SMART TUNE PRO AUTOMATIC TUNING MODULE (ATM) KIT
J065082019-10-10
GENERAL
Kit Number
41000445
Models
For up to date certified model fitment information, see the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
Visit https://serviceinfo.harley-davidson.com for the latest instruction sheet.
These items are available at your local Harley-Davidson dealership.
  • Separate purchase of Exhaust Oxygen Sensor (Wide Band HO2) Bung Drill And Tap Tool Kit (Part No. 14900105) may be required for installation.
  • Separate purchase of Screamin' Eagle Pro Street Tuner (Part No. 41000008C) is required for this installation.
  • Screamin' Eagle Tuner Cable Kit (Part No. 41000018) is required for this installation.
  • 2017 and later Touring and Trike models: Separate purchase of Exhaust Oxygen Sensor (Wide Band HO2) Bung Drill And Tap Tool Kit (Part No. 14900105) is required for installation. An optional separate purchase of Screamin Eagle High-Flow Exhaust System with Street Cannon Mufflers (Part No. 64800059 or 64800062).
  • 2014-2016 Touring models: Separate purchase of Screamin Eagle High-Flow Exhaust System with Street Cannon Mufflers (Part No. 64800043 or 64800044) is required for this installation.
  • 2018 and later Softail models: Separate purchase of Wide Band O2 Sensor Wire Harness Extension Kit (Part No. 69201830) is required for this installation.
  • 2016-2017 Softail models: Separate purchase of Harley Davidson Head Pipe Assembly is required for this installation. Refer to Table 1.
  • 2016-2017 Softail models: Separate purchase of Wide Band O2 Sensor Wire Harness Extension Kit (Part No. 69201704) is required for this installation.
  • 2016-2017 Dyna Low Rider S (FXDLS) model: Separate purchase of Harley Davidson Head Pipe Assembly (Part No. 66884-09A) is required for this installation.
  • 2016-2017 Dyna Low Rider S (FXDLS) model: Separate purchase of Wide Band O2 Sensor Wire Harness Extension Kit (Part No. 69201704) is required for this installation.
  • 2014 and later Sportster models: Separate purchase of Wide Band O2 Sensor Wire Harness Extension Kit (Part No. 69201830) is required for this installation.
  • 2014 and later Sportster models: Separate purchase of 18 x 1.5 mm exhaust bungs from aftermarket source is required for this installation. Professional installation of exhaust bung is required.
Table 1. Softail Head Pipe
Model
Harley Davidson Part No.
FLSTF, FLSTFB, FLSTFBS
66779-07A
FLS, FLSS, FLSTN
65300-07A
FLSTC
66780-07, 66781-07
FXSB
66780-07, 66795-08
Table 2. Oxygen Sensor Bung Specifications
Oxygen Sensor Bung Requirements
Bung length minimum:
9 mm (0.360 in)
Bung length maximum:
13 mm (0.500 in)
Bung material:
300 Series stainless steel
Bung thread pitch:
M18 x 1.5
Sensor protrusion into exhaust pipe:
13 mm (0.500 in)
Installation notes:
Professional installation is required. Surfaces must be properly prepared. Weld should be complete around the bung and free of all leaks. Wideband sensor should be located as close as possible in the stock sensor location to ensure measured wideband AFR values correlate to factory sensors when operating in the same range. Bung should be located so that sensor has clearance and that wires do not touch the exhaust. When the bike is in the vertical position, the sensor should be mounted nearly horizontal but with the tip down to reduce risk of moisture on the sensor. Condensation in the exhaust can cause sensor damage.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
The Product Information Label contained in this kit is a requirement of the California Air Resource Board (CARB) emission regulation for all 2014 and later Touring models, 2016 and later Softail models, 2016 and later Dyna FXDLS and 2014 and Later Sportster models. Place the label on the right side of the frame directly beneath the VIN sticker. This label is not required outside the state of California.
