SOFTAIL QUARTER FAIRING BRACKET KIT
J067092019-08-21
Table 1.
Kits
Suggested Tools
Skill Level
Time
57001249, 57001250
Safety Glasses, Torque Wrench
1
1 h
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Service Parts: Fairing Bracket Kit
Table 2. Service Parts List: Fairing Bracket Kit
Item
Qty
Description
Part No.
Notes
1
1
Clutch cable retainer
37200428
Kit 57001249
2
1
Mounting bracket, LH
Not sold separately
3
2
Clamp, LH and RH
Not sold separately
4
4
Screw, 1/4-20 x 1/2
10200938
12.2–13.5 N·m (9–10 ft-lbs)
5
2
Tree fastener
12600194
6
4
Grommet
83483-09
7
1
Hood bracket
Not sold separately
8
1
Mounting bracket, RH
Not sold separately
9
2
Washer, plastic, adhesive backed
10300224
NOTE
Verify all contents are present in the kit before installing or removing items from vehicle.
GENERAL
Models
For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Make sure you are using the most current version of the instruction sheet which is available at: https://h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
These items are available at your local Harley-Davdson dealership.
FXBB with OE handlebars or FXLR with Tall Risers and Moto Bar kits:
  • Separate purchase of Right Hand Turn Signal Mount Bracket (Part No. 67800630) is required for this installation.
  • Separate purchase of Left Hand Turn Signal Mount Bracket (Part No. 12700164) is required for this installation.
  • Separate purchase of two Screw Locks (Part No. 67015-02) is required for this installation. FXBB only.
  • Separate purchase of Lock Washer (Part No. 7155) is required for this installation. FXBB only.
  • Separate purchase of Acorn Nut (Part No. 7331) is required for this installation. FXBB only.
REMOVE
FXLRS Speed Screen
1. See Figure 2. Remove speed screen
a. Remove screws and washers (8).
b. Pull speed screen (3) away from upper bracket (7).
c. Pull speed screen away from lower bracket (5) to remove posts from grommets.
2. Remove inner fairing.
a. Remove screws (1).
b. Remove inner fairing (2).
3. Remove upper bracket.
a. Remove screws (6).
b. Remove upper bracket (7).
4. Remove lower bracket.
a. Remove screws (4).
b. Remove lower bracket (5).
1Screw (2)
2Inner fairing
3Speed screen
4Screw (2)
5Lower bracket
6Screw with washer (2)
7Upper bracket
8Screw and washer (2)
Figure 2. FXLRS Speed Screen
FXLR Visor
1. See Figure 3. Remove screws (4) from upper triple clamp (5).
2. Remove visor (1).
3. Remove screw (3) and OEM clutch cable retainer.
4. Install clutch cable retainer (2) from kit.
5. Install screw (3). Tighten.
Torque: 4–5.4 N·m (35–48 in-lbs) Clutch cable retainer screw
6. Install visor (1).
7. Install screws (4). Tighten.
Torque: 4–5.4 N·m (35–48 in-lbs) Visor screw
1Visor
2Clutch cable retainer
3Screw
4Screw (2)
5Upper triple clamp
Figure 3. FXLR Visor
MODIFY
FXBB Cable Retainer
1. See Figure 4. Loosen screw (2).
2. Remove OE clutch cable retainer (1).
3. Trim down clutch cable retainer.
Length: 13 mm (½ in)
4. Install altered OE clutch cable retainer (1) in the orientation as shown.
5. Tighten screw (2).
Torque: 4–5.5 N·m (35–49 in-lbs) Clutch cable retainer screw
1Clutch cable retainer (altered and rotated)
2Screw
Figure 4. Altered Clutch Cable Retainer
FXLR and FXBB Turn Signals
FXBB
NOTE
The FXBB requires separate purchase parts. See Installation Requirements.
Do one turn signal at a time. Repeat procedure for other signal when finished.
1. See Figure 5. Loosen ball stud clamp (5) completely.
2. Remove and discard ball receptacle (6 or 7).
a. Left turn signal: Remove acorn nut (9) and lock washer (8) from mirror. Retain parts.
