SE120R SCREAMIN' EAGLE PRO RACE-USE CRATE ENGINE
J054832014-07-16
GENERAL
Kit Number
19289-12
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
NOTICE
Installation of this kit requires jetting changes or recalibration for proper function. Failure to do so may cause a lean fuel condition, which may result in engine damage. (00623b)
NOTE
This engine is for race use only! Remove the emissions label and license plate from the factory chassis.
This engine has been assembled with a Dyna Sprocket Shaft Spacer (Part No. 24038-03).
Installation Requirements
- Recommended synthetic engine oil, Screamin' Eagle SYN3® 20W50 (Part No. 99824-03/00QT).
- Touring models require replacement of Sprocket Shaft Spacer with Part No. 24008-03 for 2002-2005 models or Part No. 24009-06 for 2006 models.
- The cylinder heads in this kit are machined for use with symmetric intake flanges (original equipment since 2006). 1999-2005 models require separate purchase of symmetric intake seal flanges (Part No. 26993-06), quantity 2.
- Installation of compression releases is required. Refer to Screamin' Eagle Pro Catalog or contact a Harley-Davidson dealer.
- A clutch kit that supports a minimum of 190 N·m (140 ft-lbs) of torque. Harley-Davidson recommends installation of Screamin' Eagle pressure clutch (Part No. 37000121) and diaphragm spring (Part No. 37951-98). Drag racing applications use clutch kit (Part No. 37976-08A).
- SE throttle body, Air Cleaner and High Flow injectors. Refer to the Screamin' Eagle Pro Catalog or contact a Harley-Davidson dealer.
- SE exhaust gaskets kit (Part No. 17048-98).
- Oil cooler is recommended. See P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
- EFI Models: SE Pro Super Tuner - refer to Screamin' Eagle Pro Catalog or contact a Harley-Davidson dealer.
- See appropriate sections in service manual for the special tools required to install this kit.
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
PREPARATION
NOTE
For vehicles equipped with security siren:
- Verify that the hands-free Fob is present.
- With security fob present, turn ignition switch ON.
EFI Models:
WARNINGTo prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a)
Purge and disconnect fuel supply line.
For ALL Vehicles:
WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a)
WARNINGDisconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a)
- See the service manual to remove the seat. See the service manual to disconnect the battery cables, negative cable first. Retain all seat mounting hardware.
For Carbureted Models:
WARNINGGasoline can drain from the carburetor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a)
- Turn the fuel supply valve to OFF. Remove the fuel line from the valve.
REMOVAL
Remove OE Engine
| 1. | Raise the motorcycle. | |
| WARNING When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) | ||
| 2. | Remove the fuel tank according to the instructions in the service manual. | |
| 3. | Refer to ENGINE section of the appropriate service manual for removal of engine from chassis. |
SE120R ENGINE INSTALLATION
- Before installing the engine, make sure that there is no debris or contaminates in the oiling system. See service manual to flush-out the oil tank. Have the tank flush-out performed by an authorized dealer or qualified technician.
- Remove the oil passage caps/plugs at the engine to transmission interface.
- Refer to the ENGINE section of the appropriate service manual for installation of the engine to the chassis.
- For Touring Models: Remove sprocket shaft spacer and replace with appropriate spacer listed in ADDITIONAL PARTS REQUIRED section.
Final Assembly
| 1. | Install the fuel tank according to the instructions in the service manual. | |
| 2. | Install the seat according to the instructions in the service manual. | |
| WARNING After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) NOTICE You must recalibrate the ECM when installing this kit. Failure to properly recalibrate the ECM can result in severe engine damage. (00399b) | ||
| 3. | Download the new ECM calibration when installing this kit. Refer to the Screamin' Eagle Pro Catalog or contact a Harley-Davidson dealer. | |
| 4. | Start and run the engine. Repeat several times to verify proper operation. |
OPERATION
- Refer to BREAK-IN RIDING RULES in the owner's manual to break-in the new engine.
MAINTENANCE
- Refer to the MAINTENANCE SCHEDULE in the appropriate service manual or owner's manual.
- Refer to ENGINE section of service manual for assembly and disassembly.
