DERBY COVER KIT
J060202019-01-15
GENERAL
Kit Numbers
25700434, 25700435, 25700436, 25700437, 25700446, 25700469, 25700471, 25700472, 25700473, 25700474, 25700476, 25700477, 25700505, 25700515, 25700571, 25700572, 25700573, 25700703, 25700704, 25700705, 25700740, 25700768, 25700822, 25700825, 25700826, 25700843, 25700844, 25700887, 25700888, 25700987, 25700988, 25701020, 25701022, 25338-99B
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Kit Contents
See Figure 3 and Table 1.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
PREPARE
1.
Remove the main fuse. See the owner's manual.
REMOVE
1.
Remove original equipment (OE) derby cover and retain mounting screws with captive washers.
2.
Inspect O-ring for damage. Replace if necessary.
INSTALL
1.
Kits 25700435, 25700436, 25700446, 25700469, 25700471, 25700472, 25700473, 25700474, 25700476, 25700505, 25700740, 25700843, 25700844, 25700887, 25700888, 25700987, 25700988, 25701020, 25701022, 25338-99B: Install new derby cover (1), O-ring and new screws (2) and washers (3).
2.
Kits 25700434, 25700437, 25700477: Install new derby cover (1), O-ring and original equipment (OE) screws (2) with captive washers.
3.
Kits 25700571, 25700572, 25700573, 25700703, 25700704, 25700705: Install new derby cover (1), O-ring and new screws (2) and washers (3). Note that one screw (4) is longer and must be located in the 2 o'clock position on the derby cover as shown in Figure 3.
4.
Kits 25700515, 25700768, 25700822, 25700825, 25700826: Install new derby cover (1) and new screws (2) as shown in Figure 3. No washers are used with this kit.
5.
See Figure 1. Tighten derby cover screws (2,4) in sequence shown.
Torque: 9.5–12.2 N·m (84–108 in-lbs) Derby cover mounting screws
6.
Kits 25700768, 25700822, 25700825, 25700826 only: See Figure 2. Install decorative screws in cover.
a.
Tighten screws
Torque: 1.69–2.25 N·m (15–20 in-lbs) Six small screws
Figure 1. Torque sequence
Figure 2. Decorative screws
COMPLETE
1.
Install main fuse. See owner's manual.
SPECIAL CARE INSTRUCTIONS
NOTE
To prevent damage to the cover surface, do not use any detergents, chemical solvents, polishes or abrasive cleaning agents.
To keep this surface in best condition, lightly wipe with a MICROFIBER DETAILING CLOTH (94663-02) using clear water or a mild Harley-Davidson cleaner such as:
NOTE
These cleaners are available from a Harley-Davidson dealer.
CARE AND CLEANING GUIDELINES FOR BRASS PARTS
Cleaning Instructions
  1. Verify part is dry and free of dirt or debris.
  2. Place a small amount of Harley-Davidson® Chrome Clean & Shine on a microfiber cloth or detailing swab.
  3. Using light pressure, rub the brass parts with the microfiber cloth. For hard to reach places or grooves, use the detailing swab.
Obtaining a Bright Finish
Brass parts will naturally age and darken with time. If a bright brass finish is preferred, place some Harley-Davidson Bare Metal Polish on a microfiber cloth and lightly rub on the brass parts until they reach the desired brightness.
Slowing the Natural Aging Process
To slow the aging process of the brass parts, place a small amount of Harley-Davidson Glaze Poly Sealant on a microfiber cloth or detailing swab, and lightly rub on the parts until the sealant has soaked in.
Precautions
  • Use of non-recommended cleaning, polishing and protective products will result in the removal of the aged finish from the brass parts.
  • Prolonged contact with certain items (hands, gloves, boots, dust, etc.) and exposure to the elements will also alter all surface finishes and is NOT considered a defect.
  • Avoid cleaning parts with abrasive and aggressive chemicals and abrasive cleaning pads.
  • Avoid ammoniated products and bleach.
  • Prolonged exposure to water will alter the brass finish. Wipe down parts after contact with water.
  • Excess rubbing may lighten the surface appearance of the part.
SERVICE PARTS
Figure 3. Service Parts: Derby Cover Kit
Table 1. Service Parts Table: Derby Cover Kits
Kit
Item
Description (Quantity)
Part Number
25700435, 25700436, 25700843, 25700844, 25338-99B
1
Derby Cover
Not sold separately
2
Screw (Chrome) (5)
9461
3
Washer (Chrome) (5)
9600
25700446, 25700469, 25700471, 25700472, 25700473, 25700474, 25700476, 25700505, 25700888, 25700987
1
Derby Cover
Not sold separately
2
Screw (Chrome) (5)
10200409
3
Washer (Chrome) (5)
9600
25700434, 25700437, 25700477
1
Derby Cover
No service parts
25700571, 25700572, 25700573, 25700703, 25700704, 25700705
1
Derby Cover
Not sold separately
2
Screw (Chrome) (4)
9461
3
Washer (Chrome) (5)
9600
4
Screw, long (Chrome)
10200587
25700515
1
Derby Cover
Not sold separately
2
Screw (Black) (5)
10200436
Medallion, bar & shield (not shown)
14101000
25700740, 25701020, 25701022
1
Derby Cover
Not sold separately
2
25700740: Screw (5)
10200550
25701020: Screw (5)
10200815
25701022: Screw (5)
10200816
3
Washer (5)
10300103
25700768, 25700822, 25700825, 25700826
1
Derby Cover
Not sold separately
2
Screw, hexhead socket, SEMS (5)
3061
Screw (Stainless) (6) (not shown)
10200659
25700887, 25700988
1
Derby Cover
Not sold separately
2
Screw (Black) (5)
10200655
3
Washer (Black) (5)
10300152