BLADE FRONT WHEEL KITS
J054492012-10-24
GENERAL
WARNINGInstall only wheels and installation kits approved for your model motorcycle. Contact a Harley-Davidson dealer to verify fitment. Mismatching wheels and installation kits or installing wheels not approved for your model can cause loss of control, which could result in death or serious injury. (00610c)
Kit Numbers
43300008, 43300034
Models
For model fitment information, see the P&A Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
NOTE
Accessory hub caps are not compatible with this wheel style.
Kit Contents
These kits include the custom wheel. See Table 1 for kit contents.
Additional Parts Required
Proper installation of this kit requires the separate purchase of the following parts which are available at a Harley-Davidson dealer:
- 10 Brake Disc/Hub Cap Screws (3762M) and 10 washers (6966M) or 2 Chrome screw kits (91800029)
- Wheel Bearing Remover and Installer (94134-09A)
The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning:
- Harley® Bright™ Chrome Cleaner (94683-99)
- Harley® Glaze™ Polish and Sealant (99701-84)
- Harley® Wheel and Spoke Brush (43078-99)
- Harley-Davidson® Wheel and Tire Cleaner (94658-98)
- Harley® Preserve™ Bare Aluminum Protectant (99845-07)
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
INSTALLATION
| 1. | Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. NOTE Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems. | |
| 2. | See Figure 1. Install valve stem assembly (L ) on wheel. Refer to TIRES in service manual. NOTE Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The side with the DOT marking is the primary bearing side. Proper installation of these kits requires the separate purchase of two floating brake discs (44343-01 for 2004 - 2007 models and 44553-06A (stock) or 41500012 (polished) for 2008 and later models) and a tire (43371-07 on 2004-2008 models and 44026-09A on 2009-later models). The left side of the wheel is the primary bearing side, the side opposite from the location of the valve stem hole. For 2008 and later Touring: Install bearing shim (43903-08) under the primary bearing. | |
NOTICE Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) | ||
| 3. | Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual. | |
| 4. | Install previously removed wheel spacers. Refer to FRONT WHEEL in service manual. | |
| 5. | Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. |
MAINTENANCE AND CLEANING
Chrome parts must be maintained regularly to verify that they keep their original shine and luster.
- Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush.
- Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner.
- After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant.
SERVICE PARTS
Figure 1. Service Parts: Blade Front Wheel Kits
Table 1. Service Parts and Wheel Kit Contents
Kit | Item | Description (Quantity) | Part Number |
|---|---|---|---|
43300008, 43300034 | 1 | Wheel | Not Sold Separately |
Table 2. FRONT 1 Inch Bearing Wheel Installation Kit (43848-08A)
FRONT 1 Inch Bearing Wheel Installation Kit (43848-08A) | ITEM (Quantity Used and Description) | |||||||
|---|---|---|---|---|---|---|---|---|
Fitment | Wheel Size | A | C | D | E | F | L | M |
2000-2007 Touring | 16 x 3.0 in | 2 | 1 | 0 | 0 | 0 | * | * |
2004-2007 Touring | 18 x 3.5 in | 2 | 1 | 0 | 0 | 0 | * | * |
2004-2005 Dyna (except FXDWG) | 19 x 2.5 in | 2 | 0 | 0 | 0 | 1 | * | * |
2006-2007 Dyna (except FXDWG) | 19 x 2.5 in | 2 | 0 | 0 | 1 | 0 | * | * |
2002-2007 VRSC | 19 x 3.0 in | 2 | 0 | 0 | 1 | 0 | * | * |
2006-2007 FXDWG** | 21 x 2.15 in | 2 | 0 | 1 | 0 | 0 | * | * |
2004-2005 Dyna (except FXDWG) | 21 x 2.15 in | 2 | 0 | 0 | 0 | 1 | * | * |
Installation kits are designed to work with many different wheel styles and fitments. Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on. NOTES: * See NOTE above valve installation step in INSTALLATION to determine which valve stem to use for your particular kit. Discard other valve stem(s). ** The right side of the wheel is the primary bearing side for this fitment. | A | Bearing, regular (2) | 9247 | |||||