Recalibrate ECM
NOTICE
You must recalibrate the ECM when installing this kit. Failure to properly recalibrate the ECM can result in severe engine damage. (00399b)
Kit Contents
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
INSTALLATION
Touring Wide Band HO2 Sensors
1. See service manual. Remove saddlebags.
2. See service manual. Remove main fuse.
3. See service manual. Remove seat.
4. Remove battery.
a. See Figure 1. Release ECM (1) from top caddy. Move out of the way.
b. If present, move purge solenoid (2) forward to release from top caddy.
c. Models with security system: Release HFSM antenna (3) from top caddy and move out of the way.
d. Release connectors (7) from anchors on top caddy.
e. Remove fasteners (5).
f. Cut cable straps (4). Move harnesses to allow more clearance for the top caddy.
g. Push top caddy forward to disengage front of caddy from front hold-down bracket. Lift and remove top caddy.
h. See Figure 2. Disconnect both battery cables, negative battery cable first.
i. Pull up battery strap to raise battery. When battery is extracted far enough to get a good grip, grasp battery and remove completely.
1ECM
2Purge solenoid
3HFSM antenna
4Cable straps
5Screws (2)
6Hold-down (not visible)
7Connectors (2)
Figure 1. Top Caddy
1Lifting strap
2Positive terminal
3Negative terminal
Figure 2. Battery Compartment
5. See service manual. Remove right front footboard and brackets from frame.
6.
NOTE
Note routing of oxygen sensor harness and placement of cable straps along the frame.
See Figure 3. Disconnect front (2) and rear (1) heated oxygen sensor (HO2) connectors.
1Rear oxygen sensor connector (black)
2Front oxygen sensor connector (grey)
Figure 3. Front and Rear Oxygen Sensor Location
7. See service manual. Remove exhaust system.
8. Exhaust pipe:
a. 2014-2016 models: Prepare Screamin Eagle High-Flow Exhaust System with Street Cannon Mufflers for HO2 sensor installation.
NOTE
No rework is required on Screamin Eagle High-Flow Exhaust System. Bungs accept wide band HO2 sensors.
b. 2017-later models: Rework exhaust pipe. Use Exhaust Oxygen Sensor (Wide Band HO2) Bung Drill And Tap Tool Kit (Part No. 14900105) to complete procedure or install Screamin Eagle High-Flow Exhaust System with Street Cannon Mufflers for HO2 sensor installation
9.
NOTE
  • Do not install sensors that have been dropped or impacted by other components. The sensing element may be damaged.
  • Replacement sensor assemblies have threads coated with anti-seize lubricant and a new gasket.
  • The electrical connector must be clean and free of any dielectric grease.
See Figure 4 , Figure 45 and Refer to Table 3. Install wide band heated oxygen sensors (2). Using Oxygen Sensor Socket (Part No. HD-48262-A) tighten to:
Torque: 40–60 N·m (29–44 ft-lbs)
Figure 4. Oxygen Sensor Locations (Inboard Side of Exhaust Pipes)
10.
NOTE
It is acceptable for the wide band sensor strain guide to make contact with the transmission cover.
If there is contact between the O2 sensor body and transmission cover, install a couple of washers or a spacer under the mid-frame exhaust clamp. Up to 0.200 in of spacer is acceptable.
See service manual. Install exhaust system with new exhaust gaskets.
11.
NOTE
ATM has four leads and a ground wire.
See Figure 5. With the ATM inside the battery box, route grey and black connector harnesses:
a. Start at front right corner of battery box area.
b. Slide grey or black connector harness (1) between the brake lines (2) and frame rail (3).
c. Slide connector harness along until it exits the battery box area and enters side cover area.
d. Repeat procedure for other connector harness.
1Black and grey harness connectors
2Brake lines
3Frame rail
Figure 5. Grey and Black Connector Harness Routing
12. See Figure 6 and Figure 9. Route the grey (3) and black (1) connector harness leads out behind the ABS control module (2) and connect to main harness. Color match connectors: black to black and grey to grey.
1Rear oxygen sensor connector (black)
2Front oxygen sensor connector (grey)
3ABS Control module
Figure 6. ATM Main Harness Connections
13. See Figure 7. Clean mounting surface with alcohol pad. Remove liner from adhesive backing and install dual lock tape to ATM. Remove liner from adhesive backing of dual lock tape and install ATM (1) to back of battery compartment.
14.
NOTE
Install cable straps as needed to secure harness. Make sure harness leads will not interfere when battery and top caddy are installed.
Install ATM with wire harness (2) facing right toward the inboard side of the frame.
1ATM Mounting location
2ATM with harness
Figure 7. ATM Mounting Location
15.
NOTE
  • Ground posts are located on right and left in front of battery compartment.
  • Grounds can be classified as either clean or dirty grounds. Clean grounds are identified by a (BK/GR) wire and are normally used for sensors or modules. The clean ground also has the negative battery cable chassis ground attached to it and is typically GND1.
