SIGNATURE LED SADDLEBAG RUN/BRAKE/TURN LIGHT
941000192021-08-20
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
Time
67801023 (Red), 67801024 (Smoke)
Safety Glasses, Torque Wrench, Isopropyl Alcohol, Grease Pencil
1 h
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Signature LED Saddlebag Run/Brake/Turn Light Kit Components
Table 2. Kit Contents: Signature LED Saddlebag Run/Brake/Turn Light Kit Components
Item
Qty
Description
Part No.
Notes
1
1
Harness, red, Kit 67801023
69202326
Harness, smoke, Kit 67801024
69202416
2
1
Sub-assembly, left, red
Not Sold Separately
Sub-assembly, left, smoke
Not Sold Separately
3
1
Sub-assembly, right, red
Not Sold Separately
Sub-assembly, right, smoke
Not Sold Separately
4
4
Cable strap
Not Sold Separately
5
4
Cable strap
Not Sold Separately
6
4
Clip, nylon
Not Sold Separately
7
4
Wire retainer w/ adhesive pad
Not Sold Separately
NOTE
Verify that all contents are present in the kit before installing or removing items from vehicle.
GENERAL
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Verify that the most current version of the instruction sheet is used. It is available at: www.harley-davidson.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
NOTE
  • Ambient temperature must be between 21-38 °C (70-100 °F) for proper adhesion. Do not install under 10 °C (50 °F).
  • Allow at least 24 hours after installation before exposing area to vigorous washing, strong water spray or extreme weather.
  • Adhesive bond will increase to maximum strength after about 72 hours at normal room temperature.
PREPARE
1. Remove main fuse. See service manual.
2. Remove seat. See service manual.
LIGHTS
REMOVE
NOTE
Reflectors on some Canadian models are installed below saddlebag lids. These reflectors must be removed. To remain in compliance, install reflectors directly below Electro Glo LED saddlebag run/brake/turn lights.
1. Remove saddlebag reflectors if installed.
2. Clean saddlebag in area of installation with 50:50 mix of isopropyl alcohol and water.
3. Allow to dry completely.
INSTALL
NOTE
Lights are identified with an (L) for left or (R) for right, imprinted on lens.
1. Position light approximately 3.2 mm (1/8 in) below bottom edge of saddlebag lid when closed.
2. Use a grease pencil to mark location.
3. Remove adhesive backing from light assembly.
4. Install light using marks made earlier as a guide.
5. Apply firm even pressure.
6. Do not use extreme pressure over lens area.
7. If equipped, install saddlebag reflectors directly below newly installed saddlebag run/brake/turn lights.
8. Remove saddlebag. See owner's manual.
9. See Figure 2. Route wiring forward along vehicle side of saddlebag.
a. Clean attachment areas with a 50:50 mix of rubbing alcohol and water.
b. Secure wiring to saddlebag surface with two wire retainers (1) and cable straps (2).
10. Repeat for remaining saddlebag light.
Figure 2. Saddlebag Harness Routing
MODULE/WIRING
INSTALL
1. See Figure 3. Route rear lighting Y-harness and left saddlebag light harness (3-way socket connector) back along left upper frame (5).
2. Route right saddlebag light harness (3-way pin connector) along right upper frame (6).
3. Separate rear lighting connector [7] (3,4).
4. Attach 6-terminal connectors from Y-harness to each separated connector half.
5. See Figure 4. Secure new harnesses along inside of upper frame tubes with two cable straps per side.
6. Cross to outside of frame rear of upper shock absorber attachment point.
7. Install saddlebags. See owner's manual.
8. Connect saddlebag light connectors during installation.
1FLHX, FLHXS, FLHX SHRINE
2FLHR, FLHTCU, FLHTCU-TC, FLHTK, FLHTK SHRINE
3Rear lighting connector - rear half
4Rear lighting connector - main harness half
5Path of wye harness and left saddlebag light harness
6Path of right saddlebag light harness
Figure 3. Mate Connectors
1Harness
2Existing wire bundle
Figure 4. Install Module
COMPLETE
WARNING
Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a)
1. Install seat. After installing seat, pull up on seat to verify that it is secure. See service manual.
2. Install main fuse. See service manual.
3. Turn ignition on.
4. Test rear stop/tail/turn and hazard lighting functions.