: Proceed to Extra Steps for Heated Backrest.
b.
For ALL other kits: Proceed to ALL Installations.
1Backrest
2Flanged locknut (3)
3Flat washer (3)
Figure 1. Mounted Backrest on King Tour-Pak Lid
Extra Steps for Heated Backrest
1.
Open the Tour-Pak lid. Extend the backrest wires to their full length.
2.
Route the backrest wires:
a.
Above the Tour-Pak left speaker pod, up against the Tour-Pak front wall
b.
Down the inboard side of the speaker pod
c.
Behind the lower Tour-Pak pad
d.
Along the main wire bundle heading under the seat
3.
NOTE
Adhesive-backed plastic clip (Part No. 69200342) and cable strap (Part No. 10006) are suggested to secure the harness.
Close the Tour-Pak lid. Verify that the closing lid does not pinch the harness. Secure as needed to make sure that the harness path remains clear of the lid.
4.
See Figure 2. Assemble the Deutsch heated backrest connector. Refer to the service manual for specific information on the following generalized steps.
a.
Insert the rear wire seal (3) into the Deutsch four-way socket housing (4) from the kit.
b.
Insert the red wire lead and terminal (1) into cavity 3.
c.
Insert the black wire lead and terminal (2) into cavity 4.
d.
Install the internal seal (5).
e.
Insert the secondary locking wedge (6).
f.
Insert seal plugs (7) into cavities 1 and 2.
5.
Get the Harness Extension:
a.
2014-2016 Touring Models: (Part No. 69200722, purchased separately). Plug the eight-way Molex connector into the accessory circuit connector [4A] on the electrical panel under the left side cover. Route the four-way Deutsch pin connector to a position under the seat.
b.
2017 and Later Touring Models: (Part No. 69201599, purchased separately). Plug the three-way Molex connector into the accessory circuit connector [325B] on the electrical panel under the right side cover. Route the four-way Deutsch pin connector to a position under the seat.
6.
Route the Deutsch heated backrest connector underneath the seat and connect to the four-way accessory harness extension connector. Stow wires to make sure that they are not damaged by the seat. Proceed to ALL Installations .
1Red wire lead and terminal
2Black wire lead and terminal
3Rear wire seal
4Deutsch four-way socket housing
5Internal seal
6Secondary locking wedge
7Seal plug (2)
Figure 2. Insert Terminals into Deutsch Socket Housing
Chopped Tour-Pak
1.
See Figure 3. Align the three studs on the backrest (1) with the drilled holes in the Tour-Pak lid. Fasten finger-tight with flanged locknuts (2) from the kit.
2.
Center and level the backrest on the Tour-Pak lid for best appearance.
3.
Tighten the locknuts. Tighten.
Torque: 7.9–9 N·m (70–80 in-lbs)
a.
Proceed to ALL Installations
1Backrest
2Flanged locknut (3)
Figure 3. Mounted Backrest on Chopped Tour-Pak Lid
ALL Installations
NOTE
Verify that the ignition switch is OFF before installing the main fuse.
1.
See the service manual to install the main fuse.
2.
Close the Tour-Pak cover. Check for proper backrest alignment.
3.
See the service manual to install the seat.
HEATED BACKREST TEST AND OPERATION
1.
The rocker switch on the left side of the backrest pad controls the heat setting. Turn ignition switch ON. Verify proper operation of heated backrest.
a.
With rocker switch in the center position, the heat to the backrest is OFF.
b.
Press the lower part of the switch in to turn the heat ON at the LOW setting.
c.
Press the upper part of the switch in to turn the heat ON at the HIGH setting.
2.
Turn ignition switch to ACCY. The rocker switch operates in the same way as in the ON position.
3.
Turn ignition switch OFF. The backrest does not provide heat in any rocker switch position.
SERVICE PARTS
Figure 4. Service Parts, King Tour-Pak Backrest Kits 52300312, 52300314, 52300316, 52300317, 52300334, 52300574
Table 1. Service Parts, King Tour-Pak Backrest Kits 52300312, 52300314, 52300316, 52300317, 52300334, 52300574
Item
Description (Quantity)
Part Number
1
Backrest assembly, all kits except 52300317 (includes Items 2-7)
Backrest assembly, kit 52300317 (includes Items 2-13)
Not sold separately
Not sold separately
2
  • Isolation kit, backrest (3)
52300127
3
  • Support bracket, center
52300121
4
  • Support bracket, right
52300122
5
  • Support bracket, left
52300123
6
  • Flange nut, locking, 5/16"-18 (3) (not shown)
7531
7
  • Washer, flat, 5/16" nominal (3) (not shown)
6026
Items included only in kit 52300317:
8
  • Deutsch socket connector housing, four-way (shown on Figure 2)
72134-94GY
9
  • Deutsch secondary lock (shown on Figure 2)
72154-94
10
  • Deutsch socket terminal (2) (shown on Figure 2)
72191-94
11
  • Deutsch seal pin (2) (shown on Figure 2)
72195-94
12
  • Harness, heated backrest
Not sold separately
13
  • Switch, heated backrest
Not sold separately
Figure 5. Service Parts, Chopped Tour-Pak Backrest Kits 52300319, 52300335, 52300567, 52300572
Table 2. Service Parts, Chopped Tour-Pak Backrest Kits 52300319, 52300335, 52300567, 52300572
Item
Description (Quantity)
Part Number
1
Backrest assembly (includes Items 2-3)
Not sold separately
2
  • Isolator, backrest (3)
52300323
3
  • Flange nut, locking, 1/4"-20 (3)
7716