HEATED HAND GRIP KITS
J042592019-02-15
GENERAL
Kit Numbers
56047-08A, 56049-08A, 56196-08A, 56512-08A, 56828-08A, 56926-08A, 56100027, 56100047, 56100107, 56100253, 56100255, 56100257, 56100258, 56100260, 56100263, 56100267, 56100362
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
These grips have EXTERNAL left side power wires. These wires can not be wired internally.
Installation Requirements
Unless already installed:
2017-Later Touring Models require separate purchase of an Electrical Connection Harness (Part No. 69201599A).
2014-2016 Touring Models require separate purchase of an Electrical Connection Harness (Part No. 69200722).
2016-2017 Softail Models require separate purchase of an Electrical Connection Harness (H-D Part No. 72673-11)
2018-Later Softail Models require separate purchase of an Electrical Connection Harness (Part No. 69201599A).
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
ELECTRICAL OVERLOAD
NOTICE
It is possible to overload your vehicle's charging system by adding too many electrical accessories. If the combined electrical accessories operating at any one time consume more electrical current than the vehicle's charging system can produce, the electrical consumption can discharge the battery and cause damage to the vehicle's electrical system. See an authorized Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories or for necessary wiring changes. (00211c)
WARNING
When installing any electrical accessory, be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modified. Exceeding the maximum amperage can lead to electrical failures, which could result in death or serious injury. (00310a)
This kit requires up to 2.8 amps more current from the electrical system.
Kit Contents
Each kit contains one pair of heated hand grips plus connecting parts. See Figure 8 and Table 1.
PREPARATION
WARNING
To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
NOTE
  • For vehicles equipped with security siren: With security fob present, turn ignition switch ON. Disarm security system. IMMEDIATELY remove the main fuse per the service manual.
  • For vehicles WITHOUT security siren: See the service manual to remove the main fuse.
WARNING
When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a)
  1. Remove the fuel tank per the service manual.
1Screw (2)
2Handlebar clamp
3Clutch hand lever assembly
4Upper switch housing
5Lower switch housing
6Left handlebar grip
7Larger diameter of flange
8Grooves
Figure 1. Left Handlebar Switch Housing (2008-2013 Touring and 2006-Later Softail)
REMOVAL
Left-Side Grip Removal
NOTE
  • Cover painted parts to protect finish.
1.
Refer to the service manual for specific information on the following generalized steps.
a.
Refer to Figure 1 or Figure 2. Loosen two screws (1) and the handlebar clamp (2).
b.
Position the clutch hand lever assembly (3) away from the switch housing.
c.
Separate the two switch housing sections (4, 5).
2.
With "glueless" grip: Remove the grip from the handlebar. With glued grip: Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife.
1Screw (2)
2Handlebar clamp
3Clutch hand lever assembly
4Front switch housing
5Back switch housing
6Shield
7Trigger finger switch cap
Figure 2. Left Handlebar Switch Housing (2014-Later Touring)
Right-Side Grip Removal
2008-2013 Touring Models:
NOTICE
Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a)
NOTE
Use the eyelet of a cable strap if the cardboard insert is not available. See Figure 3.
ALL Models:
  1. Refer to the service manual for specific information on the following generalized steps.
    1. Loosen two screws and the handlebar clamp.
    2. Position the brake lever/master cylinder assembly away from the switch housing.
    3. Separate the two switch housing sections.
    4. 2008-2013 Touring Models: Remove the friction shoe if present.
  2. ALL Models: Remove the grip from the handlebar.
NOTE
  • The twist grip sensor in the right side of the handlebar has a seal cap that protects internal electrodes from dirt and moisture. The seal cap also serves as a retention device for the throttle grip.
  • Tug hand grip to remove.
  • Upon removing the grip, check the location of the seal cap.
If the seal cap is still fastened to the index pins inside the old throttle grip, it can be discarded along with the grip.
If the seal cap is still fastened to the end of the twist grip sensor:
  • See Figure 4. Insert a small screwdriver or other flat-blade tool into the flat area on one side of the seal cap.
  • Press the leg on the underside of the cap to free it from the slot at the end of the twist grip sensor. Pry up one end of the cap.
  • Repeat on the other side of the cap.
