SCREAMIN' EAGLE PERFORMANCE IGNITION MODULE

J035152006-11-30

GENERAL

Kit Number

Table 1. Kits

Kits	RPM LIMIT
32471-06	7000
31758-04A	7000
31759-04A	7000
31787-04A	6200
31792-04A	6200

Models

For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).

WARNING

Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)

NOTE

This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer.

Kit Contents

This kit contains a performance ignition module.

There are no Service Parts available with this kit.

NOTE

Do not install these ignition components on any model other than those specified. Doing so may result in adverse engine operation and/or damage to vehicle electrical and engine components.

NOTE

This Screamin' Eagle ignition system is intended for high performance applications only. This engine related performance part is not legal for use on pollution controlled motor vehicles. Use of this Screamin' Eagle ignition system may reduce or void the Limited Warranty coverage.

NOTE

This Screamin' Eagle ignition system allows the engine to reach higher than original equipment rev. limit. It is extremely important that the rider use the tachometer and avoid harmful over-revving and possible engine damage. Engine-Related Performance Parts are intended for the experienced rider only.

This kit is designed for use on engines with stock compression, but equipped with other minor modifications such as high-performance cams, intake and exhaust systems.

NOTE

Faulty ignition module operation may result from wiring harness problems. If this Screamin' Eagle ignition system malfunctions, inspect the motorcycle's wiring harness to determine if it is faulty. If the existing wiring harness is faulty, repair or replace it before installing the new ignition module.

INSTALLATION

WARNING

To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a)

1.	Disconnect the battery negative cable.
2.	Refer the Service Manual to remove the seat.
3.	Refer to the Service Manual to locate and access the existing ignition module.
4.	Unplug the ignition module. Remove module and save mounting fasteners.
5.	Plug in new module and secure module in place with original mounting fasteners.
6.	Reconnect battery negative cable.
	WARNING After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b)
7.	Install the seat.
8.	See Table 2. Perform "Setting TSM/TSSM and ECM/ICM Password" procedure.

Table 2. Setting TSM/TSSM and ECM/ICM Password

NO.	ACTION	CONFIRMATION	NOTES
	Ignition must be turned off for at least 15 seconds.	With ignition turned off, Check Engine Lamp and Security Lamp will be off.
1	Install new TSM/TSSM or ECM/ICM. Perform all steps under 3.3 TSM/TSSM VEHICLE DELIVERY/SETUP.
2	SET RUN/OFF SWITCH TO RUN.
3	Turn IGN key ON.	Verify Check Engine Lamp and Security Lamp illuminate and then turn off.	TSM/TSSM enables starter relay.
4	Attempt normal start one time.	Carbureted models: Engine starts and stalls. Check Engine Lamp performs 4 seconds on, 4 seconds off, 8 seconds on, off sequence. EFI models: Engine starts and stalls. Check Engine Lamp illuminates and stays on.	Password has not been learned. ECM/ICM sets DTC P1009.
5	Wait ten seconds. Security lamp will illuminate and stay on.	Security Lamp illuminates.	ECM/ICM enters Password Learning mode for ten minutes. Do not cycle ignition switch or interrupt vehicle power or Password Learn will be unsuccessful
6	Wait until Security lamp turns off.		This takes ten minutes.
7	Quickly (within two seconds) turn IGN key OFF-ON.		ECM/ICM must not be allowed to shutdown.
8	Wait until Security Lamp turns off.		This takes ten minutes.
9	Quickly (within two seconds) turn IGN key OFF-ON		ECM/ICM must not be allowed to shutdown.
10	Wait until Security Lamp turns off.		This takes ten minutes.
11	Quickly (within two seconds) turn IGN key OFF-ON.		ECM/ICM must not be allowed to shutdown.
12	Turn IGN key OFF. Wait 15 seconds before turning IGN on. Turn IGN switch ON and start engine to confirm sucessful Password Learn procedure. Clear trouble codes.
13	Perform all steps under 3.3 TSM/TSSM VEHICLE DELIVERY/SETUP.