SE120R ENGINE SPECIFICATIONS
NOTE
The following sections provide unique information not available in the service manual ENGINE section for the appropriate Twin Cam 96™ alpha engines from Touring or Dyna platforms.
Table 1. Engine: SE Twin Cam 120R
Item | Specification | |
|---|---|---|
Compression Ratio | 10.5:1 | |
Bore | 4.060 in | 103.12 mm |
Stroke | 4.625 in | 117.48 mm |
Displacement | 119.75 cu in | 1962.39 cc |
Lubrication system | Pressurized dry sump with oil cooler | |
MANUFACTURING TOLERANCES
Refer to the Twin-Cam 96™ specifications in the service manual for any specification not shown in the following tables.
Table 2. Cylinder Heads
ITEM | IN. | MM |
|---|---|---|
Valve guide in head (tight) | 0.0020-0.0033 | 0.051-0.084 |
Intake valve seat in head (tight) | 0.004-0.0055 | 0.102-0.140 |
Exhaust valve seat in head (tight) | 0.004-0.0055 | 0.102-0.140 |
Table 3. Valves
ITEM | IN. | MM |
|---|---|---|
Fit in guide (intake and exhaust) | 0.0011-0.0029 | 0.028-0.074 |
Seat width | 0.034-0.062 | 0.86-1.57 |
Stem protrusion from cylinder head boss | 1.990-2.024 | 50.55-51.41 |
Table 4. Valve Springs Specifications
ITEM | PRESSURE | DIMENSION |
|---|---|---|
Closed | 180 lbs (79 kg) | 1.800 in. (45.7 mm) |
Open | 500 lbs (196 kg) | 1.177 in. (29.9 mm) |
Free length | n/a | 2.210 in. (56.1 mm) |
Table 5. Pistons
Piston Clearance: | IN. | MM |
|---|---|---|
Piston-to-cylinder fit (Loose) | 0.0026-0.0036 | 0.066-0.091 |
Piston pin fit (Loose) | 0.0003-0.0008 | 0.007-0.020 |
Top Ring End Gap Second Ring End Gap Oil Control Ring Rail Gap | 0.012-0.020 0.016-0.024 0.008-0.028 | 0.304-0.505 0.406-0.609 0.203-0.711 |
Top Ring Side Clearance Second Ring Side Clearance Oil Control Ring Side Clearance | 0.0010-0.0022 0.0010-0.0022 0.0003-0.0072 | 0.025-0.055 0.025-0.055 0.007-0.182 |
Table 6. Cam Specifications - SE266E
Intake | Specification |
|---|---|
Opens | 24 BTDC |
Closes | 58 ABDC |
Duration | 262o |
Max. Valve Lift | 0.658 in (16.713 mm) |
Valve Lift @ TDC | 0.208 in (5.283 mm) |
Exhaust | Specification |
Opens | 69 BBDC |
Closes | 17 ATDC |
Duration | 266o |
Max. Valve Lift | 0.658 in (16.713 mm) |
Valve Lift @ TDC | 0.178 in (4.521 mm) |
Cam Timing @ 0.053 in (1.346 mm) of Tappet Lift in Crankshaft Degrees | |
SERVICE WEAR LIMITS
Use wear limits as guide to part replacement.
NOTE
Refer to the Twin-Cam 96 specifications in the service manual for any specification not shown in the following tables
Table 7. Cylinders
ITEM | REPLACE IF WEAR EXCEEDS | |
|---|---|---|
IN. | MM | |
Taper | 0.002 | 0.051 |
Out of round | 0.002 | 0.051 |
Warpage of gasket or O-ring surfaces: top | 0.006 | 0.152 |
Warpage of gasket or O-ring surfaces: base | 0.004 | 0.102 |
Table 8. Cylinder Bore
ITEM | REPLACE IF WEAR EXCEEDS | |
|---|---|---|
IN. | MM | |
Standard | 4.062 | 103.17 |
0.010 in. oversize | 4.072 | 103.43 |
Table 9. Pistons
Piston-to-cylinder Fit Wear Limit (Loose) | IN. | MM |
|---|---|---|
Fit in cylinder (Loose) | 0.0061 | 0.155 |
Piston Pin Fit (Loose) | 0.0011 | 0.028 |
Top Ring End Gap Second Ring End Gap Oil Control Ring Rail Gap | 0.030 0.034 0.038 | 0.762 0.863 0.965 |
Top Ring Side Clearance Second Ring Side Clearance Oil Control Ring Side Clearance | 0.0030 0.0030 0.0079 | 0.076 0.076 0.200 |
SERVICING OR REPLACING SE120R CYLINDERS
| 1. | Raise the motorcycle. NOTE Disarm security system. | |
| 2. | Remove seat according to the instructions in the service manual. | |
| WARNING When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) | ||
| 3. | Remove main fuse. Refer to service manual for your motorcycle. | |
| 4. | Remove fuel tank according to the instructions in the service manual. |
Remove Engine Components
- Refer to service manual to remove existing air cleaner assembly.
