CHROME AUXILIARY LAMP KIT
J051172010-07-25
GENERAL
Kit Number
69285-05A
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Additional Parts Required
Auxiliary / fog lamps are not included in this kit. The desired style of lamp must be purchased separately. HDI (International) motorcycles should only use approved fog lamps.
Models with turn signals mounted on the upper or lower triple clamp will also require Front Directional Relocation Kit (Part No. 68603-01), available separately at any Harley- Davidson Dealer.
Separate purchase and installation of additional parts or accessories may be required for proper installation of this kit on your model motorcycle. See the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only) for a list of required parts or accessories for your model.
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
Kit Contents
NOTICE
It is possible to overload the vehicle's charging system by adding too many electrical accessories. If the combined electrical accessories operating at any one time consume more electrical current than the vehicle's charging system can produce, the electrical consumption can discharge the battery and cause damage to the vehicle's electrical system. (00211d)
These lamps require 2.9 amps of available current from the motorcycle's electrical system.
INSTALLATION
For ALL vehicles with main fuse:
WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
NOTE
For vehicles equipped with security siren:
- Verify that the Hands-Free Fob is present.
- Turn the ignition key switch to IGNITION.
- Refer to the service manual and follow the instructions to remove the main fuse.
For ALL vehicles with main circuit breaker:
WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a)
| 1. | Refer to the service manual and follow the instructions to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. | |||||||||||||||||||||||
| WARNING Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a) | ||||||||||||||||||||||||
| 2. | Remove the fuel tank following the instructions in the service manual. | 
Figure 1. Install Mounting Bracket on Fork Tube (Right Side Shown) 
Figure 2. Install Lamps (Right Side Shown) | ||||||||||||||||||||||
| 3. | See Figure 1. The mounting brackets (1) and clamps (2) are side-specific. Select the right-hand or left-hand bracket and clamp, and install on the fork tube with two button-head screws (3 and 4) from the kit. | |||||||||||||||||||||||
| 4. | Starting with the outer screw first (3), tighten to 8–9 N·m (70–80 in-lbs). Repeat for screw (4). | |||||||||||||||||||||||
| 5. | See Figure 2. Route the lamp wire (1) through the hole in the mounting bracket (2), and secure the lamp (3) to the bracket using a clamp block (4), lockwasher (5) and retainer (6) from the kit. Tighten the retainer to 16-18 ft-lbs (22-24 Nm). | 
Figure 3. Auxiliary Lamp Bulb Terminals 
Figure 4. Wiring Harness Component Identification | ||||||||||||||||||||||
| 6. | See Figure 10. Locate the outer trim ring (24), inner nesting ring (27), screw (25), and nut (26). | |||||||||||||||||||||||
| 7. | See Figure 3. Place the inner nesting ring on the bulb. Connect the black wire to the bulb spade terminal next to the bulb indexing tab (1) on the bulb. Install the gray wire on the remaining spade terminal. | |||||||||||||||||||||||
| 8. | Attach the bulb and nesting ring using the trim ring, screw and nut identified in Step 6. | |||||||||||||||||||||||
| 9. | See Figure 2. Slide the conduit (7) from the kit over the lamp wire. | |||||||||||||||||||||||
| 10. | Repeat Steps 3 through 9 for the opposite side. NOTE See Figure 4 for wiring harness component identification. | |||||||||||||||||||||||
NOTICE When routing wires and harnesses, verify that they are clear of moving parts, heat sources and pinch points to avoid wire damage or a short circuit, which could result in electrical system damage. (00579b) | ||||||||||||||||||||||||
| 11. | See Figure 5. Install the wiring harness. Place the relay (1) in the opening in the seat pan, and route the long leg of the harness (3) along the frame backbone. | |||||||||||||||||||||||