3. Loosen jam nut (3).
4. Remove ball stud (4) from turn signal (1 or 2).
5. Remove jam nut (3) from ball stud (4).
6. Remove and discard ball stud clamp (5).
7. Install front turn signal.
a. Install turn signal mount bracket (11 or 12), lock washer (8) and acorn nut (9) to mirror.
b. Adjust mirror and tighten nut (9).
Torque: 10.8–16.3 N·m (96–144 in-lbs) Mirror mounting nut
c. Install ball stud (4) to turn signal (13) and tighten locknut (3).
Torque: 5.6–7.9 N·m (50–70 in-lbs) Ball stud locknut
d. Verify turn signal is positioned properly.
e. Install and tighten screw lock (10).
Torque: 4–6.7 N·m (35–59 in-lbs) Ball stud locknut
FXLR
NOTE
The FXLR with installed Tall Risers and Moto Bar kits require separate purchase parts. See Installation Requirements.
Do one turn signal at a time. Repeat procedure for other signal when finished.
1. See Figure 5. Remove screw lock (10).
2. Loosen jam nut (3) and remove ball stud (4) from turn signal.
3. Remove and discard OE turn signal mount bracket.
a. Remove acorn nut (9) and lock washer (8) from mirror. Retain parts.
4. Install front turn signal.
a. Install turn signal mount bracket (11 or 12), lock washer (8) and acorn nut (9) to mirror.
b. Adjust mirror and tighten nut (9).
Torque: 10.8–16.3 N·m (96–144 in-lbs) Mirror mounting nut
c. Install ball stud (4) to turn signal (13) and tighten locknut (3).
Torque: 5.6–7.9 N·m (50–70 in-lbs) Ball stud locknut
d. Verify turn signal is positioned properly.
e. Install and tighten screw lock (10).
Torque: 4–6.7 N·m (35–59 in-lbs) Ball stud locknut
1FXBB Right OE turn signal
2FXBB Left OE turn signal
3Jam nut (2)
4Ball stud (2)
5Ball stud clamp (2)
6Right ball receptacle
7Left ball receptacle
8Internal tooth lock washer (1 OE and 1 separate purchase for FXBB only)
9Acorn nut (1 OE and 1 separate purchase for FXBB only)
10Screw lock (2) (separate purchase FXBB only)
11Right hand turn signal mount bracket (separate purchase)
12Left hand turn signal mount bracket (separate purchase)
13FXBB or FXLR OE Turn Signal
Figure 5. Turn Signal Brackets
INSTALL
    Once assembled, the mounting brackets (2 and 8) along with the clamps (4 and 10) should be spaced:
  • FXLR: 0.6 cm (0.25 in) from the bottom of the upper triple clamp.
  • FXBB and FXLRS: Installed against the bottom of the upper triple clamp.
1.
NOTE
Using an alcohol pad eases grommet installation and removes white shipping powder.
Install grommet (6) into left and right mounting brackets (2 and 8).
2. See Figure 6. Install left mounting bracket assembly.
a. Wipe clean the left fork (1) mounting area.
b. Loosely install left mounting bracket (2), clamp (4) and screws (5).
3. Install right mounting bracket assembly.
a. Wipe clean the right fork (11) mounting area.
b. Loosely install right mounting bracket (8), clamp (9) and screws (10).
4. Install hood bracket.
a. Adhere plastic washer (12) to each hole of hood bracket (7).
b. Align fastener holes in the left and right bracket (2 and 8) assemblies with hood bracket (7).
c. Make sure hood bracket (7) is centered on the headlamp.
d. Install tree fasteners (3) when all brackets are in proper alignment.
5. Install quarter fairing and check that headlamp is centered with the fairing opening.
a. Adjust brackets as needed.
b. Tighten fasteners to prevent movement.
c. Remove fairing.
6. Tighten screws (5 and 10).
Torque: 12.2–13.5 N·m (9–10 ft-lbs) Clamp screw
1Left fork
2Left mounting bracket
3Tree fastener (2)
4Left clamp
5Screw (2)
6Grommet (4)
7Hood bracket
8Right mounting bracket
9Right clamp
10Screw (2)
11Right fork
12Plastic washer (2)
Figure 6. Bracket Assembly