LED TAIL LAMP WITH BAR & SHIELD LOGO
J037182007-11-02
GENERAL
Kit Numbers
68085-08 (Red lens/Chrome), 68087-08 (Smoke lens/Black), 68086-08 (Smoke lens/Chrome), 68116-08 (Red lens/Chrome), 68117-08 (Smoke lens/Chrome), 68118-08 (Smoke lens/Black)
Models
For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Additional Parts Required
NOTE
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation, and is available from a Harley-Davidson Dealer.
INSTALLATION
For models WITH main fuse:
WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
- Refer to the Owner's Manual and follow the instructions to remove the seat and main fuse. Retain all seat mounting hardware.
For models WITHOUT main fuse:
WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a)
NOTE
For 2004 and later XL (Sportster®) models, the negative battery cable is most easily disconnected at the engine crankcase.
| 1. | Refer to the Owner's Manual and follow the instructions to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. NOTE Figure 1 shows the original equipment tail/stop lamp mounted to a full fender. The lamp is rotated 180° when mounted to a Bobtail fender. | |||||||||||||||||||||||
| 2. | See Figure 1. Loosen the two screws (2) retaining the tail/stop lamp assembly (1) to the lamp base (3), and pull the lamp assembly away from the base. | |||||||||||||||||||||||
| 3. | Push the locking tab (button), and disconnect the tail/stop lamp connector [93B] (4) from the circuit board. Remove the lamp from the vehicle. | 
Figure 1. Removing the Tail/Stop Lamp Assembly 
Figure 2. Socket Terminal Installation | ||||||||||||||||||||||
| 4. | On the new tail/stop lamp assembly, the Blue wire and socket terminal are not installed in the four-way socket housing. Refer to the original lamp removed in Step 3, and observe which cavity contains the Blue wire. Note that the cavities are numbered on the face of the secondary lock. The Blue wire and terminal must be installed into the same cavity in the socket housing of the new lamp as follows: a. See Figure 2. On the secondary lock (2) side of the socket housing (1), position the socket terminal (5) with the slot (6) and crimp tails (7) facing up (in the same direction as the button (3) on the top of the socket housing). b. Insert the terminal into the correct cavity (4) until it snaps into place with an audible "click". c. Gently tug on the wire end to verify that the terminal is locked in place and will not back out of the cavity. d. Rotate hinged secondary lock inward until tabs fully engage the latches on both sides of the connector. NOTE If the terminal must be removed and re-installed, refer to the MULTILOCK ELECTRICAL CONNECTORS section of the appropriate Service Manual. Fill pin cavities in the circuit board with dielectric grease from the packet in the kit before assembling connector halves. | |||||||||||||||||||||||
| 5. | Connect the socket housing on the new tail/stop lamp assembly to the four-way pin housing in the circuit board. NOTE Do not over-tighten the screws. Over-tightening the screws can crack the tail/stop lamp lens or result in scratching of the fender paint. | |||||||||||||||||||||||
| 6. | Install the tail/stop lamp to the vehicle, and alternately tighten the screws to 2.3–2.7 N·m (20–24 in-lbs). NOTE See Figure 1. Lamp assembly (1) attaches as shown on full fender models. On Bobtail models, lamp assembly is rotated 180°. The logo (2) is not factory installed so logo can be installed in the upright position. | |||||||||||||||||||||||
| 7. | See Figure 3. Peel the liner from the adhesive backing of the Bar & Shield emblem (2) from the kit. Orient the emblem with the logo upright, and carefully position the emblem to the recessed area in the center of the tail/stop lamp lens. Press firmly into place, ensuring that the edge is securely fastened all around. NOTE Allow AT LEAST 24 hours after applying the emblem before exposing the area to vigorous washing, strong water spray or extreme weather. | |||||||||||||||||||||||
NOTICE Do not over-tighten bolts on battery terminals. Use recommended torque values. Over-tightening battery terminal bolts could result in damage to battery terminals. (00216a) | ||||||||||||||||||||||||
| 8. | Verify that the ignition/ light key switch is in the OFF position. Models WITH main fuse: Refer to the Owner's Manual and follow the instructions to install the main fuse. Models WITHOUT main fuse: Connect the negative (-) battery cable per the instructions in the Owner's Manual. Apply a light coat of petroleum jelly or corrosion retardant material to the negative battery terminal. Refer to the Owner's Manual, and follow the instructions to install the seat. | |||||||||||||||||||||||
| WARNING After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) WARNINGBe sure headlamp, tail and stop lamp and turn signals are operating properly before riding. Poor visibility of rider to other motorists can result in death or serious injury. (00478b) | ||||||||||||||||||||||||
| 9. | Turn the ignition/ light key switch to ON, but do not start motorcycle. Test for proper tail and stop lamp operation. |
SERVICE PARTS
Figure 3. Service Parts: LED Tail Lamp with Bar & Shield Logo (Non-FLHX Model Shown)
Table 1. Service Parts Table
Item | Description | Part Number |
|---|---|---|
1 | Assembly, tail lamp, red lens, chrome | Not sold separately |
Assembly, tail lamp, smoke lens, chrome | Not sold separately | |
Assembly, tail lamp, smoke lens, black | Not sold separately | |
2 | Emblem, Bar & Shield | Not sold separately |
3 | Die electric grease | Not sold separately |
4 | Screw, chrome | 68026-99 |
5 | Socket terminal | 73191-96 |
6 | Housing, socket, 4-way | 73154-96BK |