  • Carefully remove the cap and discard it.
15/32-inch (4 mm) thick insert
2Brake lever
3Brake lever bracket
Figure 3. Protect Stop Light Switch
1Handlebar
2Throttle twist grip sensor
3Seal cap
Figure 4. Remove Seal Cap
INSTALLATION
NOTE
The throttle grip sensor has two wires, covered in sheathing, coming out of the end that goes into the handlebar. These wires either:
  • Have black heat shrink tubing over them, or
  • are terminated with a two-cavity electrical connector
NOTE
Some internally wired handlebars, like Chizeled or models with handlebar-mounted turn signals, de-pinning the heated grip connectors may be required.
  • Take a photo of all connectors for reassembly prior to de-pinning
  • To aid in pulling wires, spray/rub with soapy water
1.
See TWIST GRIP SENSOR: REMOVAL in the service manual. Follow the instructions for the specific model vehicle to:
a.
Access the six-way twist grip sensor jumper harness connector [204] inside the vehicle. Unplug the connector halves.
b.
Gently pull twist grip sensor out of handlebar only as far as necessary to access black heat shrink tubing or heated grip connector.
2.
See Figure 8. Get the left side heated grip (1), long wire harness (15) and short wire harness extension (8) from the kit. Determine if the extension is required for this installation: Does the connector extend past the opposite end of the handlebar? If YES: The extension is not needed. It can be discarded. Disconnect the wire harness from the left side grip. If NO: Disconnect the wire harness from the left side grip. Connect the extension to the connector on the wire harness. Set the left side grip, and the wire harness or harness assembly aside.
a.
Temporarily connect the wire harness to the connector on the end of the left heated hand grip.
b.
Hold the grip and attached wire harness in position along outside of handlebar as if the assembly were installed on the handlebar.
c.
The connector at the end of the wire harness must extend past the right end of the handlebar.
NOTE
DO NOT cut any wires leading to the green connector on the twist grip sensor. Cut off the black heat shrink tubing ONLY.
d.
Locate the pass-thru connector on the twist grip sensor. This is a 2-way pin side connector see service manual for location.
3.
Locate the black harness coming from the center of the twist grip sensor.
4.
Get the wire harness set aside in Step 2.
5.
Connect the socket housing on the sensor wires to the black pin housing at the end of the wire harness.
NOTE
Air pressure or an electrical fish tape can be used to thread the wire harness completely through the handlebar.
6.
Thread the connector and twist grip sensor wire harnesses into the right side of the handlebar.
a.
While feeding the wiring into the handlebar, gently pull the connector at the end of the twist grip sensor jumper harness to draw the twist grip sensor into the handlebar.
b.
Thread the left side heated grip wire harness all the way through and out the left side of the handlebar.
c.
Fit the index tabs on the twist grip sensor into the slots in the handlebar. One index tab and one slot are smaller than the others to prevent improper assembly.
NOTE
  • Thoroughly clean handlebar to remove all residual adhesive.
  • Remove the protective ring (marked "REMOVE PRIOR TO ASSEMBLY") from the end of the new left side grip.
7.
Fasten the white socket housing to the new left side heated hand grip (1).
2008-2013 Touring and 2016 and Later Softail Models:
1.
See Figure 1. Position the left side heated grip (6) so the larger diameter portion of the flange (7) is at the bottom. Push the grip fully onto the handlebar.
a.
Position the lower switch housing beneath the grip. The grooves (8) on the outboard side of the switch housing must fit over the flange on the end of the grip.
b.
Position the upper switch housing over the handlebar and lower switch housing.
c.
Start the upper and lower switch housing screws, but do not tighten. Verify that the wire harness conduit runs in the depression at the bottom of the handlebar.
d.
Position the clutch hand-lever assembly inboard of the switch housing assembly. Engage the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket.
e.
Align the hole in the handlebar clamp with the hole in the clutch lever bracket. Start the lower screw with flat washer. Adjust the switch housing and clutch hand control position for rider comfort.
f.
Tighten first the upper, then the lower handlebar clamp screws.
Torque: 6.8–9 N·m (60–80 in-lbs)
g.
Tighten first the lower, then the upper switch housing screws.
