DERBY COVER KIT
J066042021-08-03
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
25700934, 25700958, 25700959, 25700960, 25700961, 25700962, 25700963, 25700964, 25700965, 25700966, 25700967, 25700968, 25700969, 25700970, 25700971, 25700972, 25700973, 25700976, 25701023, 25701063, 25701088, 25701407, 25701408, 25701175, 25701177, 25701179
Safety Glasses, Torque Wrench
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Derby Cover Components
Table 2. Kit Contents: Derby Cover Components
Item
Qty
Description
Part No.
Kit Number
1
1
Clutch cover
Not sold separately
2
5
Washer, flat
10300155
Kits: 25700958, 25700959, 25700965, 25700966, 25700969, 25700973, 25700961, 25700962, 25701063, 25701175, 25701408
5
Washer, flat, black oxide
10300161
Kits: 25700963, 25700964, 25700967, 25700970, 25700971, 25700972, 25700976, 25701023, 25701088, 25701407, 25701177
3
5
Screw, button head, TORX®, chrome
10200672
Kits: 25700958, 25700959, 25700969, 25700973, 25700961, 25701063, 25701408, 25701175
4
Screw, button head, TORX®, chrome
Kit: 25700962
1
Screw, button head, TORX®, chrome
10200714
Kit: 25700962
4
Screw, button head, TORX®, black zinc
10200698
Kits: 25700963, 25700964, 25701023, 25701088
5
Screw, button head, TORX®, black zinc
Kits: 25700971, 25701177, 25701407
1
Screw, button head, TORX®, black zinc
10200715
Kits: 25700963, 25700964
5
Screw, button head, TORX®, black oxide
10200699
Kits: 25700967, 25700970, 25700972, 25700976
6
Screw, socket head, stainless
10200659
Kits: 25700965, 25700966
5
Screw, socket head, zinc
10200700
Kits: 25700965, 25700966
NOTE
Verify all contents are present in the kit before installing or removing items from vehicle.
GENERAL
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Ensure that the most current version of the instruction sheet is used. It is available at: www.harley-davidson.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
REMOVE
1. Remove Original Equipment (OE) screws and washers. Set aside.
2. Inspect quad ring gasket. Replace if necessary.
3. Verify quad ring is properly seated in groove of primary cover.
INSTALL
NOTE
  • Kit Number 25701063: Bare Aluminum Wheel Protectant Wipes (Part No. 93600063) can be applied to "RideFree" text for added corrosion protection.
  • Kit Numbers 25700962, 25700963 and 25700964: One longer screw goes into the 2 o'clock position.
If reusing OE screws, clean threads of screw and chase hole. Apply LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) to screws.
1. See Figure 1. Install new cover (1).
2. Install washers (2) and screws (3).
3. See Figure 2. Tighten screws in a star pattern.
Torque: 2.8–3.9 N·m (25–35 in-lbs)
a. Kits: 25700965 and 25700966. Tighten screws (Part No. 10200659).
Torque: 1.69–2.25 N·m (15–20 in-lbs)
Figure 2. Clutch Cover Tightening Sequence
NOTE
PN 25701179 uses the OE screws, which are PN 10200644. Apply the 2.8-3.9 Nm torque.