BOOM! TRIKE BODY SPEAKER INSTALLATION KIT
J060992016-05-12
GENERAL
Dealer installation is recommended.
Kit Number
76000617
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
Separate purchase of more parts or accessories may be required for proper installation of this kit. These can be purchased separately from a Harley-Davidson dealer.
Amplifier Kit (part number 76000277). Instructions for amplifier installation are covered in this document.
If installing more than TWO amplifiers, a Battery+ Three-Way Y Connector (Part No. 70270-04A, available separately) is needed. ONE Battery+ Three-Way Y Connector can be used for up to three (3) more amplifiers
NOTE
DO NOT mix Stage I and Stage II speakers on the same vehicle.
NOTICE
Radio EQ MUST be updated by a Harley-Davidson dealer BEFORE operating the audio system. Operating the audio system prior to radio EQ update will IMMEDIATELY damage the speakers. (00645d)
Radio EQ update using the Digital Technician® II diagnostic tool is:
- Recommended before speaker INSTALLATION
- Required before audio system OPERATION.
- Only available through authorized Harley-Davidson dealers.
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
Electrical Overload
WARNINGWhen installing any electrical accessory, be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modified. Exceeding the maximum amperage can lead to electrical failures, which could result in death or serious injury. (00310a)
NOTICE
It is possible to overload the vehicle's charging system by adding too many electrical accessories. If the combined electrical accessories operating at any one time consume more electrical current than the vehicle's charging system can produce, the electrical consumption can discharge the battery and cause damage to the vehicle's electrical system. (00211d)
This amplifier requires up to 8 amps more current from the electrical system.
The purchase of this kit entitles you to a specially developed sound equalization software that is used with the Advanced Audio System. This unique equalization was designed to optimize the performance and sound response of the BOOM! Audio fairing lower speakers. Even if this kit is not installed by a Harley-Davidson dealer, this special equalization software is available without charge from any dealer through Digital Technician II. Dealer labor rates may apply for the upgrade procedure.
PREPARATION
WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
- Remove main fuse. See the service manual.
- Remove seat. See the service manual.
- Remove passenger grab rail. See the service manual.
- Remove side covers. See the service manual.
- Remove body and place on protective pad. See the service manual. The fenders and Tour-Pak can remain attached to the body.
INSTALLATION
NOTE
The template is used for both sides of the body.
Verify that no wire harness or metal clips reside on the inside surfaces. If metal wire retention clips are present (especially on vehicle left side), use chisel and hammer to remove the clips.
| 1. | See Figure 1. Align template (1) with one side of the trike body (2). Edges of the template align to tangent edges of the body work rounds. Secure the template with tape (3). Centerpunch the eight small hole (4) locations. Mark the large hole (5) with a contrasting marker or grease pencil. | 
Figure 1. Template Location | ||||||||||||||
| 2. | Remove the template. Use a 7/32 in (5.6 mm) drill bit to make the eight small holes. Use an air saw (or equivalent) to cut the center opening. | |||||||||||||||
| 3. | Flip template and repeat previous steps for the other side. NOTE If concurrent installation of Stage II Amplifier installation kit for Trike Tour-Pak pods, use rectangular template provided in that kit to cut hole for grommet. Hole in main Trike body for the left side enclosure provides greater access to use 25.4 mm (1.0 in) drill bit. | |||||||||||||||
| 4. | Interior side only lightly sand the surface of the body around the center and bolt hole openings verifying a good gasket surface. Proper surface preparation helps reduce buzzing, squeaking or rattling caused by the increased sound pressure of your BOOM! audio system. | |||||||||||||||
