CUSTOM POLISHED ALUMINUM REAR WHEEL
J022772006-04-11
GENERAL
Kit Numbers
41313-04, 43760-03, and 43760-03A.
Models
Kit 41313-04 fits 2003 and later Softail models except FLSTS, FLSTSC, and FXSTD.
Kit 43760-03 fits all 2002, and later touring model motorcycles. 2007 Touring models require the use of 3737A (5) screws, and 6516HW (5) washers.
Kit 43760-03A fits all 2002, and later touring model motorcycles.
Additional Parts Required
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer.
INSTALLATION
Refer to the appropriate Service Manual for wheel removal, and installation procedures.
See the Service Parts illustration. This kit contains parts for the wheel installation. However, the following original equipment parts are re-used for wheel installation.
- Axle
- Axle nut
- Cotter pin or spring clip for axle nut
- Brake disc
- Hub caps
- Wheel spacers
- Sprocket
NOTE
Follow the sprocket bolt tightening procedure in our service manual, or if installing an accessory hardware kit in the I-Sheet included with the hardware kit.
NOTICE
Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c)
NOTICE
Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b)
WARNINGWhenever a wheel is installed and before moving the motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00284a)
WHEEL CARE
WARNINGBe careful not to get the brakes wet when washing vehicle. Wet brake pads and/or discs can adversely affect brake performance, which could result in death or serious injury. (00079b)
NOTE
To guard against pitting, and corrosion the wheels must be cleaned, and maintained according to to these wheel care instructions. Corrosion of these materials is not considered to be a defect in materials or workmanship.
The vehicle's wheel are aluminum, and do not have a protective coating. Damage from harsh chemicals, acid based wheel cleaners, brake dust, and lack of maintenance can occur. Regular washing, and the use of a corrosion protectant helps maintain the wheel's original appearance. Harley-Davidson recommends Harley-Davidson® Wheel and Tire Cleaner part 94658-98 for cleaning wheels and tires; and Harley-Davidson® Harley Glaze® part 99701-84 followed by Harley Gloss® part 94627-98 to protect the aluminum wheel surfaces.
SERVICE PARTS
Figure 1. Service Parts: Custom Polished Aluminum Rear Wheel
Table 1. Service Parts Table
Kit: 43760-03 and 43760-03A | Kit: 41313-04 | |||||
|---|---|---|---|---|---|---|
Item | Description (Quantity) | Part Number | Item | Description (Quantity) | Part Number | |
1 | Screw | 43567-92 | 1 | Screw | 43567-92 | |
2 | Wheel bearing (2) | 9247 | 2 | Wheel bearing (2) | 9267 | |
3 | Bearing spacer | 43517-00 | 3 | Bearing spacer | 43608-00 | |
4 | Wheel | Not sold separately | 4 | Wheel | Not Sold Separately | |
5 | Valve stem assembly | 43157-83A | 5 | Valve stem assembly | 43157-83A | |
NOTE
Items A and B must be purchased separately. See your dealer for the correct part numbers for your year, and model motorcycle. If installing kit 43760-03 on a 2007 Touring model you must use (5) screws 3737A, and (5) washers 6516HW.