C | Axle sleeve | 43517-00 | ||||||
D | Axle sleeve | 43633-06 | ||||||
E | Axle sleeve | 43641-01 | ||||||
F | Axle sleeve | 43755-04 | ||||||
L | Valve stem, short | 43157-83A | ||||||
M | Valve stem, long | 43206-01 | ||||||
Table 3. FRONT 25 mm Bearing Wheel Installation Kit (41455-08C)
FRONT 25 mm Bearing Wheel Installation Kit (41455-08C) | ITEM (Quantity Used and Description) | ||||||||
|---|---|---|---|---|---|---|---|---|---|
Fitment | Wheel Size | A | C | D | J | K | L | M | N |
2008 Touring; 2009 and later FLHRC (non-ABS) and Trike (non-ABS) | 16 x 3.0 in | 2 | 0 | 1 | 0 | 1 | * | * | * |
2009 and later Touring (non-ABS) | 17 x 3.0 in | 2 | 0 | 1 | 0 | 0 | * | * | * |
2008 and later Touring (non-ABS) | 18 x 3.5 in | 2 | 0 | 1 | 0 | ** | * | * | * |
2008 and later Dyna (except FLD, FXDWG and FXDF) | 19 x 2.5 in | 2 | 1 | 0 | ** | 0 | * | * | 0 |
2008 and later VRSCAW, VRSCD, VRSCF and VRSCDX (non-ABS) | 19 x 3.0 in | 2 | 1 | 0 | ** | 0 | * | * | 0 |
2009 and later Touring (non-ABS) | 19 x 3.5 in | 2 | 0 | 1 | 0 | 0 | * | * | * |
Installation kits are designed to work with many different wheel styles and fitments. Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on. NOTES: * See NOTE above valve installation step in INSTALLATION to determine which valve stem to use for your particular kit. Discard other valve stem(s). ** See NOTES for your wheel kit above the wheel assembly step in INSTALLATION to determine if bearing shim is used for your particular wheel kit and fitment. *** Bearing shim installed under the primary bearing. | A | Bearing, regular (2) | 9276 | ||||||
C | Axle sleeve | 41748-08 | |||||||
D | Axle sleeve | 41900-08 | |||||||
J | Bearing shim*** | 41450-08 | |||||||
K | Bearing shim*** | 43903-08 | |||||||
L | Valve stem, short | 43157-83A | |||||||
M | Valve stem, long | 43206-01 | |||||||
N | Valve stem, pull thru | 40999-87 | |||||||
Table 4. FRONT 25 mm Bearing ABS Wheel Installation Kit (41454-08B)
FRONT 25 mm Bearing ABS Wheel Installation Kit (41454-08B) | ITEM (Quantity Used and Description) | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
Fitment | Wheel Size | A | B | C | D | J | K | L | M | N |
2008 Touring and 2009 and later FLHRC with ABS | 16 x 3.0 in | 1 | 1 | 0 | 1 | 0 | 1 | * | * | 0 |
2009 and later Touring with ABS | 17 x 3.0 in | 1 | 1 | 0 | 1 | 0 | 0 | * | * | * |
2008 and later Touring with ABS | 18 x 3.5 in | 1 | 1 | 0 | 1 | ** | ** | * | * | * |
2012 and later Dyna with ABS (Except FLD, FXDWG and FXDF) | 19 x 2.5 in | 1 | 1 | 1 | 0 | ** | ** | * | * | 0 |
2008 and later VRSCAW, VRSCD, VRSCF and VRSCDX with ABS | 19 x 3.0 in | 1 | 1 | 1 | 0 | ** | ** | * | * | 0 |
2009 and later Touring with ABS | 19 x 3.5 in | 1 | 1 | 0 | 1 | 0 | 0 | * | * | * |
Installation kits are designed to work with many different wheel styles and fitments. Contact a Harley-Davidson dealer to verify that the wheel and installation kits are both designed and approved for the motorcycle they are being installed on. NOTES: * See NOTE above valve installation step in INSTALLATION to determine which valve stem to use for your particular kit. Discard other valve stem(s). ** See NOTES for your wheel kit above the wheel assembly step in INSTALLATION to determine which bearing shim to use for your particular wheel kit and fitment. *** Red side of bearing must be installed toward the wheel. The ABS bearing is primary. **** Bearing shim installed under the primary bearing. | A | Bearing, regular | 9276 | |||||||
B | Bearing, ABS*** | 9252 | ||||||||
C | Axle sleeve | 41748-08 | ||||||||
D | Axle sleeve | 41900-08 | ||||||||
J | Bearing shim**** | 41450-08 | ||||||||
K | Bearing shim**** | 43903-08 | ||||||||
L | Valve stem, short | 43157-83A | ||||||||
M | Valve stem, long | 43206-01 | ||||||||
N | Valve stem, pull thru | 40999-87 | ||||||||