SHORTY DUAL ACCESSORY SLIP-ON MUFFLER KITS
J060952015-02-18
GENERAL
Kit Numbers
64900342, 64900343
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
Proper installation of these kits requires separate purchase of two muffler clamps (H-D Part No. 65296-95A).
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet refers to service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
PRODUCT INFORMATION
Tampering Prohibition
Federal law prohibits any modifications to this exhaust system which cause the motorcycle to exceed Federal noise standards. Use of a motorcycle with such a modified exhaust system is also prohibited.
Noise Emission Warranty
Harley-Davidson warrants that these mufflers, at the time of sale, meet all applicable United States E.P.A. Federal Noise and Emissions standards. This warranty extends to the original purchaser for purposes other than resale, and to all subsequent buyers. Direct warranty claims to an authorized Harley-Davidson dealer.
NOTE
To avoid penalties under state and local ordinances, repair or replace this product if motorcycle noise increases significantly through use.
PREPARATION
WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
NOTE
- WITH security siren: With security fob present, turn ignition switch ON. See the service manual. After system is disarmed, turn ignition switch OFF. IMMEDIATELY remove the main fuse.
- WITHOUT security siren: See the service manual. Remove main fuse.
REMOVAL
- See Figure 1. Loosen muffler clamps (A).
- Apply penetrating oil to seams of mufflers (1, 2) and exhaust pipes.
- Black exhaust system: Remove muffler shield clamps (B) to detach muffler shields (3) from mufflers.
- ALL exhaust systems: Remove muffler fasteners (D) to detach mufflers from muffler support (C).
- Slide mufflers rearward off pipes. Discard clamps (A).
INSTALLATION
| 1. | See Figure 1. Place new muffler clamps (A) over exhaust pipes. | |
| 2. | Slide mufflers (1, 2), onto exhaust pipes. | |
| 3. | Align mufflers to tabs on muffler support (C). Install muffler fasteners (D). Tighten to 10.9–13.6 N·m (96–120 in-lbs). | |
| 4. | Tighten muffler clamps (A) to 51.6–58.4 N·m (38–43 ft-lbs). | |
NOTICE Wipe all fingerprints off of exhaust system components after installation and before starting engine. Oil from hands can leave permanent marks on exhaust system finish. (00346a) | ||
| 5. | Wipe exhaust system clean. | |
| 6. | Black exhaust system: Open muffler shield clamps (B). Install the muffler shields (3). Position clamps so the screws are on the outboard side in the most accessible position. |
COMPLETION
NOTE
Verify that the ignition is OFF before installing the main fuse.
| 1. | See the service manual. Install main fuse. | |
| WARNING After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) | ||
| 2. | See the service manual. Install seat. |
SERVICE PARTS
Table 1. Service Parts
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Muffler assembly, front | Not sold separately |
2 | Muffler assembly, rear | Not sold separately |
3 | Muffler shield, black, front/rear (2) (for black mufflers) | 65400078 |
Items mentioned in text, but not included in kit. | ||
A | Muffler clamp (2), Part No. 65296-95A (Purchase separately) | |
B | Original equipment (OE) hose clamp, black (4), Part No. 10800010 (for black mufflers) | |
C | OE interconnect tube assembly, Part No. 66737-10A | |
D | OE muffler fastener screw (4), Part No. 3391 | |
E | OE interconnect tube fastener (2) | |
F | OE interconnect gasket (2), Part No. 65830-10 | |
G | OE exhaust shield (2) | |
SERVICE PARTS
Figure 1. Service Parts, Shorty Dual Style Accessory Slip-On Mufler Kits