- Remove the existing exhaust system following service manual procedures.
- Disassemble the engine top end. Refer to the appropriate engine sections in the service manual.
Install Engine Top End Components
NOTE
See Figure 1. The 4.060 in cylinder base gasket (1) and cylinder head gasket (2) eliminate the need for O-rings. Do not use O-rings on cylinder dowels or cylinder spigots.
When installing new base gasket (1), install with the embossed side down and the concave side up.
| 1. | Refer to the appropriate service manual and assemble the engine with the following changes: a. Assemble the top end of the engine using the base gaskets and head gaskets provided in the kit. Refer to the appropriate engine section in the service manual. | 
Figure 1. Cylinder Gaskets |
Final Assembly
| 2. | Install the fuel tank according to the instructions in the service manual. | |
| 3. | Refer to the service manual to install the main fuse. | |
| WARNING After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) | ||
| 4. | Install the seat according to the instructions in the service manual. |
SERVICING OR REPLACING SE120R PISTON
- Refer to ENGINE section of service manual.
INSTALLATION
WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a)
WARNINGDisconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a)
| 1. | See the service manual to remove the seat. See the service manual to disconnect the battery cables, negative cable first. | |||||
| WARNING When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) | ||||||
| 2. | Refer to the ENGINE: STRIPPING MOTORCYCLE FOR SERVICE and TOP END OVERHAUL, DISASSEMBLY sections of the service manual for cylinder head, cylinder and piston removal procedures. | |||||
| 3. | Follow the procedures in the ENGINE: SUB-ASSEMBLY SERVICE AND REPAIR, TOP END/ CYLINDER/ UPPER CONNECTING ROD sections of the service manual for inspection of parts. | |||||
| 4. | See the ENGINE: SUB-ASSEMBLY SERVICE AND REPAIR, CYLINDER section of the service manual for boring and honing instructions. NOTE Install the top ring (barrel-faced) and second ring (taper-faced Napier) with the "N" marking facing up. Oil ring rails can be installed either side up. The 4.060 in cylinder base gaskets and cylinder head gaskets included in the kit eliminate the need for O-rings (Part No. 11273). Do
not use O-rings on cylinder dowels or cylinder spigots. When installing new base gasket, install with the embossed side down and the concave side up. NOTE Checking piston-to-cylinder fit at this location per Table 5 for reference. | 
Figure 2. Piston Measurements | ||||
| 5. | See Figure 2. Measure the piston width (1), 90 degrees horizontally from both sides of the piston pin hole and 1.275 in down from the deck surface (top) of the piston (2). See Table 5 for piston-to-cylinder fit at this location. | |||||
| 6. | The pistons in this kit are front and rear specific. Install the piston marked "FRONT" in the front cylinder with the arrow pointing towards the front of the engine. Install the piston marked "REAR" in the rear cylinder with the arrow pointing towards the front of the engine. | |||||
| 7. | Refer to the ENGINE: TOP END OVERHAUL, ASSEMBLY section of the service manual for piston, cylinder and cylinder head installation procedures. |
Piston Pin Retaining Ring (Circlip) Installation
NOTE
Circlip gap must be at 12 or 6 o'clock position when installed.