| 12. | 2011 and later Softail models: Connect the 6-place Deutsch connector to the 6-place diagnostics/P&A connector on the vehicle harness. All 2003 and earlier models: Cut the 6-place connector from the harness. Install a ring terminal from the kit to the white power lead and connect it to the copper stud (BAT) terminal of the main circuit breaker. All 2004 and later models except 2011 and later Softail models: Cut the 6-place connector from the harness. Splice the B+ jumper harness (item 28, Figure 10 ) to the white power lead and connect the jumper to the B+ connector on the harness. See the SEALED SPLICE CONNECTORS section of the service manual. | |||||||||||||||||||||||
| 13. | All models except 2011 and later Softail models:Install a ring terminal from the kit to the black ground lead of the harness. Connect the black ground wire (2) with the ring terminal to the ground stud under the seat, or at any good electrical ground point. Secure the kit harness to the adjacent harnesses with cable straps (Item 16, Figure 10 ). | |||||||||||||||||||||||
| 14. | See Figure 4. Route the harness past the steering head, and route the lamp switch (3) leg of the harness along the left side of the handlebar to the clutch control. | |||||||||||||||||||||||
| 15. | See Figure 10. Obtain the switch mounting bracket (Item 19) from the kit. Remove the boot from the lamp switch, and install the switch into the bracket. Replace the boot on the switch. NOTE If the boot becomes worn or damaged, or is lost, replace the boot to prevent moisture from entering the switch. See Figure 10 (item 11). | |||||||||||||||||||||||
| 16. | See Figure 6. Remove the lower screw (1) and washer from the clutch control clamp, and install the lamp switch and bracket assembly (2). Install the screw and washer and tighten to 7–9 N·m (60–80 in-lbs). For International Applications: Place the fog lamp switch label (3) on the clutch control clamp. | 
Figure 5. Install Wiring Harness (FXDWG shown) 
Figure 6. Install Lamp Switch (1996-later shown) | ||||||||||||||||||||||
| 17. | See Figure 10. Secure the lamp switch leg of the harness to the handlebar using the wire harness retainers (Item 18) as needed. Snap the retainers into the holes in the handlebar. | |||||||||||||||||||||||
| 18. | Remove the headlamp assembly following the instructions in the service manual. NOTE When wired as follows, the auxiliary lamps can only be operated while the main headlamp is on low beam. This conforms to many state and local laws. | |||||||||||||||||||||||
| 19. | See Figure 7. Route the unterminated wire (1) from the switch through the grommet into the headlight housing. Splice it to the yellow (low beam) wire (2) using the Scotchlok® electrical connector (Item 14) from the kit. NOTE To route the wire through the grommet, push a hooked piece of wire through the grommet from the inside of the headlamp housing. Soap the toggle switch wire and pull it back through the grommet with the hooked wire. In some applications the wire from the kit harness may not fit through the headlight housing grommet. If this is the case, splice the black wire to the yellow wire outside the headlight housing, then tape the connector to shield it from moisture. | 
Figure 7. Splice Unterminated Wire from the Switch to Headlight Yellow Wire | ||||||||||||||||||||||
| 20. | Install the headlamp assembly following the instructions in the service manual. | |||||||||||||||||||||||
| 21. | See Figure 8 and Figure 9 , and the SEALED SPLICE CONNECTORS section of the service manual. Slide the heat-shrink tubing (1) over the white wire (2) from the kit harness, and crimp the electrical connector (3) to the wire with a Crimp Tool, Part No. H-D 38125-8. | |||||||||||||||||||||||
| 22. | Bring both lamp wires (4) to the connector. Trim the wires, allowing approximately 1 inch (25 mm) of the wire to extend past the butt splice connector. Trim the conduit (5) approximately 1-1/2 in. (38 mm) back from the end of the wire. | |||||||||||||||||||||||
| 23. | Remove approximately 3/8 in. (10 mm) of insulation from the end of the lamp wires. | |||||||||||||||||||||||
