KEYSTONE AUXILIARY LED RUN/BRAKE/TURN LIGHT
941000202021-01-11
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
Time
67801080, 67801082
Safety Glasses, Torque Wrench, Isopropyl Alcohol
1 h
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Keystone Auxiliary LED Run/Brake/Turn Light Kit Components
Table 2. Kit Contents: Keystone Auxiliary LED Saddlebag Run/Brake/Turn Light Kit Components
Item
Qty
Description
Part No.
Notes
1
1
Harness
69202325
2
2
Sub-assembly, red
67801073
Sub-assembly, smoke
67801074
3
1
Bracket, Sub-assembly, left
67801157
Bracket, Sub-assembly, right
67801158
4
6
Cable strap
10065
5
5
Cable strap
10126
6
6
Wire retainer w/ adhesive pad
11769
NOTE
Verify that all contents are present in the kit before installing or removing items from vehicle.
GENERAL
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Verify that the most current version of the instruction sheet is used. It is available at: www.harley-davidson.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
NOTE
  • Ambient temperature must be between 21-38°C (70-100°F) for proper adhesion. Do not install under 10°C (50°F).
  • Allow at least 24 hours after installation before exposing area to vigorous washing, strong water spray or extreme weather.
  • Adhesive bond will increase to maximum strength after about 72 hours at normal room temperature.
PREPARE
1. Remove main fuse. See service manual.
2. Remove seat. See service manual.
3. Remove saddlebags. See service manual.
LIGHTS
REMOVE
1. Remove nut (5). Do not remove screw (4). Screw is an aid in locating backplate.
INSTALL
NOTE
Lights are identified with an (L) for left or (R) for right, imprinted on lens.
1. See Figure 2. With adhesive backing (2) still in place, test fit the Run/Brake/Turn Auxiliary Light.
NOTE
Surface where tape is applied must be cleaned. Failure to clean this area results in a faulty installation.
2. Clean area on casting (5) where tape is installed with a mixture of equal parts of isopropyl alcohol and distilled water.
3. Allow to dry completely.
4. Remove adhesive tape backing (2).
5. Position bracket (1) over screw (4).
6. Apply firm sliding pressure in tape areas.
7. Install nut (6) on screw (4). Tighten.
Torque: 20.3–27.1 N·m (15–20 ft-lbs)
8. Install LED light (3).
9. Install screws (7). Tighten.
Torque: 0.9 N·m (8 in-lbs)
NOTE
Use caution when tightening screws (7). Over tightening screws will crack the LED light.
10. Repeat previous steps for other side.
1Bracket
2Adhesive tape
3LED Light
4Screw
5Casting
6Nut
7Screw (2)
Figure 2. Run/Brake/Turn Auxiliary Lights
MODULE/WIRING
INSTALL
1. See Figure 3. Route rear lighting Y-harness and left saddlebag light harness (4 and 6-pin connectors) back along left upper frame (5).
2. Route right saddlebag light harness (4 and 6-pin connectors) along right upper frame (6).
3. Separate rear lighting connector [7] (3,4).
4. Attach 6-terminal connectors from Y-harness to each separated connector half.
5. Secure new harnesses along inside of upper frame tubes with two cable straps per side.
6. Cross to outside of frame rear of upper shock absorber attachment point.
1FLHX, FLHXS, FLTRX, FLTRXS, FLTRXSE
2FLHR, FLHRSE, FLHTCU, FLHTCUL, FLHTK, FLHTKL, FLHTKSE, FLTRUSE, FLTRU
3Rear lighting, connector - rear half
4Rear lighting connector - main harness half
5Path of wye harness and left saddlebag light harness
6Path of right saddlebag light harness
Figure 3. Mate Connectors
COMPLETE
WARNING
Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a)
1. Install saddlebags. See service manual.
2. Install seat. After installing seat, pull up on the seat to verify that it is secure. See service manual.
3. Install main fuse. See service manual.
4. Turn ignition on.
5. Test rear stop/tail/turn and hazard lighting functions.