H-D DETACHABLES DYNA UPRIGHT KIT
J047322014-06-30
GENERAL
Kit Number
51161-10A, 52300042A, 52300044A, 52300046A
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
Separate purchase of extra parts or accessories may be required for proper installation of this H-D® Detachables Kit. See the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only) for a list of required parts or accessories.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
WARNING
After installing sissy bar/sideplate assembly, pull upward to be sure it is locked in position. While riding, a loose sissy bar/sideplate assembly can shift causing loss of control, which could result in death or serious injury. (00388a)
WARNING
Federal Motor Vehicle Safety Standard (FMVSS) 108 requires motorcycles to be equipped with rear and side reflectors. Be sure rear and side reflectors are properly mounted. Poor visibility of rider to other motorists can result in death or serious injury. (00336b)
Kit Contents
See Figure 3 and Table 1.
INSTALLATION
Install Docking Point Kit
Install the docking point kit following the instructions in that kit.
Passenger Upright Installation
1. See Figure 1. Stand behind the motorcycle, and place (10) the front upright notches (2) into the front docking points (3).
2. See Figure 2. Check for correct notch engagement.
NOTE
Failure to engage the sideplate notches to the docking points can damage to the docking points.
3. See Figure 1. Pull (11) the rotary latches (4) into a rearward position. Align the latches over the rear docking points (7). Make sure the latches and rear notches (6) fit into the neck (8) of the rear docking points.
NOTE
This may require some gentle squeezing or spreading of the upright sideplates.
4. Push downward (12) on the side plates. Close the rotary latches by rotating the latch levers as far forward as they will go (13). A click is heard when the latch is in place. If the latch does not close, do not force it.
1Upright
2Front notch
3Front docking point
4Rotary latch
5Release button
6Rear notch
7Rear docking point
8Rear docking point neck
9Fender support bracket
10Place front notches into front docking points
11Pull latches rearward
12Lower rear notches onto rear docking points
13Push forward to close latches
Figure 1. Detachable Upright
1Correct
2Incorrect
3Incorrect
Figure 2. Upright Notch to Docking Point Engagement
5. See Figure 2. Check for correct notch engagement.
6. If rear side reflectors for this model motorcycle were included in the Docking Hardware Kit or Saddlebag Kit, remove the original equipment reflectors. Install the reflectors supplied with that kit.
REMOVAL
To remove the upright, press the release buttons. Pull the rotary latches rearward. Carefully lift the rear of the sideplates up. Pull the upright out of the front docking points.
SERVICE PARTS
Figure 3. Service Parts: H-D Detachables Upright
Table 1. Service Parts
Item
Description (Quantity)
Part Number
1
Detachable upright
Not Sold Separately
2
Stud, pivot (2)
Not Sold Separately
3
Logo, Bar & Shield
13883-00
4
Latch assembly (2) (includes items 5-10)
50300108
5
Washer
6827
6
Screw
Not Sold Separately
7
Washer, wave (2)
6828
8
Compression spring (not shown)
53602-95