DETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT
J003252005-11-16
GENERAL
Kit Number
57965-97A, 58340-96, 58341-96, 58350-96, 58627-99, 58678-04, 57813-04
Models
These kits fit 1984 and later FXST, FXSTB, FXSTC, and 1993 and later FXDWG Harley-Davidson model motorcycles.
Table 1. Models
Kits | Contents |
|---|---|
57813-04 | Clear standard height windshield with flames |
57965-97A | Smoked Super Sport windshield |
58340-96 | Clear standard height windshield |
58341-96 | Smoked low profile windshield |
58350-96 | Docking hardware |
58627-99 | Smoked standard height windshield |
58678-04 | Clear "Skull with Wings" windshield |
NOTICE
Do not use windshield bags with flamed windshields. Damage to graphics will occur. (00393f)
NOTE
A Service Manual for your model motorcycle is available from your Harley-Davidson Dealer.
INSTALLATION
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
| 1. | Cover gas tank and front fender before beginning installation. | |
| 2. | For FXSTB models: Proceed to Step 6. For all other models except FXSTB: Relocate clutch cable to the inside of the handlebars as follows: a. Slide rubber boot off cable adjuster. Adjuster is located approximately halfway along clutch cable by the front frame downtube. b. Holding cable adjuster with 1/2 inch wrench, loosen jam nut using a 9/16 inch wrench. Back jam nut away from cable adjuster. Move adjuster toward jam nut to introduce a large amount of free play at the hand lever. c. Remove small snap ring from pivot pin groove at bottom of clutch lever bracket. Remove pivot pin and clutch hand lever from bracket. Remove anchor pin and clutch cable eyelet from clutch hand lever. d. See Figure 1. Reroute clutch cable to the inside of the handlebars and reconnect clutch cable to clutch lever. e. See Figure 2. Turn cable adjuster away from jam nut until slack is eliminated at hand lever. Pull clutch cable ferrule away from clutch lever bracket to check free play. Turn cable adjuster as necessary to obtain 1/16-1/8 inch (1.6-3.2 mm) free play between end of cable ferrule and clutch lever bracket. f. Hold adjuster with 1/2 inch wrench. Using 9/16 inch wrench, tighten jam nut against cable adjuster. Cover cable adjuster mechanism with rubber boot. |  Figure 1. New Clutch Cable Routing  Figure 2. 1/16-1/8 inch (1.6-3.2 mm) Clutch Cable Free Play |
| 3. | On all models except FXSTB: Remove turn signal lamp from right side of handlebar (brake side). Remove ball receptacle from turn signal assembly. Install lockwasher (12) and chrome acorn nut (11) from kit on end of mirror stalk to hold mirror in place. | |
| 4. | Remove turn signal lamp from left side of handlebar (clutch side). Remove ball receptacle mount from turn signal assembly. Replace acorn nut and lockwasher. | |
| 5. | Remove brake line clamp on upper fork triple clamp to allow right turn signal lamp to pass between brake line and right handlebar riser. All models except FXSTB skip to Step 7. | |
| 6. | On FXSTB models only: Remove existing turn signal clamps from fork tubes. Remove the original turn signal standoff from the turn signal. The original clamp and standoff will not be used during re-assembly. | |
| 7. | See Figure 5. Assemble mounting hardware for lower windshield mounting as shown in illustration. Assemble in the following order, and leave assembly loose: a. Locate the mounting hardware supplied in the docking hardware kit. Thread jam nut (9) from mounting kit onto the turn signal standoff end that is opposite the end with the flats (3). b. Thread standoff into turn signal assembly with jam nut facing turn signal. c. Place flat washer (5) and bushing (4) on standoff. d. Thread the clamp (8) onto the standoff. e. Install clamp assembly onto the fork tube with the clamp nut forward toward the headlamp. | |
NOTICE Do not exceed recommended torque when installing mounting screws. Damage to windshield can result. (00385a) | ||
| 8. | See Figure 5. Assemble hardware for upper windshield mounting as shown in illustration and tighten button head screws to 20 N·m (15 ft-lbs). The spacer (1), not visible in the illustration, fits between the retainer wire bracket (6, 7) and the upper fork triple clamp. NOTE Check for proper clearance between upper bushing and fuel tank before installing windshield as follows: See Figure 3. Turn the front forks to the left, allowing the fork to rest against the fork stop. Measure the clearance between the fuel tank and the upper bushing. We recommend using the shank end of the proper size drill bit as a feeler gauge between the fuel tank and the upper bushing. Before checking the clearance, place a piece of paper against the fuel tank to eliminate the possibility of scratching the fuel tank paint. Repeat this process with the front forks rotated fully to the right fork stop. If clearance is less than 5/32 inch (4 mm), contact your Harley-Davidson Dealer for additional information (reference P&A Service Bulletin P-40). |  Figure 3. 5/32 inch Minimum Clearance between Fuel Tank and Upper Bushing (looking down on docking point from above) |
| 9. | Hook the two top windshield assembly "jaws" into the grooves of the top bushings (4) then slide the lower clamp assemblies up until the lower bushings firmly fit into the lower windshield "jaws". | |
| 10. | With windshield in place, tighten lower clamp (8) hardware by first tightening clamp nut to 14 N·m (10 ft-lbs). Be sure the clamp does not rotate during tightening (the mounting bushing must be parallel to the windshield brackets). | |
| 11. | With clamps secured to forks, tighten standoff into mounting clamp to 20 N·m (15 ft-lbs). Then, align turn signals and tighten jam nuts (9) to 14 N·m (10 ft-lbs). |  Figure 4. Cable Ties and Turn Signal Wire Routing |
| 12. | See Figure 4. Remove windshield by grabbing windshield edges parallel with center brace and firmly pulling windshield loose from upper bushing grooves. Lift windshield assembly off of lower bushings. With windshield removed, and using cable straps in kit, securely route turn signal wires. After wires are secured, check turn signal wire clearance with the windshield installed. | |
| 13. | Reattach brake line clamp to upper fork triple clamp. |
WARNINGImproper installation of accessories or loading of cargo can affect motorcycle stability and handling, which could result in death or serious injury. (00455b)
WARNINGFailure to provide adequate clearance between stationary and moving parts can cause loss of control, which could result in death or serious injury. (00378a)
NOTE
Inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. Restricted movement could affect handling, resulting in death or serious injury. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed.