See Figure 8. Route and connect ATM ground wire to clean ground post (2). Tighten to:
Torque: 6–10 N·m (50–90 in-lbs)
1Ground post (dirty ground)
2Ground post (clean ground)
Figure 8. Battery Box Ground Post Locations
16. See Figure 9. Front HO2 sensor (5, long harness lead):
a. From front sensor, route and secure O2 harness along the inboard side of the right frame downpipe. Install cable straps as needed.
b. Route and secure harness along inboard side of the lower frame toward the O2 sensor connector. Install cable straps as needed or use existing clamps and retainers.
c. Connect O2 sensor connectors.
17. Rear HO2 sensor (4, short harness lead):
a. From rear sensor, route and secure O2 harness along top of transmission (4). Install cable straps as needed.
b. From battery box area, route and secure ATM harness toward the O2 sensor connector. Secure with cable straps as needed.
c. Connect O2 sensor connectors.
1Rear oxygen sensor connector (black)
2Front oxygen sensor connector (grey)
3ABS Control module
4Rear O2 Sensor Harness Routing
5Front O2 Sensor Harness Routing
Figure 9. ATM Sensor Harness Routing
18. Make sure all harnesses and connectors are secured and not located in any hot zones.
19. See service manual. Install right front footboard and brackets to frame.
20. See service manual. Install battery, battery caddy and attach ECM.
21. See service manual. Install seat. After installing seat, pull up on the seat to verify that it is secure.
22. See service manual. Install main fuse.
23. See service manual. Install saddlebags.
24. See Figure 10. Use Screamin' Eagle Pro Street Tuner to complete installation. Download new ECM calibration when installing this kit. When selecting a calibration to download with the Screamin Eagle Pro Street Tuner, select Wideband (1) from the pull down menu for the O2 Sensor option. Refer to the Screamin' Eagle Pro catalog or contact a Harley-Davidson dealer for Screamin Eagle Pro Street Tuner details.
1Wideband O2 sensor selection
Figure 10. Wideband O2 Sensor Selection
2018 and Later Softail Wide Band HO2 Sensors
1. See service manual. Remove main fuse.
2. See service manual. Remove seat.
3. See service manual. Remove right side cover.
4. See service manual. Disconnect negative battery cable.
5.
NOTE
Make sure that the ATM module is not touching other components.
Position module so that the ground wire can reach the ground post.
See Figure 11. Position ATM module.
a. Position ATM module (2) on battery strap (1).
b. Mark location of module.
c. Remove ATM module.
1Battery strap
2ATM Module
Figure 11. Position Module
6. See Figure 12. See service manual. Remove battery strap (1).
1Battery strap
Figure 12. Battery Strap Location
7.
NOTE
Note routing of oxygen sensor harness and placement of cable straps along the frame.
See Figure 13. Disconnect rear heated oxygen sensor connector (1) from main harness.
1HO2 Sensor connector
2HO2 Sensor
Figure 13. Rear HO2 Sensor
8.
NOTE
Note routing of oxygen sensor harness and placement of cable straps along the frame.
See Figure 14. Disconnect front heated oxygen sensor connector (1) from main harness.
1HO2 Sensor connector
2HO2 Sensor
Figure 14. Front HO2 Sensor
9. See service manual. Remove exhaust pipe.
10. Drill and tap both oxygen sensor ports on exhaust system. Use Exhaust Oxygen Sensor (Wide Band HO2) Bung Drill And Tap Tool Kit (Part No. 14900105) to complete procedure.
11.
NOTE
  • Do not install sensors that have been dropped or impacted by other components. The sensing element may be damaged.
  • Replacement sensor assemblies have threads coated with anti-seize lubricant and a new gasket.
  • The electrical connector must be clean and free of any dielectric grease.
See Figure 15 , Figure 45 and Refer to Table 3. Install wide band heated oxygen sensors (2). Using Oxygen Sensor Socket (Part No. HD-48262-A) tighten to:
Torque: 40–60 N·m (29–44 ft-lbs)
Figure 15. Oxygen Sensor Locations (Inboard Side of Exhaust Pipes)
12. See service manual. Install exhaust pipe with new exhaust gaskets.
13. See Figure 12. Install battery strap.
a. Clean mounting surface with alcohol pad.
b. Remove liner from adhesive backing and install dual lock tape to ATM.
c. Remove liner from adhesive backing of dual lock tape and install to marked up area of battery strap.
d. Install ATM to battery strap.
e. Install battery strap.
