FAIRING SPEAKER HARNESS INSTALL KIT (PN 76001100)
941002692021-02-04
GENERAL
NOTE
The newly installed audio system and speakers will not play audio unless it is configured using the Harley-Davidson mobile app or by an authorized Harley-Davidson dealership.
Table 1.
Harley-Davidson Audio Powered by Rockford FosgateĀ®
Kit
QR Code
76001100
N/A
NOTE
The various generations of speakers, amplifiers and wiring for Harley-Davidson vehilces were not designed or tested to work together. Please consult your dealership to ensure optimal performance and compatibility.
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Ensure you are using the most current version of the instruction sheet which is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
Download Harley-Davidson mobile app.
This harness is for use on 2014 and later CVO FLHTKSE and 2015-2016 FLTRUSE models Harley-Davidson audio systems.
    These items are available at your Harley-Davidson dealership.
  • Separate purchase of Harley-Davidson Primary Amplifier and Dongle Kit (Part No. 76000997) is required for this installation.
  • Separate purchase of Harley-Davidson Primary Amplifier Installation Kit (Part No. 76000974 or 76001045) is required for this installation.
  • Separate purchase of Harley-Davidson Stage 1 or 2 Speaker Kit (Part No. 76000980, 76000981, 76000982 or 76000983) is be required for this installation.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
Installation by a technician at a Harley-Davidson dealership is recommended.
Kit Contents
See Figure 8 and Table 2.
PREPARE
WARNING
To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
NOTE
This instruction sheet references service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
1. Remove left and right saddlebags.
2. Remove left and right side covers.
3. Remove main fuse.
NOTE
Models with security: Disable security system.
4. Remove seat.
5. Remove fuel tank.
6. Remove wire trough cover.
7. Remove windshield.
8. Remove outer fairing.
a. For fixed fairing models, remove headlamp.
INSTALL
1. Connect fairing speaker harness.
a. See Figure 2. Disconnect the amplifier harness connector (1).
b. Remove stock amplifier and amplifier mounting brackets.
c. Fork mounted faring models: Install the four screws back into the top of the radio.
d. Connect amplifier connector (1) to amplifer bypass connector (2).
e. Route harness though inner fairing near the steer head.
2. Route harness through backbone wire trough.
3. Route [349A] toward right side cover and primary amplifier external harness.
4. Connect [349A] to [349B] of the primary amplifier external harness.
1[349A] Audio In/Out (channel 1 and 2)
2[149] Amplifier bypass connector
Figure 1. Fairing Speaker Harness
1[149] Amplifier connector
2[149] Amplifier bypass connector
Figure 2. Fork Mounted Fairing Shown, Fixed Fairing Similar
COMPLETE
NOTE
To prevent possible damage to the sound system, verify that the ignition is OFF before installing the main fuse.
1. Install main fuse.
2.
NOTE
Before installing outer fairing, check that speakers are operating correctly. Understand that buzzing, squeaks and rattles may be heard until outer fairing is installed.
Turn ignition ON, but do not start the vehicle.
3. Make sure that all speakers are working and front/rear fader function is operating correctly. If not, check speaker wiring.
4. Install outer fairing.
5. Install windshield.
6. Install wire trough cover.
7. Install fuel tank.
8. Install seat.
9. Install left and right side covers.
10. Install left and right saddlebags.
APP SETUP
1. Unresolved graphic link Accessing your audio system.
a. Pair device (1) to system.
b. Access app menus (2) to setup vehicle sound system.
1Add bluetooth device
2Configure audio system
Figure 3. System Access
2. Unresolved graphic link Main menu screen.
a. Main menu icon (1).
b. Reset or change security personal identification number (PIN) (2).
c. Edit and rename your system (3).
d. Customize main menu with your bike picture (4).
e. Bluetooth connection indicator. Slash through symbol indicates: Not Connected (5).
1Main menu
2Change security pin
3Rename system
4Customize main menu picture
5Bluetooth connection indicator
Figure 4. Main Menu
3. Unresolved graphic link Setup menu screen.
a. Setup menu icon (1).
b. Use to scan QR code (2) on iSheet.
c. Manual setup for Stage 1 or 2 speakers, speaker location and white noise to assign speaker locations.
1Setup menu
2QR Code scan
3Manual setup
Figure 5. Setup Menu
4. Unresolved graphic link Equalizer setup screen.
a. Equalizer setup icon (1)
b. Tune 7-Band equalizer (2) frequencies.
c. Custom or preset equalizer selections (3).
1Equalizer menu
27-Band equalizer
3Equalizer preset selection
Figure 6. Equalizer Menu
5. Unresolved graphic link Diagnostic menu screen.
a. Diagnostic menu icon (1) displays sound system status.
b. Open the speaker testing screen (2).
c. Refreshes speaker and amplifier status (3) after component repair.
d. Select speaker for white noise (4) test and functionality.
e. Return to diagnostic menu screen (5).
1Diagnostic menu
2Speaker test screen
3Refresh status
4Select a speaker to play white noise
5Finish and return to diagnostic menu
Figure 7. Diagnostic Menu
SERVICE PARTS
Figure 8. Service Parts, Amplifier Installation Kit
Table 2. Service Parts
Item
Description (Quantity)
Part Number
1
Fairing wire harness
Not sold separately
2
Cable strap (8)
10006