NOTE
Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of components.
CARE AND CLEANING
NOTE
Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections.
NOTICE
Polycarbonate windshields/wind deflectors require proper attention and care to maintain. Failure to maintain polycarbonate properly can result in damage to the windshield/wind deflector. (00483e)
NOTICE
Use only Harley-Davidson recommended products on Harley-Davidson windshields. Do not use harsh chemicals or rain sheeting products, which can cause windshield surface damage, such as dulling or hazing. (00231c)
NOTICE
Use only Harley-Davidson recommended products on Harley-Davidson windshields. Do not use harsh chemicals or rain sheeting products, which can cause windshield surface damage, such as dulling or hazing. (00231c)
Do not clean Lexan® polycarbonate in hot sun or high temperature. Powdered, abrasive or alkaline cleanser will damage the windshield. Never scrape the windshield with a razor blade or other sharp instruments because permanent damage will result.
NOTE
Covering the windshield with a clean, wet cloth for about 15 minutes before washing will make dried bug removal easier.
Harley-Davidson Windshield Water Repellent Treatment part number 99841-01 is approved for use on Harley-Davidson Lexan® windshields.
SERVICE PARTS
Figure 5. Service Parts: Docking Hardware
Table 2. Service Parts: Docking Hardware
Item | Description (Quantity) | Part Number | Item | Description (Quantity) | Part Number | |
|---|---|---|---|---|---|---|
1 | Spacer (2) | 58349-96 | 7 | Right retainer wire bracket | 58515-96 | |
2 | 5/16-24 x 7/8 button head screws (2) | 94467-94T | 8 | Mounting clamps (2) | 58351-96 | |
3 | Turn signal standoffs (2) | 58556-97 | 9 | 5/16-24 chrome nuts (2) | 94043-90T | |
4 | Bushings (4) | 67621-94 | 10 | Cable ties (6) (not shown) | 10006 | |
5 | 5/16 chrome flat washers (4) | 94066-90T | 11 | 5/16-24 chrome acorn nut (used on right side mirror) (not shown) | 7736 | |
6 | Left retainer wire bracket | 58514-96 | 12 | 5/16 internal tooth lockwasher (used on right side mirror) (not shown) | 7127 |
Figure 6. Service Parts: Windshield
Table 3. Service Parts: Windshield
Item | Description (Quantity) | Part Number | Item | Description (Quantity) | Part Number | |
|---|---|---|---|---|---|---|
1 | Windshield | 10 | LH windshield retainer | 58329-96 | ||
For Kit 57813-04, standard height with flames | 57815-04 | 11 | RH windshield retainer | 58328-96 | ||
For Kit 58340-96, standard height, clear | 58288-95 | 12 | Nylon bushings (4) | 58272-95 | ||
For Kit 58341-96, low profile, smoked | 58271-95 | 13 | RH brace | 58406-75A | ||
For Kit 58627-99, standard height, smoked | 58629-99 | 14 | LH brace | 58408-75A | ||
For Kit 58678-04, standard height, clear | 58288-95 | 15 | Windshield brace tape (2) | 58417-77 | ||
2 | Pan head screws, Torx (2) | 2452 | 16 | Button head screws (2) | 94426-95 | |
3 | Pan head screws, Torx (7) | 2921 | 17 | Acorn nuts (9) | 7651 | |
4 | Inner windshield brace | 58050-78A | 18 | Acorn nuts, 1/4-20 (3) | 94004-90T | |
5 | Outer windshield brace | 58051-78A | 19 | Flat washers, 1/4 inch (2) | 6703 | |
6 | Windshield brace tape (2) | 58052-78 | For Kit 58678-04 only | |||
7 | LH windshield bracket | 58344-96 | 20 | Inner windshield brace | 58551-04 | |
8 | RH windshield bracket | 58345-96A | 21 | Outer windshield brace | 58550-04 | |
9 | Washers (6) | 58152-96 | 22 | Windshield brace tape (2) | 58540-04 | |
Figure 7. Service Parts: Windshield Kits
Table 4. Service Parts: Windshield Kits
Item | Description (Quantity) | Part Number | Item | Description (Quantity) | Part Number | |
|---|---|---|---|---|---|---|
1 | Windshield | 57731-98 | 8 | LH windshield retainer | 58329-96 | |
2 | Button head screws (4) | 94639-99 | 9 | RH windshield retainer | 58328-96 | |
3 | Washers (4) | 6352 | 10 | Nylon bushings (4) | 58272-95 | |
4 | Washers, rubber (8) | 58152-96 | 11 | Acorn nuts, 1/4-20 (2) | 94004-90T | |
5 | Acorn nuts (4) | 94007-90T | 12 | Flat washers, 1/4 inch (2) | 6703 | |
6 | LH windshield bracket | 57967-97A | 13 | Button head screws (2) | 94426-95 | |
7 | RH windshield bracket | 57968-97A | ||||