14.
NOTE
Ground post is located under seat on left frame rail.
Make sure ground wire does not interfere with shock movement.
See Figure 16. Route and connect ATM ground wire to rear clean ground post (1). Tighten to:
Torque: 6–10 N·m (50–90 in-lbs)
1Ground post (clean ground)
2Ground post (dirty ground)
Figure 16. Frame Ground
15.
NOTE
Wire extension harness will have one end with a grey connector and the other end with a black connector.
Connect Wide Band O2 Sensor Wire Harness Extension Kit (Part No. 69201830) to ATM harness assembly. Color match connectors: grey to grey.
16. See Figure 17 and Figure 18. Route front HO2 harness with grey connector (4) out of battery compartment:
a. Locate main harness (6).
b. Route harness (4) with grey connector along main harness toward the front main harness connector (9).
c. Color match HO2 sensor connectors: black to black.
d. Secure harness to inboard side of right frame rail (8) with cable straps as needed.
17. Route black harness connector (2) to main harness. Color match connectors: black to black.
18. Front HO2 sensor (long harness lead):
a. Route front HO2 sensor connector harness (5) out of battery compartment.
b. Locate main harness (6).
c. Route harness (5) along main harness toward the front HO2 sensor (7).
d. Connect sensor connectors.
e. Secure harness to inboard side of right frame rail (8) with cable straps as needed.
19. Rear HO2 sensor (short harness lead):
a. Route harness along top of transmission.
b. Connect sensor connectors (3).
c. Secure harness with cable straps as needed.
1Ground wire
2Rear HO2 harness connector
3Rear HO2 sensor connector (short lead)
4Front HO2 harness connector (grey connector)
5Front HO2 sensor connector (long lead)
6Main harness
Figure 17. ATM Harness Routing
7Front HOS sensor connector (long lead)
8Right frame rail
9Front HO2 main harness connector
Figure 18. Front ATM Harness Routing (Parts removed for clarity)
20. Make sure all harnesses and connectors are secured and not located in any hot zones.
21. See service manual. Connect negative battery cable.
22. See service manual. Install right side cover.
23. See service manual. Install seat. After installing seat, pull up on the seat to verify that it is secure.
24. See service manual. Install main fuse.
25. See Figure 19. Use Screamin' Eagle Pro Street Tuner to complete installation. Download new ECM calibration when installing this kit. When selecting a calibration to download with the Screamin Eagle Pro Street Tuner, select Wideband (1) from the pull down menu for the O2 Sensor option. Refer to the Screamin' Eagle Pro catalog or contact a Harley-Davidson dealer for Screamin Eagle Pro Street Tuner details.
1Wideband O2 sensor selection
Figure 19. Wideband O2 Sensor Selection
2016-2017 Softail Wide Band HO2 Sensors
1. See service manual. Remove main fuse.
2. See service manual. Remove seat.
3. See service manual. Remove battery.
4. See Figure 20. See service manual. Remove battery caddy.
Figure 20. Non-Modified Softail Battery Caddy
5.
NOTE
Battery caddy must be modified to hold ATM. Do not cut completely through stiffening ribs. Cut only designated areas as instructed. Cutting more than required will lose structural integrity of battery caddy.
A die grinder with a cutting wheel is recommended.
See Figure 21 , Figure 22 , and Figure 23. Cut-off stiffening ribs (1 and 2) of caddy.
a. Position ATM module within battery caddy.
b. Mark outline of ATM harness on front. Also mark the depth on adjacent rib.
1Top stiffening rib
2Adjacent stiffening rib
Figure 21. Areas Highlighted To Be Cut Away
1Top stiffening rib
2Adjacent stiffening rib
Figure 22. Front of Caddy Cut Away
1Top stiffening rib
2Adjacent stiffening rib
Figure 23. Back of Caddy Cut Away
6.
NOTE
Note routing of oxygen sensor harness and placement of cable straps along the frame.
See Figure 24. Disconnect rear (1) heated oxygen sensor (HO2) connectors from main harness.
1Rear Oxygen Sensor Connector
Figure 24. Rear Oxygen Sensor Location
7.
NOTE
Note routing of oxygen sensor harness and placement of cable straps along the frame.
See Figure 25. Open front voltage regulator cover and disconnect front O2 sensor connector (1). Remove connector housing from caddy.
