REAR TURBINE WHEEL
J054792018-08-21
GENERAL
WARNING
Install only wheels and installation kits approved for your model motorcycle. Contact a Harley-Davidson dealer to verify fitment. Mismatching wheels and installation kits or installing wheels not approved for your model can cause loss of control, which could result in death or serious injury. (00610c)
Kit Number
40900057, 40900324, 40900403, 40900405, 40900622
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Kit Contents
These kits include custom wheel only. See Figure 1 and Table 2.
Additional Parts Required
Proper installation of these kits require separate purchase of the following parts which are available at a Harley-Davidson dealer.
  • Wheel Installation Kit (Refer to Table 3 through Table 5 to determine required installation kit).
  • Brake Disc Screws (Refer to Table 1 to determine proper hardware).
  • For kits 40900057, 40900324 and 40900622: Rear Sprocket Screws (Refer to Table 1 to determine proper hardware).
  • Wheel Bearing Remover and Installer (94134-09)
  • For kits 40900403 and 40900405: Optional Harley-Davidson Original Equipment angled valve stem may be installed. See a Harley-Davidson dealer for part numbers and proper torque values.
The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning:
  • Chrome Clean & Shine (93600031 (US) / 93600082 (International))
  • Glaze Poly Sealant (93600026 (US) / 93600079 (International))
  • Harley® Wheel and Spoke Brush (43078-99)
  • Wheel & Tire Cleaner (93600024 (US) / 93600076 (International))
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
Table 1. Rear Disc and Sprocket Hardware Fitment
Hardware
Fitment
Rear Disc Screws (select stock or chrome hardware)
5 Stock disc screws (43567-92)
All models
Chrome screw kit (46647-05) includes 5 screws
All models
Rear Sprocket Screws (select stock or chrome hardware)
5 Sprocket screw, stock (3109)
2007 and later Dyna and Softail, 2007 Touring
Chrome screw kit (94773-07) includes 5 screws and washers
2007 and later Dyna and Softail
5 Sprocket screw, stock (3737A)
2000-2005 Dyna, 2000-2006 Softail, 2004-2006 Touring
Chrome screw kit (94773-00A) includes 5 screws and washers
2000-2005 Dyna, 2000-2006 Softail
5 Sprocket screw, stock (3814)
2008 Touring
5 Sprocket screw, stock (3873)
2006 Dyna
5 Sprocket screw, stock (3899)
2000-2003 Touring, 2001 and later Sportster (except Japanese models)
5 Sprocket screw, stock (40439-01)
2002-2006 VRSC and 2007 VRSCR models
5 Sprocket screw, stock (4552)
2007 and later VRSC models (except VRSCR and VRSCSE models)
Rear Sprocket Washers
5 Sprocket washer, stock (6516HW)
2006 and earlier Dyna, Softail and Touring and 2000 and later Sportster models (except Japanese models)
5 Sprocket washer, stock (7039)
2002 and later VRSC
INSTALLATION
1.
Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. See service manual.
NOTE
Prior to removing or installing the wheel, the rear brake caliper must be removed.
The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from your dealer. See your dealer for the correct part number for your model motorcycle.
NOTE
Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems.
NOTICE
Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c)
NOTICE
Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b)
2.
See Figure 1. Install valve stem assembly (H) on wheel. See service manual.
3.
Assemble wheel installation kit components, stock brake disc, and sprocket to wheel using the appropriate service parts table. See service manual.
NOTE
Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. Do not install Bearing Shim with this wheel.
For kits 40900057 and 40900324: The machined grooves on the right side of the wheel indicate the primary bearing side.
4.
Install rear wheel (1), stock axle and stock spacers to motorcycle. See service manual.
MAINTENANCE AND CLEANING
Chrome parts must be maintained regularly to keep their original shine and luster.
  1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush.
  2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner.
  3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant.
