TIMER COVER KITS
J062782019-01-15
GENERAL
Kit Numbers
25600064, 25600065, 25600066, 25600067, 25600068, 25600081, 25600085, 25600097, 25600098, 25600099, 25600105, 25600109, 25600115, 25600135, 25600142
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
Kit Contents
See Figure 1 and Table 1.
INSTALLATION
For All Kits
1.
See Figure 1. Remove and discard the original screws and timer cover. For Kit 25600064 and 25600142, retain the original screws.
2.
Place new timer cover (1) in position and secure with screws (2). For Kit 25600064 and 25600142, secure the timer cover using the original screws (A).
3.
Secure screws. Tighten.
Torque: 1.7–2.3 N·m (15–20 in-lbs) TORX head screw
SPECIAL CARE INSTRUCTIONS
NOTE
To prevent damage to the chrome surface, do not use any detergents, chemical solvents, polishes or abrasive cleaning agents.
To keep this surface in best condition, lightly wipe with a MICROFIBER DETAILING CLOTH (94663-02) using clear water or a mild Harley-Davidson cleaner such as:
NOTE
These cleaners are available from a Harley-Davidson dealer.
CARE AND CLEANING GUIDELINES FOR BRASS PARTS
Cleaning Instructions
  1. Verify part is dry and free of dirt or debris.
  2. Place a small amount of Harley-Davidson® Chrome Clean & Shine on a microfiber cloth or detailing swab.
  3. Using light pressure, rub the brass parts with the microfiber cloth. For hard to reach places or grooves, use the detailing swab.
Obtaining a Bright Finish
Brass parts will naturally age and darken with time. If a bright brass finish is preferred, place some Harley-Davidson Bare Metal Polish on a microfiber cloth and lightly rub on the brass parts until they reach the desired brightness.
Slowing the Natural Aging Process
To slow the aging process of the brass parts, place a small amount of Harley-Davidson Glaze Poly Sealant on a microfiber cloth or detailing swab, and lightly rub on the parts until the sealant has soaked in.
Precautions
  • Use of non-recommended cleaning, polishing and protective products will result in the removal of the aged finish from the brass parts.
  • Prolonged contact with certain items (hands, gloves, boots, dust, etc.) and exposure to the elements will also alter all surface finishes and is NOT considered a defect.
  • Avoid cleaning parts with abrasive and aggressive chemicals and abrasive cleaning pads.
  • Avoid ammoniated products and bleach.
  • Prolonged exposure to water will alter the brass finish. Wipe down parts after contact with water.
  • Excess rubbing may lighten the surface appearance of the part.
SERVICE PARTS
Figure 1. Timer Cover Kits
Table 1. Timer Cover Kits
Item
Description (Quantity)
Part Number
1
Timer cover
Not Sold Separately
2
Screw, TORX® chrome (Kit 25600097, 25600099, 25600065, 25600066, 25600067, 25600068, 25600115) (2)
9462
Screw, TORX® black (Kit 25600081) (2)
10200434
Screw, TORX® black (Kit 25600098, 25600105, 25600109) (2)
10200593
Screw, TORX® stainless steel (Kit 25600085) (2)
10200614
Screw, TORX® black (Kit 25600135) (2)
10200812
Items referenced but not included in kit:
A
Screw (Kit 25600064, 25600142-Use OE screw) (2)
68120-00