FOOT PEG KIT
J065272021-08-02
GENERAL
Kit Number
50500803, 50500804, 50500805, 50500806, 50500807, 50500808, 50501008, 50501009, 50501010, 50501855, 50501856, 50501857, 50501898, 50501899, 50501900
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Kit Contents
See Figure 4 and Table 1.
Installation Requirements
E-CLIP TOOL (Part Number:HD-52369) to remove E-clips without damaging painted surfaces.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
INSTALLATION
1. See Figure 1. Vehicle is equipped with a pin (4) and retaining clip (2), remove them and retain for future use. Save all hardware, including torsion spring (1), for installation of new footpegs (3).
2. See Figure 1. Insert short leg of torsion spring (1) into hole in new footpeg (3).
NOTE
See Figure 2. When performing the next step, verify that the spring is positioned inside of the footpeg.
3. Align long leg of torsion spring (1) to hole in footpeg mount and insert.
4. Rotate footpeg (3) into position in clevis and insert pin (4) through clevis, footpeg (3) and spring (1).
5. Install retaining clip (2).
6. Repeat steps 2, 3, 4 and 5 on other side.
7. See Figure 3. For adjustable footpegs:
a. For forward controls, foot surface to be parallel to the mounting pin.
b. For mid controls, foot surface to be parallel to ground.
c. Tighten adjustment screw.
Torque: 29 N·m (21 ft-lbs) Adjusting screw
Wear Tip Replacement
1. See Figure 4. Remove existing wear tip from footpeg.
2. Apply 2 or 3 drops of threadlocker to threads of new wear tip and install to footpeg.LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
3. Tighten wear tip.
Torque: 19–22 N·m (14–16 ft-lbs) Wear tip
1Torsion spring
2Retaining clip
3Footpeg
4Pin
Figure 1. Rider Footpeg Torsion Spring Installation
Figure 2. Torsion Spring
Figure 3. Footpeg Adjusting Screw
Service Parts
Figure 4. Service Parts
Table 1. Service Parts Table
Item
Description (Quantity)
Part Number
1
Rubber footpeg (1)
Not sold separately
2
Socket head cap screw (1)
Not sold separately
3
Footpeg base (1)
Not sold separately
4
Footpeg wear peg (1)
50500901
5
Chrome medallion grip (2)
14100879
6
Footpeg mount (1)
Not sold separately
Figure 5. Service Parts: Kits 50501855, 50501856, 50501857, 50501898, 50501899, 50501900
Table 2. Service Parts: Kits 50501855, 50501856, 50501857, 50501898, 50501899, 50501900
Item
Description (Quantity)
Part Number
Kits 50501855, 50501856, 50501857
1
Footpeg, rider, left (chrome)
50501849
Footpeg, rider, left (black)
50501850
Footpeg, rider, left (black edge cut)
50501851
2
Footpeg, rider, right (chrome)
50501852
Footpeg, rider, right (black)
50501853
Footpeg, rider, right (black edge cut)
50501854
3
Wear peg
50500628
Kits 50501898, 50501899, 50501900
1
Footpeg, rider, left (chrome)
50501837
Footpeg, rider, left (black)
50501838
Footpeg, rider, left (black edge cut)
50501839
2
Footpeg, rider, right (chrome)
50501846
Footpeg, rider, right (black)
50501847
Footpeg, rider, right (black edge cut)
50501848
3
Wear peg
50500628