SERVICE PARTS
Figure 1. Service Parts: Rear Turbine Wheel
Table 2. Service Parts and Wheel Kit Contents
Kit
Item
Description (Quantity)
Part Number
40900057, 40900324, 40900403, 40900405,
40900622
1
Wheel
Not Sold Separately
Visual indicator mentioned in text:
4
Machined grooves
Table 3. REAR 25mm Bearing Wheel Installation Kit (41456-08C)
REAR 25 MM Bearing Wheel Installation Kit (41456-08C)
Item (Quantity Used and Description)
Fitment
Wheel Size
A
C
D
E
F
H
I
J
2009 and later FLT without ABS
16 x 5.0 in
2
1
0
0
0
*
*
*
2009 and later FLT without ABS
18 x 5.0 in
2
1
0
0
0
*
*
0
2008 VRSCD without ABS
18 x 5.5 in
2
0
0
1
**
*
*
0
2008 and later FXCW and FXCWC without ABS
18 x 8.0 in
2
0
1
0
0
*
*
0
2008 - 2017 VRSCAW, VRSCDX and VRSCF without ABS
18 x 8.0 in
2
0
0
1
**
*
*
0
Installation kits are designed to work with many different wheel styles and fitments. Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on.
NOTES:
* See NOTE above valve installation step in INSTALLATION to determine which valve stem to use for your particular kit. Discard other valve stem(s).
** See INSTALLATION to determine if shim is required.
*** Bearing shim installed under primary bearing.
A
Bearing, regular (2)
9276
C
Axle sleeve
41349-07
D
Axle sleeve
41358-08
E
Axle sleeve
43704-08
F
Bearing shim***
41447-08
H
Valve stem, short
43157-83A
I
Valve stem, long
43206-01
J
Valve stem, pull thru
40999-87
Table 4. REAR 25 MM Bearing ABS Wheel Installation Kit (41453-08C)
REAR 25 MM Bearing ABS Wheel Installation Kit (41453-08C)
Item (Quantity Used and Description)
Fitment
Wheel Size
A
B
C
D
E
F
G
H
I
J
2008 FLT with ABS
16 x 3.0 in
1
1
0
1
0
0
1
*
*
0
2009 and later FLT with ABS
16 x 5.0 in
1
1
1
0
0
0
0
*
*
*
2009 and later FLT with ABS
18 x 5.0 in
1
1
1
0
0
0
0
*
*
0
2008 VRSCDa with ABS
18 x 5.5 in
1
1
0
0
1
**
0
*
*
0
2008 - 2017 VRSCAWa, VRSCDXa, VRSCXa and VRSCFa with ABS
18 x 8.0 in
1
1
0
0
1
**
0
*
*
0
Installation kits are designed to work with many different wheel styles and fitments. Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on.
NOTES:
* See NOTE above valve installation step in INSTALLATION to determine which valve stem to use for your particular kit. Discard other valve stem(s).
** Primary bearing. Bearing must be installed with red side facing the wheel.
*** Bearing shim installed under primary bearing.
A
Bearing, regular
9276
B
Bearing, ABS**
9252
C
Axle sleeve
41349-07
D
Axle sleeve
41900-08
E
Axle sleeve
43704-08
F
Bearing shim***
41447-08
G
Bearing shim***
43904-08
H
Valve stem, short
43157-83A
I
Valve stem, long
43206-01
J
Valve stem, pull thru
40999-87
Table 5. REAR 25 MM Bearing ABS Wheel Installation Kit (43077-11A)
REAR 25 MM Bearing ABS Wheel Installation Kit (43077-11A)
Item (Quantity Used and Description)
Fitment
Wheel Size
A
B
C
D
E
H
I
2011 and later FLSTN, FLSTC, FLS and FXS with ABS
16 x 3.0 in
1
1
0
1
0
*
*
2011 and later FXST, FLSTF and FLSTFB with ABS
17 x 6.0 in
1
1
0
1
0
*
*
2011 and later FXST, FLSTF and FLSTFB with ABS
18 x 6.0 in
1
1
0
1
0
*
*
2011 and later FXCWC with ABS
18 x 8.0 in
1
1
1
0
0
*
*
2017 and later XG500 and XG750 with ABS
15 x 3.5 in
1
1
0
0
1
*
*
Installation kits are designed to work with many different wheel styles and fitments. Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on.
NOTES:
* See NOTE above valve installation step in INSTALLATION to determine which valve stem to use for your particular kit. Discard other valve stem(s).
** Primary bearing. Bearing must be installed with red side facing the wheel.
A
Bearing, regular
9276
B
Bearing, ABS**
9252
C
Axle sleeve
41358-08
D
Axle sleeve
41696-08
E
Axle sleeve
43300098
H
Valve stem, short
43157-83A
I
Valve stem, long
43206-01