RIDER FOOTBOARD KIT
J065122020-12-15
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
Time
Footboard Kits: 50500869, 50500872,50501294A, 50501295A
Insert Kits: 50500928, 50500929, 50500930, 50500931
Safety Glasses, Torque Wrench
1 h
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Rider Footboard Components
Table 2. Kit Contents: Rider Footboard Components
Item
Qty
Description
Part No.
Notes
1
4
Screw
10200658
Torque: 2.26 - 3.39 Nm (20 - 30 in-lbs)
2
2
Insert, footboard
Not sold separately
3
1
Footboard, left side (not shown)
Not sold separately
1
Footboard, right side
Not sold separately
4
2
Wear peg, Kits 50500869, 50500872
50501013
2
Wear peg, Kits 50501294, 50501295
50501296A
5
4
Screw
10200659
Torque: 1.8 - 2.26 Nm (15.9 - 20 in-lbs)
6
4
Screw, Kits 50501294, 50501295
10500137
Torque: 6.8 - 9 Nm (60 - 80 in-lbs)
Items mentioned in text, but not included in kit.
A
2
Nut
NOTE
Verify all contents are present in the kit before installing or removing items from vehicle.
GENERAL
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Verify that the most current version of the instruction sheet is used. It is available at: www.harley-davidson.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
NOTE
There may be decreased access to the jiffy stand tab on Softail models.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
REMOVE
1. Kits 50500869, 50500872: See Figure 2. Remove footboard.
a. Remove e-clip (3), clevis pin (1), and torsion spring (2).
b. Save hardware for installation.
2. Kits 50501294, 50501295: See Figure 1. Remove footboard.
a. Remove shoulder bolt (6) and nut (A).
b. Retain nuts (A) for reuse.
INSTALL
Kits 50500869, 50500872:
1. Clean and inspect footboard brackets. Replace if worn, rusted or damaged.
2. See Figure 2. Install footboard.
a. Insert short end of torsion spring (2) into forward most hole in footboard.
b. While holding torsion spring (2) in place, install footboard and spring onto mounting bracket.
c. Install clevis pin (1).
d. Install e-clip (3).
1Clevis pin
2Torsion spring
3E-clip
Figure 2. Rider Footboard Installation
Kits 50501294, 50501295:
1. Clean and inspect footboard brackets. Replace if worn, rusted or damaged.
2. See Figure 1. Install footboard.
a. Install new shoulder bolt (6) and footboard.
b. Apply threadlocker and install nut (A). Tighten.
Torque: 6.8–9 N·m (60–80 in-lbs)
LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
3. Check that foorboard pivots freely on clevis pin (1).
4. Repeat for opposite side.
NOTE
Avoid contacting chrome surfaces with abrasive materials (stones, sand, etc.) as damage will result.
INSTALL OR REPLACE INSERT
1. Remove screws (1).
2. Replace insert (2).
3. Apply threadlocker and install screws (1). Tighten.
Torque: 2.26–3.39 N·m (20–30 in-lbs)
LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
REPLACE WEAR PEG
1. Remove screws (5).
2. Replace wear peg (4).
3. Apply threadlocker and install screws (5). Tighten.
Torque: 1.8–2.26 N·m (15.9–20.0 in-lbs)
LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)