1Front Oxygen Sensor Connector
Figure 25. Front Oxygen Sensor Location
8. See service manual. Remove exhaust pipe.
9.
NOTE
  • Do not install sensors that have been dropped or impacted by other components. The sensing element may be damaged.
  • Replacement sensor assemblies have threads coated with anti-seize lubricant and a new gasket.
  • The electrical connector must be clean and free of any dielectric grease.
See Figure 26 , Figure 45 and Refer to Table 3. Install wide band heated oxygen sensors (2). Using Oxygen Sensor Socket (Part No. HD-48262-A) tighten to:
Torque: 40–60 N·m (29–44 ft-lbs)
Figure 26. Oxygen Sensor Locations (Inboard Side of Exhaust Pipes)
10. See service manual. Install exhaust pipe with new exhaust gaskets.
11. Install battery caddy with ATM. Adjust and reposition as needed.
12.
NOTE
Ground post is located in front of battery compartment.
See Figure 27. Connect ATM ground wire to clean ground post. Tighten to:
Torque: 6–10 N·m (50–90 in-lbs)
1Ground post (dirty ground)
2Ground post with negative battery cable (clean ground)
Figure 27. Battery Box Ground Post Locations
13. Connect Wide Band O2 Sensor Wire Harness Extension Kit (Part No. 69201704) to ATM harness assembly. Color match connectors: grey to grey.
14. See Figure 28. Route grey harness connector out of battery compartment:
a. Locate main harness (3).
b. Route harness with grey connector along main harness (2) toward the front main harness connector.
c. Color match connectors (1): grey to grey.
14.4. Secure harness to inboard side of the main harness with cable straps as needed.
1Grey connector
2Main harness routing
3Main harness
Figure 28. Harness Routing
15.
NOTE
Make sure harness leads will not interfere when battery and caddy are installed.
See Figure 24. Route black harness connector to main harness. Color match connectors: black to black.
16. See Figure 29. Front HO2 sensor (long harness lead):
a. Route harness connector out of battery compartment.
b. Locate main harness (2).
c. Route harness along main harness (1) toward the front O2 sensor connector.
d. Connect sensor connectors.
16.5. Secure harness to inboard side of main harness with cable straps as needed.
1Main harness routing
2Main harness
Figure 29. Harness Routing
17. Rear HO2 sensor (short harness lead):
a. Route harness along top of transmission to neutral switch area.
b. Connect sensor connectors.
c. Secure harness with cable straps as needed.
18. Make sure all harnesses and connectors are secured and not located in any hot zones.
19. See service manual. Install battery.
20. See service manual. Install seat. After installing seat, pull up on the seat to verify that it is secure.
21. See service manual. Install main fuse.
22. See Figure 30. Use Screamin' Eagle Pro Street Tuner to complete installation. Download new ECM calibration when installing this kit. When selecting a calibration to download with the Screamin Eagle Pro Street Tuner, select Wideband (1) from the pull down menu for the O2 Sensor option. Refer to the Screamin' Eagle Pro catalog or contact a Harley-Davidson dealer for Screamin Eagle Pro Street Tuner details.
1Wideband O2 sensor selection
Figure 30. Wideband O2 Sensor Selection
Dyna Wide Band HO2 Sensors
1. See service manual. Remove main fuse.
2. See service manual. Remove seat.
3. See service manual. Remove battery and battery box.
4.
NOTE
Note routing of oxygen sensor harness and placement of cable straps along the frame.
See Figure 31. Disconnect rear (1) heated oxygen sensor (HO2) connectors from main harness.
1Rear O2 Connector and Harness
Figure 31. Rear HO2 Sensor Location
5.
NOTE
Note routing of oxygen sensor harness and placement of cable straps along the frame.
See Figure 32. Open front electrical caddy cover and disconnect front O2 sensor connector (2). Remove connector housing from caddy.
1CKP Connector
2Front O2 Connector and Harness
Figure 32. Front HO2 Sensor Location
6. See service manual. Remove exhaust pipe.
7.
NOTE
  • Do not install sensors that have been dropped or impacted by other components. The sensing element may be damaged.
  • Replacement sensor assemblies have threads coated with anti-seize lubricant and a new gasket.
  • The electrical connector must be clean and free of any dielectric grease.