| 5. | See Figure 5. Install bracket (3) to connector side of amplifier (amplifier sold separately). Secure with screws (12). Tighten screws to 9.4–12.2 N·m (7–9 ft-lbs). | |||||||||||||||
| 6. | Install bracket (19) to non-connector side of amplifier (amplifier sold separately). Secure with screws (12). Tighten screws to 9.4–12.2 N·m (7–9 ft-lbs). | |||||||||||||||
| 7. | See Figure 2. Position the amplifier and brackets (1) over the four raised pads (4 and 7). Position the connector toward the vehicle left side as shown. Center the lower holes over the lower pads (4). | |||||||||||||||
| 8. | Mark the hole locations. Remove amplifier with brackets. Drill four holes with 9/32 in (7.2 mm) drill bit. | |||||||||||||||
| 9. | Clean all surfaces of the body work with 50-70% isopropyl alcohol and 30-50% distilled water. Allow to dry completely. | |||||||||||||||
| 10. | Speaker enclosure installation. a. See Figure 5. Place one gasket (18) on the exterior surface. Align the holes. b. Place a trim ring (14) over gasket and center hole. (Left side trim ring is marked "A". Right side trim ring is marked "B".) Rotate trim ring so the letter is at the bottom. c. Position the correct enclosure (17 or 4) with a gasket inside the body. d. Reach through the center hole. Align the holes in the enclosure, gasket (18) and body. Insert plastite screw (13) through a counterbored hole. e. Tighten plastite screw two or three turns. Enough turns to allow the enclosure to dangle. f. Insert a plastite screw in the counterbored hole opposite of the first screw. Align the enclosure, gaskets, body trim ring and screw. Rotate the screw several times to hold enclosure in place. g. Insert plastite screws in the two remaining counterbored holes. Align the enclosure, gaskets, body trim ring and screws. Rotate the screw several times to hole enclosure in place. h. Tighten plastite screws in an alternating pattern. Tighten to 2.2 N·m (20 in-lbs). | |||||||||||||||
| 11. | Repeat previous steps to install the other side enclosure and components. | |||||||||||||||
| 12. | See Figure 2. Place a washer (5) on screws (6). Install through holes from the inside of the trunk. From the outside of the trunk, place an extra washer (5) over the top screws only to act as a spacer. Position the amplifier and brackets (1) over the four raised pads (4 and 7). Position the connector toward the vehicle left side. Install washers (2) over the brackets and screws. Secure with nut (3). Tighten nut to 10.8–12.2 N·m (96–108 in-lbs). | 
Figure 2. Amplifier Installation | ||||||||||||||
| 13. | See Figure 3. Route existing wire (16). | |||||||||||||||
| 14. | Connect wire harness to amplifier. | |||||||||||||||
| 15. | See Figure 3 and Figure 4. Route harness for speakers and amplifier. Secure wires as necessary. | |||||||||||||||
| 16. | Position body onto frame. See service manual. Body can remain unsecured until all wiring is complete. NOTE If the body is removed later for service, the harness must be disconnected from the main vehicle/frame. It may be left connected to the amplifier and speakers. NOTE Configure harness to match amplifier. Incorrect harness configuration can cause improper EQ file to load and damage speakers. Locate configuration wire [32] along the main harness. Verify the male and female terminals are not connected. | |||||||||||||||
| 17. | Complete Routing harness: a. Route kit harness forward along frame rails following main harness under backbone. b. Route harness along the right side of battery cavity between the battery and reverse solenoid. Place the red fuse wire and black ground wire in front of the battery. c. Route Digital Tech connectors in front of the battery and over to the left side cover. Attach connector [91B] to Digital Tech input on the OE harness. Connector [91A] serve as the new Digital Tech input. d. Attach (+) and (-) battery cables. If more than two amplifiers are on the vehicle, One Battery+ Three-Way Y-Connector (available separately) is required. NOTE If concurrent installation of Stage II Amplifier installation kit for Trike Tour-Pak pods, attach connector [91B] of one harness to the OE vehicle (DLC connector). Connect [91A] of the first harness into [91B] of the second harness and route in front the battery compartment. Route [91A] of the second harness over to the side cover to serve as the new Digital Tech input. Which harness is designated the first or second harness is not relevant. | |||||||||||||||
