RIDER AND PASSENGER FOOTPEG KIT
J065052019-01-15
GENERAL
Kit Number
    Edge Cut: 50500851, 50500857, 50500967, 50501020
    Willie G: 50500856, 50500858, 50501281, 50501282
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
Kit Contents
See Figure 4 and Table 1.
RIDER
REMOVE
1.
NOTE
Save all hardware, including torsion spring (1), for installation of the new footpegs (3).
See Figure 2. Remove and save the retaining clip (2) and pin (4) for future use.
Figure 1. Torsion Spring
INSTALL
1.
NOTE
See Figure 1. When performing the next step, verify that the spring is positioned inside of the footpeg.
See Figure 2. Install pegs.
a.
Insert short leg of torsion spring (1) into hole in new footpeg (3).
b.
Align long leg of torsion spring (1) to hole in footpeg mount and insert.
c.
Rotate footpeg (3) into position in clevis and insert pin (4) through clevis, footpeg (3) and spring (1).
d.
Install retaining clip (2).
e.
Repeat on other side.
2.
Willie G Rider Pegs (Only)- adjust orientation as follows:
a.
For forward controls, foot surface to be parallel to the mounting pin.
b.
For mid controls, foot surface to be parallel to ground.
c.
Tighten adjustment screw.
Torque: 28.5 N·m (21 ft-lbs)
1Torsion spring
2Retaining clip
3Footpeg
4Pin
Figure 2. Rider Footpeg Torsion Spring Installation
PASSENGER
REMOVE
1.
NOTE
Save all hardware, including detent spring (3), detent ball (4) and cage (6) for installation of the new footpegs (2).
See Figure 3. Remove and save the retaining clip (5) and pin (1) for future use.
INSTALL
1.
NOTE
When performing the next step, verify that the spring (3) and ball (4) are positioned inside of the footpeg (2).
Install pegs.
a.
Insert detent spring (3) into new footpeg (2), followed by detent ball (4).
b.
Position cage (6) on footpeg clevis edge while capturing the detent ball (4) and detent spring (3) inside cage (6).
c.
Slide cage (6) onto footpeg clevis.
d.
Align cage (6) and footpeg (2) with footpeg mount on vehicle.
e.
Install pin (1).
f.
Install retaining clip (5).
WARNING
Footrests must fold up and toward rear of motorcycle if struck. Failure to set footrests to fold up and back could result in death or serious injury. (00366a)
2.
Willie G Passenger Pegs (only) - adjust orientation as follows:
a.
See Figure 4. Loosen adjustment screw (5). Rotate to desired orientation.
b.
Fold peg up to stowed position and confirm clearance to other components. Adjust as necessary.
c.
Tighten adjustment screw.
Torque: 28.5 N·m (21 ft-lbs)
1Pin
2Footpeg
3Detent spring
4Detent ball
5Retaining clip
6Cage
Figure 3. Passenger Footpeg Detent Ball Installation
SERVICE PARTS
Figure 4. Service Parts: Footpeg Kit
Table 1. Service Parts Table
Kit
Item
Description (Quantity)
Part Number
50500967
1
Rider, Edge Cut foot peg, RH
Not Sold Separately
2
Rider, Edge Cut foot peg, LH
Not Sold Separately
3
Rings (6)
11306
4
Wear Peg (2)
50500972
50500851, 50501020
1
Rider, Edge Cut foot peg (2)
Not Sold Separately
3
Rings (6)
11306
50500857
1
Passenger, Edge Cut, foot peg (2)
Not Sold Separately
3
Rings (6)
11306
50500856, 50501281
1
Rider, Willie G skull, foot peg, LH
Not Sold Separately
2
Rider, Willie G skull, foot peg, RH
Not Sold Separately
5
Button socket screw (2)
50500856: 94409-03
50501281: 10200854
50500858, 50501282
1
Passenger, Willie G skull, foot peg, LH
Not Sold Separately
2
Passenger, Willie G skull, foot peg, RH
Not Sold Separately
5
Button socket screw (2)
50500858: 94409-03
50501282: 10200854