| 24. | Insert the ends of both lamp wires (4) into the electrical connector (3) and crimp the wires to the connector with the crimp tool. NOTE Protect the heat-shrink tubing from the heat source while applying heat to the electrical connector. | |||||||||||||||||||||||
| WARNING Be sure to follow manufacturer's instructions when using the UltraTorch UT-100 or any other radiant heating device. Failure to follow manufacturer's instructions can cause a fire, which could result in death or serious injury. (00335a) | ||||||||||||||||||||||||
| 25. | Slide the heat-shrink tubing (1) away from the splice and using the UltraTorch UT-100 (H-D 39969), Robinair Heat Gun (H-D 25070) with Heatshrink Attachment (H-D 41183), or other suitable radiant heating device, heat the crimped splice to encapsulate the butt splice connection. Apply heat from the center of the crimp out to each end until the meltable sealant exudes out of both ends of the connector. Let the connector cool. | |||||||||||||||||||||||
| 26. | Slide the heat-shrink tubing back over the splice and using the same radiant heating device, heat the tubing to encapsulate the butt splice connection. Apply heat from the center of the tubing out to each end. | |||||||||||||||||||||||
| WARNING Be sure that steering is smooth and free without interference. Interference with steering could result in loss of vehicle control and death or serious injury. (00371a) | ||||||||||||||||||||||||
| 27. | See Figure 10. Secure the wires to the lower fork steering bracket using the adhesive-backed clips (15) from the kit. | |||||||||||||||||||||||
| 28. | Install the fuel tank following the instructions in the service manual. | |||||||||||||||||||||||
| 29. | Connect the battery cables, positive cable first. | |||||||||||||||||||||||
| WARNING After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) | ||||||||||||||||||||||||
| 30. | Refer to the service manual and follow instructions to install the seat. | |||||||||||||||||||||||
| WARNING The automatic-on headlamp feature provides increased visibility of the rider to other motorists. Be sure headlamp is on at all times. Poor visibility of rider to other motorists can result in death or serious injury. (00030b) | ||||||||||||||||||||||||
| 31. | Test headlamp high and low beams, and the auxiliary lamps for proper operation. Aim the auxiliary lamps and tighten the lamp mounting nuts. |
| 1 | Heat shrink tubing |
| 2 | White wire from kit harness |
| 3 | butt splice connector |
| 4 | Lamp wires |
| 5 | Conduit |
Figure 8. Connect the Lamp Wires to the Kit Harness
| 1 | Stripped wire ends inserted in connector |
| 2 | Wire ends crimped in connector |
| 3 | Connector after heat has been applied |
Figure 9. Installing Sealed Butt Splice Connectors
SERVICE PARTS
Figure 10. Service Parts: Chrome Auxiliary Lamp Kit
Table 1. Service Parts Table
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Passing lamp housing (2) | 68276-02 |
2 | Sealed unit (purchased separately) | |
3 | Bracket, lamp mounting (right) | Not Sold Separately |
4 | Clamp, lamp mounting (right) | Not Sold Separately |
5 | Bracket, lamp mounting (left) | Not Sold Separately |
6 | Bracket, lamp mounting (left) | Not Sold Separately |
7 | Screw, socket-head, 1/4-20 x 3/4 in, locking (4) | 927A |
8 | Clamp block, auxiliary lamp (2) | 68720-62 |
9 | Lockwasher, internal tooth, 3/8 in. (2) | 7130W |
10 | Retainer, lamp mounting (2) | Not Sold Separately |
11 | Boot, switch | 67880-94 |
12 | Label, lamp switch, HDI only | 68604-01 |
13 | Connector, pre-insulated, sealed, butt splice | 70586-93 |
14 | Connector, electrical (Scotchlok®, blue) | 70576-68 |
15 | Clip, adhesive-backed (4) | 10102 |
16 | Cable strap, 7/8 in (198 mm) (12) | 10102 |
17 | Shrink tube | 72266-94 |
18 | Harness retainer (4) | 70345-84 |
19 | Bracket, switch mounting | Not Sold Separately |
20 | Conduit, vinyl, 15 in (38.1 cm) (2) | Not Sold Separately |
21 | Wiring harness assembly | 69104-04A |
22 | Ring terminal (2) | 9858 |
23 | Switch | 70370-00 |
24 | Trim ring | 68725-62A |
25 | Screw | 3514 |
26 | Nut | 7606 |
27 | Inner nesting ring | 68331-02 |
28 | B+ jumper harness | 69200013 |