Torque: 4–5.4 N·m (35–48 in-lbs)
2008-2013 Touring Models:
1.
See Figure 5. Locate the B+ (battery positive) connector (1) on the main electrical harness under the seat (a red wire with an unused gray connector). Remove the cover (2) from the connector.
2.
See Figure 8. Plug the adapter harness (11) from the kit into the B+ connector.
3.
Cut the heated hand grip harness red wire to within easy reach of the end of the adapter harness red wire. Use a sealed splice connector (4) from the kit to splice the two wires per the service manual.
1B+ connector
2Cover
Figure 5. B+ Connector
4.
Get the orange/white fuse block adapter wire (10) from the kit. Note the terminal on each end (see Figure 6. Only the terminal WITHOUT the spring tabs fits into the fuse cavity. Carefully cut the terminal WITH spring tabs from the wire and discard it.
1LEAVE this terminal on wire
2CUT this terminal from wire
3Spring tab (2)
Figure 6. Fuse Block Adapter Wire
5.
Locate the fuse cavity indicated as "P&A IGN" "2A MAX". There is a bus bar feeding one side of this circuit, but no mating wire or fuse is present. Remove the three existing fuses in this row, noting their location.
6.
Gently remove the orange plastic secondary lock from the fuse block. Insert the terminal on the orange/white adapter wire until it stops. Refer to a nearby factory-installed terminal for comparison to verify proper orientation and depth. Install the secondary lock.
7.
Cut excess length from the orange/white wire on the heated hand grip to within easy reach of the orange/white adapter wire installed in Step 8.
WARNING
Be sure to follow manufacturer's instructions when using the UltraTorch UT-100 or any other radiant heating device. Failure to follow manufacturer's instructions can cause a fire, which could result in death or serious injury. (00335a)
8.
Get the blue sealed splice connector (4) from the kit. Splice the orange/white wire from the heated hand grip power harness to the orange/white adapter wire per the service manual.
NOTE
  • Avoid directing heat toward any fuel system component. Extreme heat can cause fuel ignition/explosion resulting in death or serious injury.
  • Avoid directing heat toward any electrical system component other than the connectors on which heat shrink work is being performed.
  • Always keep hands away from tool tip area and heat shrink attachment.
9.
See Figure 8. Install a 2A fuse (13) from the kit into the P&A IGN fuse cavity to complete the circuit. Install the three fuses removed in Step 2 into the proper cavities.
10.
Install the dust cover onto the fuse block. Install the fuse block. Install the main fuse holder per the service manual.
11.
Open the cover of the fuse holder on the heated hand grip power harness. Plug the remaining 5A fuse (14) from the kit into the fuse holder. Close the cover.
12.
Check along the entire length of the wiring for rubbing, chafing or pinch points.
13.
Fasten the black wire with ring terminal to any ground stud on the frame. Proceed to COMPLETION.
2014-Later Touring Models:
Left Controls
1.
See Figure 2. 2014-2015 Models: Verify that the shield (6) is in correct position on the outboard side of the switch module.
a.
Install the switch housing sections (4, 5) onto the switch module. Tighten captive screws (1) until snug.
b.
Install clutch control lever assembly (3).
c.
Install handlebar clamp (2) with two screws removed earlier, but do not tighten.
d.
Secure switch housing screws. Tighten.
Torque: 4–5 N·m (35–44 in-lbs)
e.
Slide trigger finger switch cap (7) right to install.
f.
Tighten clutch handlebar clamp.
Torque: 6.8–9 N·m (60–80 in-lbs)
NOTICE
Do not route the handgrip main harness inside the switch housing. Wires routed inside the switch housing could result in short circuits and equipment damage. (00369a)
2.
Route the heated hand grip main wire harness between the hand grip and left switch housing, then under the switch housing.
3.
See Figure 8. Are there holes on the left underside of the handlebar?
a.
If YES: Install wire retainer clips (12) from the kit in the holes. Fasten the wire harness to the clips.
b.
If NO: Use cable straps (9) to fasten the wire harness to the handlebar.
Right Controls
1.
Obtain the new right side heated throttle grip (2) from the kit. Insert a screwdriver or other flat-blade tool between the body of the throttle grip and the end cap. Carefully pry the end cap off the grip.