| 8. | See Figure 3. Insert the open end of the circlip (1) into the notch (2) on the groove (3) around the piston pin boss so the gap is at the 12 or 6 o'clock position when installed. | 
Figure 3. Circlip and Piston 
Figure 4. Install Circlip | ||||||||||
| 9. | See Figure 4. Position your thumb (1) as shown. Press firmly until approximately 85% of the circlip (2) is seated in the groove. | |||||||||||
| 10. | Do not scratch or mar the piston, use a small-bladed screwdriver to wedge the circlip into the remainder of the groove. Repeat for the remaining circlips. NOTE Make sure that the piston circlip is fully seated, or ENGINE DAMAGE WILL OCCUR. | |||||||||||
| 11. | Refer to the ENGINE: ASSEMBLING MOTORCYCLE AFTER STRIPPING section of the service manual for final reassembly procedures. |  Figure 5. Piston Assembly |
Table 10. Piston Assembly
Item | Description (Quantity) |
|---|---|
1 | Piston (front, standard) |
2 | Piston (rear, standard) |
3 |
|
4 |
|
5 |
|
1 | Piston (front, +0.010) |
2 | Piston (rear, +0.010) |
3 |
|
4 |
|
5 |
|
REPLACING/SERVICING PUSHRODS
| 1. | Refer to ENGINE section of service manual. NOTE Follow the appropriate service manual procedures for installing or removing the pushrods. The pushrods are marked Intake and Exhaust. The pushrods are directional. Verify that the larger ends of the pushrods are installed down in the lifter sockets. | 
Figure 6. Push Rods |
REPLACING/SERVICING CYLINDER HEADS
- Refer to ENGINE section of service manual.
- Apply Loctite 246 Medium Strength/High Temperature Threadlocker and Sealer (purchased separately) to screws and install the "120R" medallions. Tighten to 1.1–2.3 N·m (10–12 in-lbs)
NOTE
See Figure 9. Replacement cylinder heads (1) have "CNC PORTED" medallions. If desired, reuse or purchase new "120R" medallions (12).
SERVICE PARTS
Figure 7. Engine Assembly, SE120R Complete
Table 11. SE120R Screamin' Eagle Pro Race-Use Crate Engine
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Engine assembly, complete | 19289-12 |
Figure 8. Service Parts: SE120R Screamin' Eagle Pro Race-Use Crate Engine
Table 12. Service Parts: SE120R Screamin' Eagle Pro Race-Use Crate Engine
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Base gasket, cylinder (2) | 16736-04A |
2 | SE cylinder kit, 4.060 in., (black) (includes items 1, 3, 4, 1105 and 1086A) | 16550-04C |
3 | Dowel pin, ring (4) | 16595-99A |
4 | Gasket, cylinder head (2) | 16104-04 |
5 | Stud, cylinder (8) | 16834-99A |
6 | Gasket kit, engine overhaul (does not include cylinder head gasket, base gasket or valve stem seals) (Not Shown) | 17053-99C |
7 | Gasket kit, top-end, (does not include cylinder head gasket, base gasket or valve stem seals) (Not Shown) | 17052-99C |
Figure 9. Service Parts: SE120R Screamin' Eagle Pro Race-Use Crate Engine
Table 13. Service Parts: SE120R Screamin' Eagle Pro Race-Use Crate Engine
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Cylinder head assembly, rear with "CNC PORTED" medallion (includes items 2 through 11) | 16921-11 |
Cylinder head assembly, front with "CNC PORTED" medallion (includes items 2 through 11) | 16917-11 | |
2 |
| Not Sold Separately |
3 |
| See Service Kits |
4 |
| See Service Kits |
5 |
| 16715-83 |
6 |
| 18190-08 |
7 |
| 18183-03 |
8 |
| 18046-98 |
9 |
| See Service Kits |
10 |
| 18240-98 |
11 |
| 16648-08 |
12 | Medallion, "120R" | 17136-10 |
