All models require the relocation of the rear turn signals. Refer to instructions included with an appropriate turn signal relocation kit for your model motorcycle.

Models equipped with side-mount license plate also require the relocation of the license plate. Refer to instructions included with the license plate relocation kit for your model motorcycle.

See Figure 7 and Table 1. Obtain the saddlebag support arms (10) and docking clips (19).

See Figure 2 Install the U-shaped docking clips (1) to the slot end of the saddlebag support arms (2). Clips must be fully inserted in the support arm slot to fit over the docking clevis.

Make sure that docking clip protrusions are fully seated in the support arm notch (3) and both ends of the docking clip are roughly even with the support arm fingers (4). Multiple attempts to position the clips may be needed. IF the clip is close but not fully seated, pliers may be used, protecting the clip and bracket surfaces, to force the notches to engage.

See Figure 3. Install Docking Hardware Kit 90201424 referring to instructions included in that kit.

See Figure 7 and Table 1. Obtain the right (1) and left (2) saddlebag assemblies, rear docking adapters (14), screws (13) and nuts (15).

See Figure 4. Insert the posts of the rear docking adapter (1) into holes into the rear of the saddlebag bracket and hold in place.

Install rear docking adapter (1) using screw (2) and nut (3). Tighten snugly.

See Figure 7 and Table 1. Obtain the saddlebag support arms with attached u-clips (10 and 19), flat washers (12), lockwashers (11) and components from kit 90201424.

Follow instructions from kit 90201424 to assembly arm (10) to the saddlebags.

Proceed to "Saddlebag Installation".

Refer to instructions included with Docking Hardware Kit 90201424.

Install the docking points per instructions in docking kit 90201424.

Install the saddlebag support arm assemblies per instructions in docking kit 90201424.

See Figure 5. Unlock and unclip the saddlebag lid and open the saddlebag.

Pull on knob (1) located in upper rear corner inside saddlebag. Rotate knob toward rear of saddlebag (clockwise for left side saddlebag, counterclockwise for right side saddlebag).

Approach the motorcycle with the saddlebag tipped slightly forward. Align the support arm slot over the docking clevis at the passenger foot support.

Swing body of saddlebag down to align the forward and rear saddlebag bracket slots to the outer docking points. Slide into slots of bracket on back of saddlebag.

Slide the saddlebag forward making sure that it is fully seated into all three docking locations.

Rotate knob roughly 90 degrees forward relative to the saddlebag until the knob and latch assembly spring-load into place.

Repeat for opposite side saddlebag assembly.

See Figure 6. Position reflector mount (1) in center of saddlebag.

Mark holes on saddlebag with pen or other suitable tool.

Clean the surface of the reflector mount (1) with a mixture of 50-70 percent isopropyl alcohol and 30-50 percent distilled water. Allow to dry completely.

Remove the liner from the adhesive backing of the reflector (2). Carefully position the reflector to the reflector mount. Press firmly into place. Hold the reflector in position with steady pressure for at least one minute.

Using a suitable tool, make two 3/16 in holes in saddlebag at locations marked in Step 2.

Install reflector mount (1) on saddlebag using two push nuts (3). The push nuts are installed from inside the saddlebag.

See Figure 7 and Table 1. Obtain the lock items 3 through 7 from the kit.

Unclip and open one of the saddlebag lids for access to the lock opening.

See Figure 6. Place the lock face washer (5) over the lock cylinder (4).

Install the lock cylinder so the key notches of the lock face (12) are oriented at the 12 o'clock and 9 o'clock positions. Insert lock cylinder through hole in saddlebag lid and engage flat surfaces (11) of both lock and lid support plastic backing.

Install the lock retainer (6) from the inside of the saddlebag lid and over the lock cylinder.

With lock cylinder inserted through the saddlebag lid and retainer washer in place against the inside of the lid, apply a few drops of Loctite 243 (blue) to the 3-4 lock cylinder threads nearest to the lock retainer washer.

Install the locknut (7) from the inside of the lid and thread onto the lock cylinder. Tighten securely.

Remove the pawl nut (10) and star washer (9) from the installed lock cylinder (4). Do not remove the cam washer from the back of the lock cylinder. If the cam falls off the lock cylinder, it must be replaced correctly. Correct installation allows the key to be removed in both the locked and unlocked positions. The cam can be installed incorrectly so test the orientation before installation of the pawl. If the key is unable to be removed in either lock position, flip the cam over and install.

Install the lock pawl (8) to the threaded post of the lock cylinder as well as a star washer (9) and pawl nut (10). Tighten pawl nut securely.

Repeat the lock installation for the other saddlebag.

After approximately 500 miles of on road use with the saddlebags installed, check the torque on the docking point mounting screws. Check to make sure that the proper torque is maintained and tighten screws as necessary.

Apply the Harley-Davidson Genuine Leather Dressing (H-D Part Number 93600034) included with the saddlebag according to the instructions in the leather care kit.

Periodically oil saddlebag snaps using a small amount of motor oil or all-purpose household oil.