NOTE
In the next step, DO NOT pull the plug from the throttle grip by grasping the wires or terminal pins. Only grasp the rubber tab on the plug.
2.
Tucked inside the outboard end of the throttle grip is a round rubber plug, with orange and green wires on one side and two pin terminals on the other. Using a needle-nose pliers or similar tool, carefully grasp the rubber tab on the wire side of the plug. Pull the plug out from the grip through the outboard opening.
3.
Thoroughly clean handlebar and inside of throttle grip to remove all dirt.
4.
NOTE
  • If handlebar grips are patterned, align pattern on right grip with pattern on left grip with throttle in fully closed position.
  • Follow all steps to ensure throttle grip free movement. Actuate the throttle grip to verify that it freely returns to the idle position.
See Figure 2. Slide the new heated throttle grip over the end of the handlebar. Rotate the grip to verify that the internal splines are engaged with the external splines on the twist grip sensor.
5.
Install switch housings. Tighten screws until snug.
6.
Install brake control assembly, but do not tighten.
7.
Tighten switch housings.
a.
Push hand grip inboard to verify that hand grip is fully seated.
b.
Move the switch housing assembly inboard (away from grip) to remove all end play. Then move the switch housing outboard 1–2 mm (0.040–0.08 in) to introduce end play.
c.
While holding switch housing in place, tighten switch housing screws.
Torque: 4–5.1 N·m (35–45 in-lbs)
d.
Verify that hand grip has slight inboard-outboard free play.
e.
Verify that hand grip rotates and returns freely.
8.
Secure brake control clamp screws. Tighten.
Torque: 6.8–9.0 N·m (60–80 in-lbs)
9.
Again verify hand grip rotation and slight end play.
10.
See Figure 1 and Figure 2 , which show the similar left side housing installation. Install the right side handlebar controls in the same way.
WARNING
Before starting engine, be sure throttle control will snap back to idle position when released. A throttle control that prevents engine from automatically returning to idle can lead to loss of control, which could result in death or serious injury. (00390a)
11.
Verify that the right grip/throttle sleeve rotates and returns freely. The sleeve must not bind on the handlebar or switch housing.
NOTE
The terminal sockets on the twist grip sensor are offset to one side. The pins can only be inserted one way.
12.
Using a needle-nose pliers or similar tool, carefully grasp the tab on the wire side of the round rubber plug at the outboard end of the throttle grip.
a.
Insert the plug back through the opening in the grip. Insert the terminal pins into the sockets at the end of the twist grip sensor.
b.
Press the rubber plug firmly to verify that the pins are fully seated in the sockets.
13.
Install the chrome end cap onto the end of the throttle grip.
Connection to Vehicle Wiring
  1. Follow existing wiring to route the heated hand grip main wire harness from the left side grip:
    1. through, across or around the fork bracket,
    2. along the vehicle frame,
    3. to a general location under the seat
  2. See Figure 8. Use cable straps (9) from the kit to fasten the hand grip wiring to wire harnesses along the vehicle frame. 2014-Later Models: Continue after Step 15.
2014-Later Touring Models
NOTE
Unless already installed, an Electrical Connection Harness (Part No. 69200722A for 2014-2016 Models or 69201599A for 2017 and Later Models, available separately) must be installed per the instructions in that kit.
1.
Follow instructions in the Electrical Connection Harness Kit to:
a.
Splice the orange/white wire in the hand grip kit to the violet/blue wire on the Electrical Connection Harness.
b.
Splice the red wire in the hand grip kit to the red/blue wire on the Electrical Connection Harness.
c.
Splice the black wire in the hand grip kit to the black wire on the Electrical Connection Harness.
d.
Install cap into 4-way pin side of connector if not used.
e.
Heat-shrink the sealed splices.
f.
Fasten the black wire with ring terminal to any ground stud on the frame. Proceed to COMPLETION.
2016-Later Softail Models
NOTE
2016-2017 models require separate purchase of an Electrical Connection Harness (H-D Part No. 72673-11 ).
Some 18-Later models may have a damper weight that needs to be removed inside the LH side of the handlebar.
18-Later models require separate purchase of an Electrical Connection Harness (H-D Part No. 69201599A).
