FOOTPEG KIT
J063352021-08-02
GENERAL
Kit Number
50500533, 50500535, 50500536, 50500540, 50500655, 50500678, 50501895, 50501896, 50501897, 50502111, 50502112, 50502113
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Kit Contents
See Figure 3 and Table 1.
Installation Requirements
Loctite® 243 Threadlocker and Sealant - Blue (Part No. 99642- 97) to install replacement wear tips.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer.
INSTALL
1. Remove hardware fastening stock footpeg to vehicle footpeg support. Save hardware for installation of new footpegs.
2. Remove existing footpegs and spring washers. Note orientation of, and save, spring washers for installation.
NOTE
See Figure 1. When installing footpeg support mount on vehicle footpeg support make sure spring washer (1) is positioned inside of footpeg support with square edge toward inside of support.
3. Install new footpeg mount in reverse order of stock footpeg mount removal. Place a spring, along with mount end of footpeg, inside slots of footpeg supports.
NOTE
Secure each footpeg mount and spring washer with screw and locknut removed earlier. Tighten the locknuts to 29 N·m (21 ft-lbs).
WARNING
Footrests must fold up and toward rear of motorcycle if struck. Failure to set footrests to fold up and back could result in death or serious injury. (00366a)
4. See Figure 1. For each footpeg, position footpeg as desired, then secure adjusting screw (1). Tighten.
Torque: 29 N·m (21 ft-lbs)
5. Empire footpegs install with wider section of footpeg facing forward on vehicle.
Wear Tip Replacement
NOTE
See service manual for wear tip orientation.
1. See Figure 2. Remove existing wear tip from footpeg.
2. Apply 2 or 3 drops of threadlocker to threads of new wear tip and install to footpeg.LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
3. Secure wear tip. Tighten.
Torque: 6–9 N·m (4–7 ft-lbs)
1Spring washer
2Straight edge
3Footpeg mount support
Figure 1. Footpeg Spring Washer Install
Figure 2. Footpeg Adjusting Screw
Service Parts
Figure 3. Service Parts
Table 1. Service Parts Table
Item
Description (Quantity)
Part Number
1
Rubber foot peg (1)
Not sold separately
2
Socket head cap screw (1)
Not sold separately
3
Foot peg base (1)
Not sold separately
4
Foot peg wear peg (1)
50500514
5
Chrome medallion grip (2)
14100879
6
Long black foot peg mount (1)
Not sold separately
Figure 4. Service Parts: Empire Collection
Table 2. Service Parts: Empire Collection
Kit
Item
Description (Quantity)
Part Number
50501895
1
Footpeg, Rider, Left, Chrome
50501883
2
Footpeg, Rider, Right, Chrome
50501892
50501896
1
Footpeg, Rider, Left, Black
50501884
2
Footpeg, Rider, Right, Black
50501893
50501897
1
Footpeg, Rider, Left, Machine Cut
50501885
2
Footpeg, Rider, Right, Machine Cut
50501894
50502111
3
Footpeg, Passenger, Left, Chrome
50502053
4
Footpeg, Passenger, Right, Chrome
50502054
50502112
3
Footpeg, Passenger, Left, Black
50502055
4
Footpeg, Passenger, Right, Black
50502050
50502113
3
Footpeg, Passenger, Left, Machine Cut
50502051
4
Footpeg, Passenger, Right, Machine Cut
50502055