0/0
PAINT GUARD KIT
J060002014-05-20
GENERAL
Kit Number
11100125
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Harley-Davidson recommends that this kit is professionally installed.
Kit Contents
See Figure 1 and Table 1.
Installation Requirements
Separate purchase of two one-quart spray bottles, JOHNSON & JOHNSON® Baby Shampoo and 70% isopropyl alcohol.
Separate purchase of a 3M Squeegee (3M part number 71607 or equivalent) is required for proper installation of this kit.
PREPARATION
NOTE
Prepare solutions on the day of installation.
  1. Prepare two solutions in spray bottles:
  • Slip Solution: Thoroughly mix 16 oz (473 mL) of distilled water and 2-3 drops of baby shampoo. The solution should sheet off the paint guards with minimum froth.
  • Tack Solution: Using 70% isopropyl rubbing alcohol, mix a solution that is 10% alcohol and 90% distilled water.
  1. See Figure 1. Wash all mounting areas throughly. Allow to dry completely.
Installation Tips and Tricks
  • Do not apply to new paint (including touch-up paint). Allow paint to cure for a minimum of 30 days before applying the paint guards.
  • Do not apply in windy conditions or in direct sunlight.
  • Install when ambient temperature is between 60-90 °F (15-32 °C).
  • Wash hands throughly and keep fingers wet with water/shampoo mixture during installation. To avoid fingerprints, do not touch adhesive with dry fingers.
  • Keep paint guard film and squeegee wet during installation.
  • See Figure 1. Identify each paint guard piece and its mounting location before proceeding. The paint guard pieces are side-specific.
  • Start with the top of the piece.
  • When smoothing the paint guards into place with the squeegee, work from the top edge toward the bottom edge. Continually spray the paint guards with solution during the installation.
  • The soap solution allows the paint guard to be slightly repositioned.
  • The alcohol solution fixes the adhesive to the lids and can slightly stretch the paint guard film.
  • If wrinkles are found after applying the alcohol solution, spray more alcohol solution under the wrinkle and squeegee again.
INSTALLATION
NOTE
Start with the top edge of the piece.
  1. Wet the mounting surface and fingers thoroughly with the soap solution.
  2. See Figure 1. Align the paint guard with the top edge of the saddlebag.
  3. Roll a small section of the paper backing away from the adhesive surface. Spray the adhesive surface with soap solution. Align with a straight edge of the mounting surface. When aligned properly, slow roll the remaining backing from the film.
  4. When the backing is fully removed, spray the entire paint guard film with soap solution and smooth the film into place by hand.
    5. NOTE
    If repositioning is needed, spray more of the soap solution on the paint guard and hands and position as necessary.
  5. Once positioned properly, gently lift the leading edge of the film about half-way.
  6. Spray the film and mounting surface with the water/alcohol mixture.
  7. Starting from the top edge work toward the bottom edge, use the squeegee to remove air bubbles. Use firm and overlapping strokes with the squeegee to work out all the air. Do not cut or tear the film.
  8. Gently lift the other side of the film and repeat Steps 6 and 7.
  9. Wipe paint guard dry with a Harley-Davidson® Microfiber Detailing Cloth (94663-02). Check for water pockets or air bubbles. If necessary, spray with more alcohol solution and squeegee again. If necessary, the paint guard film can still be lifted to reposition. Spray the paint guard film, the mounting surface and your fingers with the alcohol solution. Squeegee again until all water pockets and air bubbles are removed.
  10. Repeat all steps for the other paint guard piece.
FINAL INSTALLATION
  1. Check the edges for adhesion. If any area is not adhered, wrap the squeegee with a Harley-Davidson® Microfiber Detailing Cloth (94663-02) and squeegee the edges again.
  2. Allow the paint guards to cure for 24 hours. The paint guards can then be washed and waxed with the same products recommended for the motorcycle. See the motorcycle owner's manual for recommended products.
SERVICE PARTS
Figure 1. Service Parts: Paint Guard Kit
Table 1. Kit Contents
Item
Description (Quantity)
Part Number
1
Fender, front, left and right (right side shown)
Not Sold Separately
2
Fender, inner, left and right (right side shown)
Not Sold Separately
3
Side cover, left and right (left side shown)
Not Sold Separately
4
Body, left and right (left side shown)
Not Sold Separately
5
Fender, outer, left and right (left side shown)
Not Sold Separately