1.
Locate the Digital Technician connector [91A] (a gray six-way Deutsch pin connector with a rubber boot) under the seat. Place the Electrical Connection Harness at connector [91A], but DO NOT connect now.
2.
Route the heated hand grip wires over to the Electrical Connection Harness. DO NOT cut off the in-line fuse holder on the red wire, but cut the wires to a suitable length to easily reach the sealed splice connectors on the Electrical Connection Harness.
3.
Splice the black hand grip wire to the black wires in the Electrical Connection Harness.
4.
Splice the orange/white hand grip wire to the red/yellow wires in the Electrical Connection Harness.
5.
Splice the red hand grip wire to the red/blue wires in the Electrical Connection Harness.
6.
Use a heat gun or suitable radiant-heating device to shrink the connector to the wires.
7.
Pull the rubber boot out from the gray Digital Technician pin connector [91A]. Cut the boot off the wires.
8.
Connect the socket housing of the Electrical Connection Harness to connector [91A].
9.
Insert the rubber boot into the open pin connector of the Electrical Connection Harness.
10.
Loosen or remove the four screws holding the ECM to the mounting bracket. Route the Electrical Connection Harness under the ECM connector. Secure the four screws. Tighten.
Torque: 5.1–6.2 N·m (45–55 in-lbs)
11.
Heat-shrink the sealed splices.
12.
Fasten the black wire with ring terminal to any ground stud on the frame. Proceed to COMPLETION.
COMPLETION
NOTE
DO NOT perform the following steps until the heated hand grips and all related wiring have been installed per this instruction sheet.
1.
Verify that the right grip/throttle sleeve rotates and returns freely. The sleeve must not bind on the handlebar or switch housing. DO NOT operate the vehicle unless the throttle functions properly.
2.
Verify handlebar rotates freely and fully from right to left without pulling on the wires.
NOTE
To prevent possible damage to the sound system, verify that the ignition switch is OFF before installing the main fuse.
1.
Verify that the ignition switch is OFF. See the service manual to install the main fuse.
2.
Install the fuel tank per the service manual. Install any other vehicle components removed earlier per service manual or kit instructions.
WARNING
After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b)
3.
See the service manual to install the seat.
NOTE
  • To prevent battery drain, these heated hand grips are designed to function only with the engine running. The hand grips produce peak heat with the engine running at cruising speed.
  • The heat settings on the heated hand grip control dial range from 1 (minimum) to 6 (maximum).
4.
Before starting the vehicle, check that the hand grips are not producing heat.
5.
Start the engine. Check the hand grips at all settings for proper heating.
Troubleshooting
See Figure 7 for the heated hand grip schematic diagram.
Hand Grips Do Not Produce Heat
1.
See Figure 1. Check for proper wire routing. The hand grip main harness must be routed outside of the switch housing. If the wires were routed internally, disassemble the left handlebar switch housing and inspect for pinched wires. If wires are pinched, replace the left side hand grip and repeat the installation process with the correct wire routing.
2.
Check the wire connections of the orange/white, red and black hand grip main wire harness wires.
a.
If a connection is damaged, loose or weak, repair the connection. Test the hand grips.
b.
If all connections are good, continue with the next step.
3.
Remove the left grip from the handlebar.
4.
Disconnect the connector on the left grip from the right grip wire harness.
5.
Check continuity across the two connectors in the left grip. If the test shows continuity, the hand grips are functional.
6.
Remove the seat according to service manual instructions.
7.
Start the vehicle.
8.
Check for 12 VDC across the red and black wires of the hand grip main wire harness.
a.
If 12 VDC is not present across the wires, check the fuse (14) in the wire harness and replace it if blown.
b.
If 12 VDC is not present, replace the left grip and wire harness and test the hand grips.
Hand Grips Produce Heat with Ignition (Key) Switch Off
If the hand grips produce heat with the ignition switch off, then either the hand grips are incorrectly wired to the vehicle, or the left side grip and wire harness are faulty.
Carefully check all heated hand grip wire connections on the vehicle. If the connections are correct, replace the heated hand grip main wire harness, then test the hand grips.