See Figure 33 , Figure 45 and Refer to Table 3.. In exhaust header part no. 64884-09A, install wide band heated oxygen sensors (2). Using Oxygen Sensor Socket (Part No. HD-48262-A) tighten to:
Torque: 40–60 N·m (29–44 ft-lbs)
Figure 33. Oxygen Sensor Locations (Inboard Side of Exhaust Pipes)
8. See service manual. Install exhaust pipe(s) with new exhaust gaskets.
9.
NOTE
ATM has four leads and ground wire. Install ATM with wire harness facing up the backbone of the frame.
See Figure 34. Clean mounting surface with alcohol pad. Remove liner from adhesive backing and install dual lock tape to ATM. Remove liner from adhesive backing of dual lock tape and install ATM to backbone of frame.
1ATM Mounting location
2Backbone of frame
Figure 34. ATM Mounting Location
10.
NOTE
  • Ground post is located under the seating area, on right and in upper rear of battery compartment.
  • Make sure harness will not interfere when battery and caddy are installed.
  • Ground: Grounds can be classified as either clean or dirty. Clean grounds are identified by a (BK/GN) wire and are normally used for sensors or modules.
See Figure 35. Route and connect ATM ground wire to clean ground post (1). Tighten.
Torque: 6–10 N·m (50–90 in-lbs)
1Ground post (clean ground)
2Ground post (dirty ground)
Figure 35. Battery Box Ground Post Locations
11. Connect Wide Band O2 Sensor Wire Harness Extension Kit (Part No. 69201704) to ATM harness assembly. Color match connectors: grey to grey.
12. See Figure 36. Route grey harness connector out of the back battery compartment:
a. Locate main harness (1) leading to harness caddy (2).
b. Route harness with grey connector along main harness caddy toward the front main harness connector.
c. Color match connectors (3): grey to grey.
12.4. Secure harness to inboard side of harness caddy (2) with cable straps as needed.
1Main harness
2Harness caddy
3Grey connector
Figure 36. Harness Caddy
13.
NOTE
Make sure harness leads will not interfere when battery and caddy are installed.
See Figure 31. Route black harness connector to main harness. Color match connectors: black to black.
14. See Figure 37. Front HO2 sensor (long harness lead):
a. Route harness connector out of the back battery compartment.
b. Locate main harness (1) leading to harness caddy (2).
c. Route harness along main harness caddy (2) toward the front O2 sensor connector.
d. Connect sensor connectors.
14.5. Secure harness to inboard side of harness caddy (2) with cable straps as needed.
1Main harness
2Harness caddy
Figure 37. Harness Caddy
15. Rear HO2 sensor (short harness lead):
a. Route harness along top of transmission to neutral switch area.
b. Connect sensor connectors.
c. Secure harness with cable straps as needed.
16. Make sure all harnesses and connectors are secured and not located in any hot zones.
17. See service manual. Install battery caddy and battery.
18. See service manual. Install seat. After installing seat, pull up on the seat to verify that it is secure.
19. See service manual. Install main fuse.
20. See Figure 38. Use Screamin' Eagle Pro Street Tuner to complete installation. Download new ECM calibration when installing this kit. When selecting a calibration to download with the Screamin Eagle Pro Street Tuner, select Wideband (1) from the pull down menu for the O2 Sensor option. Refer to the Screamin' Eagle Pro catalog or contact a Harley-Davidson dealer for Screamin Eagle Pro Street Tuner details.
1Wideband O2 sensor selection
Figure 38. Wideband O2 Sensor Selection
Sportster Wide Band HO2 Sensors
Pending Regulatory Approval. Refer to product information at: www.harley-davidson.com/shop/screamin-eagle
1. See service manual. Remove main fuse.
2. See service manual. Remove seat.
3. See service manual. Remove left side cover.
4. See service manual. Disconnect negative battery cable.
5.
NOTE
Note routing of oxygen sensor harness and placement of cable straps along the frame.
See Figure 39. Disconnect rear heated oxygen sensor connector (3) from main harness.
1Rear HO2 Sensor
2Cover clip
3HO2 Sensor connector
Figure 39. Rear HO2 Sensor
6.
NOTE
Note routing of oxygen sensor harness and placement of cable straps along the frame.
See Figure 40. Disconnect front heated oxygen sensor connector (3) from main harness.
1Front HO2 Sensor
2Frame clip
3HO2 Sensor connector
Figure 40. Front HO2 Sensor
7. See service manual. Remove exhaust pipe.
8.
NOTE
A professional welding or metal fabrication shop is highly recommended for removing and installing the oxygen sensor bung.