| 18. | Connect amplifier input: a. Stage I 6-speaker configuration: Install harness [296] directly into the 16-way harness (previously installed through fairing amplifier kit), located behind the passenger seat. Stage II 6-speaker configuration: Install 3-way interconnect harness (item 15, Figure 5 ) into the 16-way harness (previously installed through fairing amplifier kit), located behind the passenger seat. Install harness [296] into 3-way interconnector. |
| 1 | Amplifier connector |
| 2 | RH Speaker woofer connectors |
| 3 | RH Speaker mid/tweeter connector [36TB] |
| 4 | Amp configuration setting connector [32] |
| 5 | Positive battery terminal [B+] |
| 6 | Negative battery terminal [B-] |
| 7 | New Digital Technician connector [91A] |
| 8 | Digital Tech connector [91B] to OE harness |
| 9 | Audio input connector [296] |
| 10 | LH Speaker mid/tweeter [37TB] |
| 11 | LH Speaker connectors |
| 12 | Right side speaker enclosure |
| 13 | Left side speaker enclosure |
| 14 | Center notch |
| 15 | Body mounting hardware |
| 16 | Wire, existing |
| 17 | Wire bracket, existing |
Figure 3. Wire Harness (viewed from bottom up)
| 1 | Amplifier connector |
| 2 | Left side speaker (woofer) connectors |
| 3 | Left side speaker (mid/tweeter) connector [36TB] (stage II only) |
| 4 | Inline configuration wire connector |
| 5 | Positive battery terminal [B+] |
| 6 | Negative battery terminal [B-] |
| 7 | New Digital Technician connector [91A] |
| 8 | Digital Tech connector [91B] to OE harness |
| 9 | Audio input connector [296] |
| 10 | Right side speaker (mid/tweeter) connector [37TB] (stage II only) |
| 11 | Right side speaker (woofer) connectors |
| 12 | Left side speaker enclosure |
| 13 | Right side speaker enclosure |
| 14 | Right side frame tube and reverse module |
| 15 | Inline B+ connector |
Figure 4. Wire Harness and Connectors
NOTICE
Radio EQ MUST be updated by a Harley-Davidson dealer BEFORE operating the audio system. Operating the audio system prior to radio EQ update will IMMEDIATELY damage the speakers. (00645d)
- Install the body. See the service manual.
- Install passenger grab rail. See the service manual.
- Install side covers. See the service manual.
- See the service manual. Install seat. After installing seat, pull up on the seat to verify that it is secure.
- Install main fuse. See the service manual.
DIGITAL TECHNICIAN NOTES
- With the harness configured properly, the amplifier installed in this kit is recognized as AMP 2. Even though this amplifier may be the second or third amplifier physically installed. See Figure 4 In order for Digital Technician to recognize amplifier 2 connector (4) See must be unplugged.
- When used with Stage I speakers, channels 3 & 4 shows open. Channel 1 is. Left speaker, channel 2 is right speaker.
- When used with Stage II speakers: channel 1 is left woofer. Channel 2 is right woofer, channel 3 remains mid/tweeter, channel 4 is right mid/tweeter.
SERVICE PARTS
Figure 5. Service Parts, Speaker Expansion Installation Kit
Table 1. Service Parts
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Screw (4) | 2513 |
2 | Washer (6) | 6036 |
3 | Bracket, amp mount, connector side | Not sold separately |
4 | Speaker enclosure, left side | Not sold separately |
5 | Tie strap (9) | 10006 |
6 | Bracket, wire retainer (4) | 69200342 |
7 | Template | 76000628 |
8 | Wire harness, amplifier | Not sold separately |
9 | Nut, nylock | 7686 |
10 | Washer (4) | 6110 |
11 | Screw (8) | 2963 |
12 | Screw (4) | 926 |
13 | Screw, plastite (8), #8-16 x 1 in. | Not sold separately |
14 | Trim ring, (left "A") | 76000612 |
Trim ring, (right "B") | 76000611 | |
15 | Wire harness, audio input | Not sold separately |
16 | Grommet, round (2) | 12100071 |
17 | Speaker enclosure, right side | Not sold separately |
18 | Gasket, speaker enclosure (4) | 76000619 |
19 | Bracket, amp mount, non-connector side | Not sold separately |
Wiring Diagram Information
Wire Color Codes
For Solid Color Wires: See Connector/Wiring Diagram Symbols (Typical) . The alpha code identifies wire color.