1Left hand grip
2Heat control
3Positive to main circuit breaker or battery + connector
4Fuse
5Positive to accessory power
6Negative ground
7Right hand grip
Figure 7. Heated Hand Grip Schematic
SERVICE PARTS
Figure 8. Service Parts, Heated Hand Grip Kits
SERVICE PARTS
Table 1. Service Parts
Kit
Item
Description (Quantity)
Part Number
Kit 56047-08A
Flame Heated Grips
1
Left-side heated grip
56100-04B
2
Right-side heated throttle grip (includes Item 3)
56048-08
3
  • End cap, right-side grip
55940-08
Kit 56049-08A
Ironside Heated Grips
1
Left-side heated grip
Not Sold
2
Right-side heated throttle grip (includes Item 3)
Not Sold
3
  • End cap, right-side grip
Not Sold
Kit 56196-08A
Chrome and Rubber
(Small Diameter)
Heated Grips
1
Left-side heated grip
56617-04B
2
Right-side heated throttle grip (includes Item 3)
56615-08
3
  • End cap, right-side grip
55950-08
Kit 56512-08A
Contoured Chrome and
Rubber Heated Grips
1
Left-side heated grip
56514-04B
2
Right-side heated throttle grip (includes Item 3)
56513-08
3
  • End cap, right-side grip
55949-08
Kit 56828-08A
Aileron Heated Grips
1
Left-side heated grip
Not Sold
2
Right-side heated throttle grip (includes Item 3)
Not Sold
3
  • End cap, right-side grip
Not Sold
Kit 56926-08A
Skull Collection
Heated Grips
1
Left-side heated grip
56927-05A
2
Right-side heated throttle grip (includes Item 3)
56928-08
3
  • End cap, right-side grip
55957-08
Kit 56100027
Slipstream Collection
Heated Grips
1
Left-side heated grip
56100038
2
Right-side heated throttle grip
56100032
3
  • End cap, right-side grip
56100024
Kit 56100047
Streamliner Collection
Heated Grips
1
Left-side heated grip
56100049
2
Right-side heated throttle grip
56100050
Kit 56100107
Airflow Collection
Heated Grips
1
Left-side heated grip
56100109
2
Right-side heated throttle grip
56100096
Kit 56100253
Airflow Collection
Heated Grips
1
Left-side heated grip
56100286
2
Right-side heated throttle grip
56100096
Kit 56100255
Streamliner Collection
Heated Grips
1
Left-side heated grip
56100285
2
Right-side heated throttle grip
56100050
Kit 56100257
Contoured Chrome and Rubber Collection
Heated Grips
1
Left-side heated grip
56100288
2
Right-side heated throttle grip
56513-08
Kit 26100258
Slipstream Collection
Heated Grips
1
Left-side heated grip
56100292
2
Right-side heated throttle grip
56100032
Kit 56100260
Skull Collection
Heated Grips
1
Left-side heated grip
56100293
2
Right-side heated throttle grip
56928-08
Kit 56100263
Flame Collection
Heated Grips
1
Left-side heated grip
56100296
2
Right-side heated throttle grip
56048-08
Kit 56100267
Chrome and Rubber Collection (Small Diameter)
Heated Grips
1
Left-side heated grip
56100295
2
Right-side heated throttle grip
56615-08
Kit 56100362
Willie G Skull Matte Black
Heated Grips
1
Left-side heated grip
56100369
2
Right-side heated throttle grip
56100370
Items common
to ALL Kits
4
Sealed splice connector (2)
70586-93
5
Ring terminal, #10 (2)
9857
6
Ring terminal, 1/4 inch (2)
9858
7
Ring terminal, 5/16 inch
9859
8
Wire harness, extension
69201703
9
Cable strap, black, 7.75 inches (197 mm) long
10006
10
Wire, fuse block adapter
70329-04
11
Wire harness, adapter
70310-04
12
Clip, wire retainer (4)
70345-84
13
Fuse, "mini" blade type, 2 Amp (gray) (for vehicle fuse block)
54305-98
14
Fuse, "mini" blade type, 5 Amp (light tan) (for inline fuse holder)
(NOTE: A 4 Amp fuse is permissible in this position)
72331-95
15
Wire harness, throttle sensor
69201713