13 | Screw, button head, TORX (2) | 94634-99 |
14 | Screw, internal thread, 3-3/16 inch (4) | 16478-85A |
15 | Screw, internal thread, 1-7/8 inch (4) | 16480-92A |
16 | Spark plugs (not shown) (2) | 32186-10 |
Service Kits: | ||
A | Valve Spring Kit, Screamin' Eagle | 18281-02A |
The following Screamin' Eagle parts are available separately: | ||
B | Valve seat, intake | 18191-08 |
C | Valve seat, exhaust | 18048-98A |
D | Valve guide, intake (for service) | |
| 18158-05 | |
| 18156-05 | |
| 18154-05 | |
E | Valve guide, exhaust (for service) | |
| 18157-05 | |
| 18155-05 | |
| 18153-05 | |
Figure 10. SE120R Screamin' Eagle Pro Race-Use Crate Engine
Table 14. Service Parts: SE120R Screamin' Eagle Pro Race-Use Crate Engine
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Screw 5/16-18 X 2-1/2 hex flange head (grade 8) (8) | 1039 |
2 | Screw 5/16-18 X 1.0 hex head, with lockpatch (6) | 3692A |
3 | Screw 5/16-18 X 1-3/4 hex head, with lockpatch (10) | 3693A |
4 | Screw 5/16-18 X 1-1/4 hex flange head, with lockpatch (8) | 3736B |
5 | Screw 1/4-20 X 1-11/16 hex head (grade 8), with lockpatch, (4) | 4400 |
6 | Screw 1/4-20 X 1 socket head, with lockpatch (8) | 4741A |
7 | Washer 11/16 X 29/32 X 1/32 (4) | 6762B |
8 | O-ring, push rod cover (4) | 11132A |
9 | O-ring, push rod cover (4) | 11145A |
10 | O-ring (2) | 11270 |
11 | O-ring (4) | 11293 |
12 | Gasket, rocker housing (2) | 16719-99B |
13 | Gasket kit, cam service | 17045-99D |
14 | Rocker arm, front intake, rear exhaust, with bushings (2) | 17360-83A |
15 | Rocker arm, rear intake, front exhaust, with bushings (2) | 17375-83A |
16 | Gasket, rocker cover (2) | 17386-99A |
17 | Bushing, rocker arm (8) | 17428-57 |
18 | Rocker cover, (chrome) (2) | 17572-99 |
19 | Rocker housing, (chrome) (2) | 17578-10 |
20 | Lifter cover, front (chrome) Lifter cover, rear (chrome) | 17964-99 17966-99 |
21 | Support, rocker arm (2) | 17594-99 |
22 | Breather assembly (2) | 17025-03A |
23 | Shaft, rocker arm (4) | 17611-83 |
24 | Perfect Fit push rod kit (+0.030 inch) | 18401-03 |
25 | Cover, push rod, lower (4) | 17939-99 |
26 | Cap, cover spring (4) | 17945-36B |
27 | Spring, push rod cover (4) | 17947-36 |
28 | Cover, push rod upper (4) | 17948-99 |
29 | Retainer, spring cap (4) | 17968-99 |
30 | Pin, anti-rotation (2) | 18535-99 |
31 | Hydraulic lifter kit (Includes 4 lifters) | 18572-13 |
32 | Gasket, lifter cover (2) | 18673-07 |
33 | Baffle assembly, breather (2) | 26500002 |
Figure 11. Service Parts; SE120R Screamin' Eagle Pro Race-Use Crate Engine
Table 15. Service Parts: SE120R Screamin' Eagle Pro Race-Use Crate Engine
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Retaining ring | 11177A |
2 | Piston ring set, standard (2) Piston ring set, 0.010 inch over size (2) | 22526-10 22529-10 |
3 | Piston kit, front and rear, with ring sets, piston pin and lock rings, standard Piston kit, front and rear, with ring sets, piston pin and lock rings, 0.010 inch over size | 22574-10 22576-10 |
4 | Lock ring, piston pin (4) | 22097-99 |
5 | Piston pin (2) | 22310-10 |
6 | Flywheel assembly kit | 24100007 |
Figure 12. Service Parts: SE120R Screamin' Eagle Pro Race-Use Crate Engine
Table 16. Service Parts: SE120R Screamin' Eagle Pro Race-Use Crate Engine
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Plug (3) | 765 |
