SCREAMIN' EAGLE TWIN CAM 4.625" STROKE FLYWHEEL KITS
J054712011-05-12
GENERAL
Kit Numbers
24100004A, 23893-10A
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Kit Contents
Table 1. Kit Contents
Description (Quantity) | Part Number |
|---|---|
Flywheel assembly (1) | Not Sold Separately |
Additional Parts Required
NOTE
SE Lefty Bearing Kit (Part Number 24004-03B) must be used on the primary side of flywheel. Follow instructions included with bearing assembly.
If an SE crankcase is used, the lefty main bearing is already installed. However, an additional thrust washer (Part Number 8972) will be required.
For 2006-2011 Dyna, 2007-2010 Touring, and 2007-2011 Softail Models (except FXCW and FXCWC Models): Installation of SE High Capacity Compensator Kit (40274-08A) is required for installation of this kit.
For 2012-later Dyna, Softail and all FXCW and FXCWX Models, 2011-later Touring Models: Separate purchase of an SE High Capacity Compensator Kit is not required.
Table 2. Additional Parts Required
Description | Part Number |
|---|---|
4.060" Bore Cylinders | See Catalog |
4.060"/4.625" Bore/Stroke Pistons | See Catalog |
Engine overhaul gasket kit | See your Dealer |
SE Lower Piston Cooling Jet | See Catalog |
Big Twin Compensator Kit (See Note, above) | 40274-08A |
SE Lefty Bearing Kit (See Note, above) | 24004-03B |
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
- This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer.
- Harley-Davidson motorcycles equipped with some Screamin' Eagle® high-performance parts may not be used on public roads and in some cases must be restricted to closed course competition. This engine related performance part is intended for racing applications and is not legal for sale or use in California on pollution controlled motor vehicles.
WARNINGWhen servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a)
INSTALLATION
WARNINGDisconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a)
- Disconnect the battery, negative cable first.
- Follow instructions in applicable service manual and remove engine from chassis.
- Refer to the ENGINE section in the service manual and follow steps to disassemble engine and remove crankshaft.
- For stock crankcases: Refer to the service manual for removal and installation of the main bearing in the left crankcase half from the SE Lefty Bearing Kit. For SE crankcases: See Figure 1. Use thrust washer (2) (Part Number 8972) purchased separately when installing flywheel in crankcase.
- For 2006-2011, 2007-2010 Touring, and 2007-2011 Softail Models (except FXCW and FXCWC Models): Install SE High Capacity Compensator Kit (40274-08A, purchased separately). Follow instructions included with the kit. For 2012-later Dyna, Softail and all FXCW and FXCWX Models, 2011-later Touring Models: Install original equipment compensator following instructions in the service manual.
- Refer to ENGINE section in the service manual and follow steps for assembling engine with the new crankshaft.
- Follow instructions in applicable service manual and install engine in chassis.
NOTE
See Figure 1. The inner bearing race and one thrust washer will be discarded from the SE Lefty Bearing since the new flywheel comes with a race and thrust washer installed.
Operation
- Refer to BREAK-IN RIDING RULES in the owner's manual for instructions to break-in a new engine.
| 1 | Flywheel assembly (includes items 2 and 3) |
| 2 | Thrust washer |
| 3 | Bearing inner race (remove and replace) |
| 4 | Thrust washer (from Lefty Bearing Kit) |
| 5 | Bearing inner race (from Lefty Bearing Kit) |
| 6 | Lock Ring (from Lefty Bearing Kit) |
| 7 | Straight roller bearing (from Lefty Bearing Kit) |
| 8 | Crankcase (left side shown) (save existing parts) |
| 9 | Seal (purchased separately) |
| 10 | Spacer (save existing part) |
Figure 1. Bearing and Thrust Washer Installation