Remove or plug both stock oxygen sensor bungs from exhaust system.
9.
NOTE
Refer to Table 2. Oxygen Sensor Bung Specifications at the beginning of this instruction sheet.
Install new oxygen sensor bungs into exhaust system.
10.
NOTE
  • Do not install sensors that have been dropped or impacted by other components. The sensing element may be damaged.
  • Replacement sensor assemblies have threads coated with anti-seize lubricant and a new gasket.
  • The electrical connector must be clean and free of any dielectric grease.
See Figure 41 , Figure 45 and Refer to Table 3.. Install wide band heated oxygen sensors (2). Using Oxygen Sensor Socket (Part No. HD-48262-A) tighten to:
Torque: 40–60 N·m (29–44 ft-lbs)
Figure 41. Oxygen Sensor Locations (Inboard Side of Exhaust Pipes)
11. See service manual. Install exhaust pipes with new exhaust gaskets.
12. See Figure 43. Install ATM module (5).
a. Clean mounting surface with alcohol pad.
b. Remove liner from adhesive backing and install dual lock tape to ATM.
c. Remove liner from adhesive backing of dual lock tape and install ATM to side of battery strap.
13.
NOTE
See Figure 42. Ground post (1) is located behind the primary cover on left crankcase half.
Verify negative battery cable is mounted to this grounding point.
See Figure 43. Route and connect ATM ground wire (6) to clean ground post. Tighten to:
Torque: 6–10 N·m (50–90 in-lbs)
1Ground post (clean ground)
Figure 42. Sportster Ground
14.
NOTE
Wire extension harness will have one end with a grey connector and the other end with a black connector.
Connect Wide Band O2 Sensor Wire Harness Extension Kit (Part No. 69201830) to ATM harness assembly. Color match connectors: grey to grey.
15. Route front HO2 grey harness connector out of the back battery compartment:
a. Locate ABS harness (7).
b. Route harness with grey connector (1) along ABS harness toward left frame rail.
c. Route harness (1) along the frame toward the front main harness connector.
d. Color match connectors: black to black.
e. Secure harness to inboard side of left frame rail with cable straps as needed.
16. Route rear HO2 black harness connector (4) and connect to main harness.
a. Color match connectors: black to black.
17. Front HO2 sensor (long harness lead):
a. Route front HO2 sensor connector harness (2) out of the back battery compartment.
b. Locate ABS harness (7).
c. Route harness (2) along ABS harness toward left frame rail.
d. Route harness (2) along left frame rail toward the front O2 sensor connector.
e. Connect sensor connectors.
f. Secure harness to inboard side of left frame rail with cable straps as needed.
18. Rear HO2 sensor (short harness lead):
a. Route rear HO2 sensor connector harness (4) along top of crankcase.
b. Connect sensor connectors.
c. Secure harness with cable straps as needed.
1Front HO2 harness connector (grey connector)
2Front HO2 sensor connector (long lead)
3Rear HO2 sensor connector (short lead)
4Rear HO2 harness connector
5ATM module
6Ground wire
7ABS harness
Figure 43. ATM Harness Routing (place holder)
19. Make sure all harnesses and connectors are secured and not located in any hot zones.
20. See service manual. Connect negative battery cable.
21. See service manual. Install seat. After installing seat, pull up on the seat to verify that it is secure.
22. See service manual. Install left side cover.
23. See service manual. Install main fuse.
24. See Figure 44. Use Screamin' Eagle Pro Street Tuner to complete installation. Download new ECM calibration when installing this kit. When selecting a calibration to download with the Screamin Eagle Pro Street Tuner, select Wideband (1) from the pull down menu for the O2 Sensor option. Refer to the Screamin' Eagle Pro catalog or contact a Harley-Davidson dealer for Screamin Eagle Pro Street Tuner details.
1Wideband O2 sensor selection
Figure 44. Wideband O2 Sensor Selection
SERVICE PARTS
Figure 45.
Table 3. Kit Contents
Item
Description (Quantity)
Part Number
1
Wideband O2 Control Module Assembly
41000445
2
Oxygen Sensor, Wideband (2)
32700098
3
CARB E.O. Label
Not Sold Separately
4
Dual Lock Fastener (2)
Not Sold Separately
5
Cable Strap (8)
Not Sold Separately
6
Harness, Extension, Front Wide Band OS Sensor
(Sportster and 2018 and later Softail)
69201830