2 2a 2b | Screw, 5/16-18 x 3.0 inch, hex flange head (8) Screw, top center crankcase Washer, sealing | 895 1105 1086A |
3 | Washer (3) | 6099 |
4 | Washer 1-1/4 x 1-53/64 x 1/8 (2) | 8972 |
5 | Needle bearing kit, (kit contains 2) | 24017-10 |
6 | O-ring (2) | 10930 |
7 | O-ring (2) | 11293 |
8 | Oil seal | 12068 |
9 | Dowel pin (2) | 16574-99A |
10 | Dowel pin (2) | 16589-99A |
11 | Dowel pin (4) | 16595-99A |
12 | Piston cooling jet, with 10930 (2) | 22315-06A |
13 | Bearing kit, left side with 8972, 24605-07, 35114-02, and inner race | 24004-03B |
14 | Spacer, sprocket shaft (Dyna models only) | 24038-03 |
15 | Crankcase set, (black) with 5, 12, 13, 16, 22, 24 and 3983 bolts (not shown) | 24400031 |
16 | Bearing, main (2) | 24605-07 |
17 | Oil filter mount kit, with lockplate kit, adapter and O-rings | 26261-99 |
18 | Fitting, straight (3) | 26314-99 |
19 | Adapter, oil filter | 26352-95A |
20 | O-Ring (2) | 26432-76A |
21 | Lockplate kit with screws, O-rings and washers | 35071-99 |
22 | Retaining ring | 35114-02 |
23 | Oil filter (chrome) | 63798-99A |
24 | Screw, TORX® 8-32 x 3/8 (4) | 68042-99 |
Figure 13. Service Parts: SE 120R Screamin' Eagle Pro Race-Use Crate Engine
Table 17. Service Parts: SE120R Screamin' Eagle Pro Race-use Crate Engine
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Roll pin | 601 |
2 | Screw, primary cam chain tensioner (2) | 942 |
3 | Screw, cam cover, 1/4-20 x 1-1/4, knurled with lockpatch (grade 8), (10) Screw, secondary cam tensioner, 1/4-20 x 1-1/4, knurled with lockpatch (grade 8), (2) | 4740A 4740A |
4 | Screw, 1/4-20 x 1, socket head, with lockpatch (8) | 4741A |
5 | Washer, 3/8 x 1-1/8 x 7/32 | 6294 |
6 | Bearing assembly with bearing, inner race, washer and O-ring | 8983 |
7 | Needle bearing kit, (kit contains 2) | 24017-10 |
8 | O-ring | 11293 |
9 | O-ring (2) | 11301 |
10 | Retaining ring | 11494 |
11 | Gasket kit, cam service | 17045-99D |
12 | Cam drive sprocket retention kit, with 6294, screws and washer | 25566-06 |
13 | Plate, bearing retaining | 1200018 |
14 | Gasket, cam cover | 25244-99A |
15 | Cam support plate, with bypass valve | 25400018 |
16 | Cam cover, (chrome) | 25369-01B |
17 | Camshaft chain and fastener kit, with 25566-06, 25673-06, 25675-06 and 25728-06 | 25585-06 |
18 | Camshaft, front and rear kit, SE266E | 25400029 |
19 | Screw, 8-32 x 3/8 TORX head (5) | 68042-99 |
20 | Sprocket, cam drive on crankshaft, 17 T | 25673-06 |
21 | Chain, primary cam drive | 25675-06 |
22 | Chain, secondary cam drive | 25607-99 |
23 | Sprocket, cam drive, 34 T | 25728-06 |
24 | Ball bearing | 8990A |
25 | Spacer, cam drive sprocket alignment 0.287 inch thick Spacer, cam drive sprocket alignment 0.297 inch thick Spacer, cam drive sprocket alignment 0.307 inch thick Spacer, cam drive sprocket alignment 0.317 inch thick Spacer, cam drive sprocket alignment 0.327 inch thick Spacer, cam drive sprocket alignment 0.337 inch thick Spacer, cam drive sprocket alignment 0.347 inch thick Spacer, cam drive sprocket alignment 0.357 inch thick | 25722-00 25723-00 25721-00 25719-00 25717-00 25725-00 11889 11890 |
26 | Oil pump assembly | 62400001 |
27 | Spring, relief valve | 26210-99 |
28 | Relief valve, oil pump | 26400-82B |
29 | Cover, 120R | 25495-10 |
30 | Chain tensioner, primary cam drive chain | 39968-06 |
31 | Chain tensioner, secondary cam drive chain | 39969-06 |
32 | Spring, separator | 40323-00 |