SPORTSTER LEATHER SADDLEBAG KIT
J038452009-06-23
GENERAL
Kit Number
53050-04C
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Additional Parts Required
This kit requires the separate purchase of a Turn Signal Relocation Kit 60215-06 or 68732-02A for domestic and 68733-02A for international.
WARNINGDo not exceed saddlebag weight capacity. Put equal weight in each bag. Too much weight in saddlebags can cause loss of control, which could result in death or serious injury. (00383a)
NOTE
Maximum saddlebag weight is 7 pounds (3.2 Kg) for each bag.
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer.
INSTALLATION
WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a)
| 1. | Refer to the service manual and follow the instructions given to remove the seat, and disconnect the negative battery cable. Save seat mounting hardware for later use. | |||||||||
| 2. | Properly support motorcycle under frame with stand or suitable blocking to prepare for addition of saddlebags. | |||||||||
| 3. | See Figure 1. Remove and discard front and rear button head screws (1), two locknuts (2) and under fender clip nuts (3) from the left and right rear fender support covers (4). NOTE Rear turn signals must be relocated to new turn-signal bar on the rear license plate bracket. | |||||||||
| 4. | Follow the instructions provided with the Turn Signal Relocation Kit to relocate the rear turn signals. | 
Figure 1. Rear Fender Support Removal | ||||||||
| 5. | See Figure 2. From the underside of the fender, install two bolts (6) from kit through the fender and into the fender support (A) and cover (B), where the two button head screws were previously removed in Step 3. | |||||||||
| 6. | Install the short bushing (12) onto the front bolt (short end toward saddlebag and the long bushing (11) onto the rear bolt (short end toward saddlebag). | |||||||||
| 7. | Slide the saddlebag onto the bolts until bushings are seated onto the saddlebag bracket. | |||||||||
| 8. | Thread flange locknuts (7) to bolts on the inside of the saddlebag. Tighten both flange locknuts to 24-27 ft-lbs (33-37 Nm). | |||||||||
| 9. | Install a thread protector cap (8) onto each of the bolt ends. |
Install Reflectors
WARNINGFederal Motor Vehicle Safety Standard (FMVSS) 108 requires motorcycles to be equipped with rear and side reflectors. Be sure rear and side reflectors are properly mounted. Poor visibility of rider to other motorists can result in death or serious injury. (00336b)
- Measure approximately 1-1/2 in (38 mm) from the bottom edge of the saddlebag. Orient the reflector horizontally and carefully center the reflector mount between the straps of bags with straps or locate it at the rearward portion of bags without straps.
- See Figure 2. Position reflector mount (14) on saddlebag.
- Mark holes on saddlebag with pen (or other appropriate tool).
- Using soapy water, clean the surface where reflector will be installed.
- Allow the surface to dry completely before continuing.
- Using appropriate tool, make two 3/16 inch holes in saddlebag.
- Install reflector mount (14) on saddlebag using two push nuts (15).
- Remove backing from adhesive on reflector (16) and install on mount (14).
- Let the adhesive cure for at least 24 hours at no less than 60°F (16°C).
SERVICE PARTS
Figure 2. Service Parts: Sportster Rigid Leather Saddlebag Kit (right side shown)
Table 1. Service Parts: Sportster Rigid Leather Saddlebag Kit
Item | Description (Quantity) | Part Number | Item | Description (Quantity) | Part Number | |
|---|---|---|---|---|---|---|
1 | Saddlebag without lock, right | 53099-04A | 9 | Plug, 0.40 in. hole (2) | 53377-04 | |
2 | Saddlebag without lock, left (not shown) | 53113-04A | 10 | Plug, 0.35 in. hole (2) | 68446-00 | |
3 | Lock assembly (2) (includes keys) | 51557-00A | 11 | Bushing, rear, long | 53021-04 | |
4 | Bezel, right | 53126-04A | 12 | Bushing, front, short | 53022-04 | |
5 | Bezel, left (not shown) | 53131-04A | 13 | Kit, reflector (items 14-16) | 59480-04A | |
6 | Screw, Hex head, 5/16-18 x 3 in. (4) | 4375 | 14 | Mount, reflector | Not sold separately | |
7 | Locknut, flange 5/16-18 (4) | 7531 | 15 | Pushnut, reflector mount (2) | 8126A | |
8 | Cap, thread protector (4) | Not sold separately | 16 | Reflector, red | 59270-10 | |
A | Frame fender support | Not part of kit | 17 | Ornament kit | 53124-04 | |
B | Frame fender support cover | Not part of kit |