RIDER & PASSENGER FOOTPEG KIT
J067232019-08-21
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
Time
50501382, 50501383, 50501388, 50501389,50501390, 50501395
Safety Glasses, Torque Wrench
1 h
(1) Tightening to torque value or other moderate tools and techniques required.
KIT CONTENTS
Figure 1. Kit Contents: Rider and Passenger Footpeg Kit
Table 2. Kit Contents: Rider and Passenger Footpeg Kit
Item
Qty
Description
Part No.
Notes
1
2
Screw, adjustment
2708A
28.5 N·m (21.0 ft-lbs)
2
2
Footpeg assembly, rider
50501492
Kit 50501382
50501490
Kit 50501389
50501491
Kit 50501383
50501489
Kit 50501390
3
2
Footpeg assembly, passenger
50501499
Kit 50501388
50501500
Kit 50501395
4
2
Trim, rider footpeg
Not sold separately
5
2
Wear peg
50501536
Kits 50501382, 50501389
4.52–5.08 N·m (40–45 in-lbs)
6
4
Screw
10200913
1.13–1.36 N·m (10–12 in-lbs)
NOTE
Verify all contents are present in the kit before installing or removing items from vehicle.
GENERAL
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Verify that you are using the most current version of the instruction sheet which is available at: www.harley-davidson.com/isheets.
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
Proper installation of this kit requires Loctite® 243 Threadlocker and Sealant - Blue (Part No. 99642-97).
INSTALL
Rider
1. See Figure 2. Remove pin (4) and retaining clip (2) and retain for installation. Save all hardware, including torsion spring (1), for installation of the new footpegs (3).
2. Insert short leg of torsion spring (1) into hole in new footpeg (3).
NOTE
When performing the next step, verify that the spring is positioned inside of the footpeg.
3. Align long leg of torsion spring (1) to hole in footpeg mount and insert.
4. Rotate footpeg into position in clevis and insert pin (4) through clevis, footpeg (3) and spring (1).
5. Install retaining clip (2).
6. Repeat on opposite side.
7. Adjust orientation:
a. Forward controls, foot surface to be parallel to the mounting pin.
b. Mid controls, foot surface to be parallel to ground.
8. See Figure 1. Tighten adjustment screw (1).
Torque: 28.5 N·m (21.0 ft-lbs)
9. Install trim (4) on footpeg. Apply 2 or 3 drops of Loctite 243 to screws (6). Install screws. Tighten.
Torque: 1.13–1.36 N·m (10–12 in-lbs)
1Torsion spring
2Retaining clip
3Footpeg
4Pin
Figure 2. Rider Footpeg Torsion Spring Installation
Passenger
1. See Figure 3. Remove pin (1) and retaining clip (5) and save. Save all hardware, including detent spring (3), detent ball (4) and cage (6) for installation of new footpegs.
2.
NOTE
When performing the next step, verify that the spring (3) is positioned inside of the footpeg (2).
Insert detent spring (3) into new footpeg (2).
3. Insert detent ball (4).
4. Position cage (6) onto footpeg clevis edge, capturing detent ball (4) and detent spring (3) inside cage (6).
5. Slide cage (6) onto footpeg clevis.
6. Align cage (6) and footpeg (2) with footpeg mount on vehicle.
7. Install pin (1) and retaining clip (5).
8. Adjust orientation:
a. Rotate to desired orientation.
b. Fold peg up to stowed position and confirm clearance to other components. Adjust as necessary.
c. See Figure 1. Tighten adjustment screw (1).
Torque: 28.5 N·m (21.0 ft-lbs)
9. See Figure 1. Install trim (4) onto footpeg. Apply 2 or 3 drops of Loctite 243 to screws (6). Install screws. Tighten.
Torque: 1.13–1.36 N·m (10–12 in-lbs)
1Pin
2Footpeg
3Detent spring
4Detent ball
5Retaining clip
6Cage
Figure 3. Rider Footpeg Torsion Spring Installation
WARNING
Footrests must fold up and toward rear of motorcycle if struck. Failure to set footrests to fold up and back could result in death or serious injury. (00366a)
WEAR PEG REPLACEMENT
1. See Figure 1. Remove existing wear peg (5) from footpeg.
2. Apply 2 or 3 drops of Loctite 243 to the wear peg (5). Install to footpeg. Tighten.
Torque: 4.52–5.08 N·m (40–45 in-lbs)