ANNIHILATOR FRONT WHEEL KITS
J066532019-01-15
GENERAL
WARNING
Install only wheels and installation kits approved for your model motorcycle. Contact a Harley-Davidson dealer to verify fitment. Mismatching wheels and installation kits or installing wheels not approved for your model can cause loss of control, which could result in death or serious injury. (00610c)
Kit Numbers
43300587, 43300588, 43300589, 43300590, 43300591, 43300592, 43300593
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Kit Contents
This kit includes a custom wheel only. See Figure 2 and Table 3 for kit contents.
Additional Parts Required
Proper installation of this kit requires the separate purchase of the following parts which are available at a Harley-Davidson dealer:
Recommended Products
The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning:
  • Chrome Clean & Shine (93600031 (US) / 93600082 (International))
  • Glaze Poly Sealant (93600026 (US) / 93600079 (International))
  • Harley®Preserve Bare Aluminum Protectant (99845-07)
  • Harley® Wheel and Spoke Brush (43078-99)
  • Wheel & Tire Cleaner (93600024 (US) / 93600076 (International))
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
Figure 1. Front Brake Disc
Table 1. Front Disc Hardware Fitment
Brake Disc
Hardware
Closed disc
5 Stock disc screws (3655A)
Chrome screw kit (46646-05) includes 5 screws
NOTE: Models equipped with dual front brakes and models being equipped with a wheel with dual brake mounting surfaces require twice as many screws and washers (10 total screws or 2 chrome screw kits if available).
INSTALLATION
1.
Remove existing front wheel assembly. Retain axle, axle nut, brake disc and wheel spacers for kit installation. See the service manual.
NOTE
  • Install valve stem (40999-87) included in the installation kit.
2.
See Figure 2. Install valve stem assembly on wheel. See the service manual.
NOTE
Install the primary bearing first using appropriate service manual and WHEEL BEARING INSTALLER/REMOVER 94143-09A.
  • The left side of the wheel has a groove machined into the hub to identify it as the primary bearing side.
  • The wheel should be installed so that the groove is on the left side of the motorcycle.
  • The brake disc is installed on the left side of the wheel.
NOTICE
Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c)
3.
Assemble the wheel installation, kit components and brake disc(s) to wheel, using the appropriate service parts table. See the service manual.
4.
When installing tire, ensure protective covers are installed on the tire mounting machine to avoid paint chipping.
5.
Install previously removed wheel spacers. See service manual.
6.
Install front wheel (1), stock axle and stock axle nut. See service manual.
MAINTENANCE AND CLEANING
Parts must be maintained regularly so that they keep their original shine and luster.
  1. Clean heavily-soiled wheel surfaces using Wheel & Tire Cleaner, applied with Harley Wheel and Spoke Brush.
  2. Thoroughly clean wheel with a good quality cleaner, such as Wheel & Tire Cleaner.
  3. After cleaning and polishing, seal the finish with a good quality sealer, such as Glaze Poly Sealant.
WARNING
Harley-Davidson recommends the use of its specified tires. Harley-Davidson vehicles are not designed for operation with non-specified tires, including snow, moped and other special-use tires. Use of non-specified tires can adversely affect stability, handling or braking and lead to loss of vehicle control, which could result in death or serious injury. (00024d)
Table 2. Specified Tire Combination
Kit Installation
Specified Tire
Front Tire Part No.
REAR TIRE PART NO.
2018 - later FLSB
Michelin Scorcher "31"
43100015
43200038A
2018 - later FXBB
Dunlop D401F
43100033
43200035
2018 - later FXFB
Dunlop D429
43100039
43200039
2018 - later FXLR
Michelin Scorcher "31"
43100038
43200038A
SERVICE PARTS
Figure 2. Service Parts: Front Wheel Kit
Table 3. Service Parts and Wheel Kit Contents
Kit
Item
Description (Quantity)
Part Number
43300587, 43300588, 43300589, 43300590, 43300591, 43300592
1
Wheel
Not Sold Separately
Visual indicator mentioned in text:
2
Groove
Table 4. Front 25 mm Bearing ABS Wheel Installation Kit (42400034)
Front 25 mm Bearing ABS Wheel Installation Kit (42400034)
Item Quantity Used and Description
Fitment
Wheel Size
A
B
C
D
E
F
G
H
2018 and later FLSB
18x3.5
1
1
0
1
0
0
1
1
2018 and later FXBB and FXLR
19x2.5
1
1
0
0
1
0
1
1
2018 and later FXFB
16x3.0
1
1
0
1
0
0
1
1
Installation kits are designed to work with many different wheel styles and fitments. Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on.
A
Bearing, Regular
9276B
B
Bearing, ABS
9252A
C
Axle Sleeve
43300480
D
Axle Sleeve
43300483
E
Axle Sleeve
43300454
F
Axle Sleeve
43300457
G
Valve Stem, Pull Thru
40999-87
H
Valve Stem, Cap
41123-79
Table 5. Front 25 mm Bearing Wheel Installation Kit (42400033)
Front 25 mm Bearing Wheel Installation Kit (42400033)
Item Quantity Used and Description
Fitment
Wheel Size
A
D
E
G
H
2018 and later FXBB, and FXLR
19x2.5 in
2
0
1
1
1
2018 and later FXFB
16x3.0 in
2
1
0
1
1
Installation kits are designed to work with many different wheel styles and fitments. Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on.
A
Bearing, Regular (2)
9276B
D
Axle Sleeve
43300483
E
Axle Sleeve
43300454
G
Valve Stem, Pull Thru
40999-87
H
Valve Stem, Cap
41123-79