ULYSSES TALL WINDSCREEN
J037902010-04-28
GENERAL
Kit Number
58214-06YB
Models
For model fitment information, see www.buell.com (English only).
REMOVAL
NOTE
The windscreen releases from the flyscreen by pulling it outward and away from the vehicle.
| 1 | Windscreen |
| 2 | Flyscreen |
| 3 | Mounting pin, upper (2) |
| 4 | Mounting pin, lower (2) |
Figure 1. Windscreen Removal
See Figure 1. Remove the stock windscreen (1) by pulling it loose from the flyscreen (2). Pull sharply at the upper (3) and lower (4) mounting pins to release it from the flyscreen.
INSTALLATION
NOTE
See Figure 2. The windscreen (1) upper mounting locations use mounting pins (2) (Factory installed in windscreen) and the lower two mounting locations use fasteners. It will be necessary to remove the flyscreen in order to properly install the new windscreen.
- Remove the six screws (C) from the flyscreen and flyscreen from motorcycle. Place flyscreen face down on a clean soft surface to prevent scratching or damage.
- See Figure 2. Install the new windscreen (1) by pushing the upper mounting pins (2) into place. Verify upper mounting pins on windscreen locate properly into upper mounting grommets (B) of flyscreen (A).
- Aligned the lower flyscreen and windscreen holes. For the left and right side lower holes, insert finish washer (5) and spacer (6) onto the screw (4) and place through the windscreen, grommet, and flyscreen holes.
- From the inside of the flyscreen, place washer (7) onto screw (4) and thread lock nut (8) onto screw. Tighten screw to 25-30 in-lbs (2.8-3.4 Nm).
- Install flyscreen (A) (with windscreen attached) using 6 screws removed earlier. Tighten screws to 10-12 in-lbs (1.1-1.4 Nm).
NOTE
The windscreen MUST be installed to the flyscreen while both components are off the motorcycle. The lower fasteners can not be installed if flyscreen is left installed on the motorcycle.
CARE AND MAINTENANCE
NOTICE
Polycarbonate windshields/wind deflectors require proper attention and care to maintain. Failure to maintain polycarbonate properly can result in damage to the windshield/wind deflector. (00483e)
- Do not use benzene, paint thinner, gasoline or any other type of harsh cleaner on the windscreen/windshield. Doing so will damage the surface.
- Do not clean Lexan in hot sun or high temperature.
- Powdered, abrasive or alkaline cleanser will damage the windscreen/windshield.
- Sunlight reflections off of the inside curvature of a windscreen/windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windscreen/windshield to avoid reflections.
- Do not use benzene, paint thinner, gasoline or any other cleaning agents on the rubber bushings. Doing so will damage the bushing surfaces.
NOTE
Covering the windshield with a clean, wet cloth for about 15 minutes before washing will make dried bug removal easier.
SERVICE PARTS
Figure 2. Service Parts: Ulysses Tall Windscreen
Table 1. Service Parts Table
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Windscreen | Not sold separately |
2 | Windscreen mount pin, upper (2) | M0230.1AKB |
3 | Windscreen mounting hardware kit, lower | Not sold separately |
Lower Hardware Kit Components: | ||
4 | Screw, 10-24 (2) | 4656Y |
5 | Finish washer (2) | 6484Y |
6 | Spacer, stainless steel (2) | 6491Y |
7 | Washer, #10 (2) | 6716 |
8 | Lock nut, 10-24 (2) | 7624 |
Items mentioned in text, but not included in kit: | ||
A | Flyscreen | |
B | Mounting grommet | |
C | Flyscreen mounting screws (6) | |