For Striped Wires: The code is written with a slash (/) between the solid color code and the stripe code. For example, a trace labeled GN/Y is a green wire with a yellow stripe.
Wiring Diagram Symbols
See Connector/Wiring Diagram Symbols (Typical) . Brackets [] indicate connector numbers. The letter inside the brackets identifies whether the housing is a socket or pin housing.
A=Pin: The letter A and the pin symbol after a connector number identifies the pin side of the terminal connectors.
B=Socket: The letter B and the socket symbol after a connector number identifies the socket side of the terminal connectors. Other symbols found on the wiring diagrams include the following:
Diode: The diode allows current flow in one direction only in a circuit.
Wire break: The wire breaks are used to show option variances or page breaks.
No Connection: Two wires crossing over each other in a wiring diagram that are shown with no splice indicating they are not connected together.
Circuit to/from: This symbol indicates a complete circuit diagram on another page. The symbol is also identifying the direction of current flow.
Splice: Splices are where two or more wires are connected together along a wiring diagram. The indication of a splice only indicates that wires are spliced to that circuit. It is not the true location of the splice in the wiring harness.
Ground: Grounds can be classified as either clean or dirty grounds. Clean grounds are identified by a (BK/GN) wire and are normally used for sensors or modules.
NOTE
Clean grounds usually do not have electric motors, coils or anything that may cause electrical interference on the ground circuit.
Dirty grounds are identified by a (BK) wire and are used for components that are not as sensitive to electrical interference.
Twisted pair: This symbol indicates that the two wires are twisted together in the harness. This minimizes the circuit's electromagnetic interference from external sources. If repairs are necessary to these wires, they should remain as twisted wires.
| 1 | Connector number |
| 2 | Terminal code (A=pin, B=socket) |
| 3 | Solid wire color |
| 4 | Striped wire color |
| 5 | Socket symbol |
| 6 | Pin symbol |
| 7 | Diode |
| 8 | Wire break |
| 9 | No connection |
| 10 | Circuit to/from |
| 11 | Splice |
| 12 | Ground |
| 13 | Twisted pair |
Figure 6. Connector/Wiring Diagram Symbols
Table 2. Wire Color Codes
ALPHA CODE | WIRE COLOR |
|---|---|
BE | Blue |
BK | Black |
BN | Brown |
GN | Green |
GY | Gray |
LBE | Light Blue |
LGN | Light Green |
O | Orange |
PK | Pink |
R | Red |
TN | Tan |
V | Violet |
W | White |
Y | Yellow |
| 1 | Amplifier connector [149B] |
| 2 | Inline B+ connector |
| 3 | Amplifier fuse |
| 4 | Left side speaker (mid/tweeter) connector [36TB] (stage II only) |
| 5 | Left side speaker (woofer) connectors [36B] |
| 6 | Digital Tech connector [91B] |
| 7 | New Digital Technician connector [91A] |
| 8 | Audio input connector [296B] |
| 9 | Right side speaker (mid/tweeter) connector [37TB] (stage II only) |
| 10 | Right side speaker (woofer) connectors [37B] |
| 11 | Inline B- connector |
| 12 | Negative ring terminal [B-] |
| 13 | Positive ring terminal [B+] |
Figure 7. Main Amplifier Wiring Schematic
| 1 | Secondary amplifier input |
| 2 | Secondary amplifier output |
| 3 | Secondary amplifier output |
| 4 | Secondary amplifier output |
Figure 8. Audio Input Harness