HANDLEBAR GRIPS
941001782020-08-24
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
Time
56100479
Safety Glasses, Torque Wrench
1 h
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Handlebar Grips
Table 2. Kit Contents: Handlebar Grip Components
Item
Qty
Description
Part No.
Notes
1
1
Grip, left
56100480
2
1
Grip, right
56100481
3
6
Set screw
10201108
NOTE
Verify that all contents are present in the kit before installing or removing items from vehicle.
GENERAL
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only)
Verify that the most current version of the instruction sheet is used. It is available at: www.harley-davidson.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
A solution of 70% isopropyl alcohol and 30% water is needed. This solution temporarily reduces the adhesive properties of the two-sided tape.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
REMOVE
Left Side Grip
1. See Figure 2. Remove the left switch housing. See the service manual.
2. Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife.
NOTE
Thoroughly clean handlebar to remove all residual adhesive.
NOTE
Do not install the adhesive tape now.
3. Remove tape and adhesive residue from the handlebar.
INSTALL
Left-side Grip
1. Install the left switch housing. See the service manual.
NOTE
See Figure 1. for proper orientation of grip.
2. To understand the correct orientation of the left side grip: Position the new left grip so the lines on the grip are toward the rider and front of the vehicle. See Figure 1. The lines on the grip are vertical.
3. Test fit the grip without the adhesive tape. Ensure that the grip can fully seat without contacting the switch housing. Remove the left side hand grip.
1Grip, left
2Screw (2)
3Upper housing
4Lower housing
5Adhesive tape
6Set screw (4)
Figure 2. Left Hand Grip
1Handlebar
21/4 in measurement
3Center line of handlebar
4Short side, 4 in
5Adhesive tape
6Long side, 6 in
Figure 3. Left Hand Grip
1Handlebar
2Adhesive tape
3Paper backing, bottom
4Adhesive tape completely wrapped
Figure 4. Handlebar and Adhesive Tape
Adhesive Tape
1. To ease installation. See Figure 3. Make a mark 1/4 in (2) from the end of the handlebar. Keep the adhesive tape along this line while applying. To aid in alignment make a mark (3) straight along handlebar.
2. See Figure 4. Remove the paper from the bottom side (3) of the adhesive tape (2).
3. See Figure 3. Align one of the short sides (4) of the adhesive tape (5) with line (3).
NOTE
Once the isopropyl alcohol and water solution has been applied to the tape there is a limited time to complete the installation. Verify that the switch housing and grip are oriented correctly before proceeding.
4. See Figure 4. Begin to apply the adhesive tape to the handlebar. Do not wrinkle the adhesive tape. Remove the top side of the paper (4) to prevent overlapping the paper while wrapping the handlebar. Fully wrap the adhesive tape around the handlebar.
5. Spray the tape liberally with the solution of 70% isopropyl alcohol and 30% water. The solution will temporarily reduce the adhesive property so the grip can be installed. After the solution is applied, you have about 1 minute to work before the adhesive begins to harden. Do not move the hand grip for 4 hours after installation to allow the adhesive tape to cure.
NOTE
Do not move the hand grip for 4 hours after installation to allow the adhesive tape to cure.
6. Tighten grip set screws.
Torque: 2–2.5 N·m (18–22 in-lbs)
REMOVE
Right Side Grip
NOTICE
Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a)
1. Remove switch housings and the right side grip (throttle twist grip). See service manual
INSTALL
1. Install switch housings and grip. See service manual.
NOTE
See Figure 1. for proper orientation of grip.
2. Adjust the switch housing and brake hand control position for rider comfort.
3. Secure first the upper, then the lower handlebar clamp screws. Tighten.
Torque: 6.8–6.9 N·m (5–5 ft-lbs)
4. Secure first the lower, then the upper switch housing screws. Tighten.
Torque: 2–2.5 N·m (18–22 in-lbs)
WARNING
Before starting engine, be sure throttle control will snap back to idle position when released. A throttle control that prevents engine from automatically returning to idle can lead to loss of control, which could result in death or serious injury. (00390a)
5. Verify that the right grip/throttle sleeve rotates and returns freely and does not bind on the handlebar or switch housing.
End Cap
INSTALL
1. Install end caps on left and right side grips.
a. Insert the end cap into the end of the grip.
b. Orient the bar and shield logo so that it is horizontal.
c. Install 2 set screws. Tighten.
Torque: 2–2.5 N·m (18–22 in-lbs)