DETACHABLES LOCK KITS
J057182022-08-08
GENERAL
Kit Numbers
90300086, 90300087
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
Separate purchase of additional parts or accessories may be required for proper installation of this kit on certain model motorcycles. See the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only) for a list of required items for a specific model.
NOTE
Use one latch per accessory installation. A second latch is included for an additional accessory.
PREPARATION
- Refer to Table 1 to determine the installation configuration for a specific model, year and type of detachable.
LATCH SWAP
On certain models and accessories, first swap the right and left non-locking latches (see Table 1 to determine if this is recommended for your application). This will change the clockwise and counterclockwise motion to attach and remove the accessory. By changing the latch rotation, the lock mechanism points toward the rear of the vehicle and provide greater key access.
- See Figure 1. Remove right non-locking latch (1). Leave right spring washer (5) on right mounting hub (2).
- Remove left non-locking latch (3). Leave left spring washer (6) on left mounting hub (4). Install left non-locking latch (3) on right mounting hub (2).
- Install right non-locking latch (1) on left mounting hub (4).
REMOVAL
- Remove the detachable accessory by pressing the release button on each side pulling the latch levers back. Lift the rear of the accessory up removing the rack from the front docking points.
- See Figure 2. Remove screw (1) and washer (2) from the latch being replaced. Save the screw and washer for installation.
NOTE
Some accessories have two washers per side. Save both.
| 1 | Right non-locking latch |
| 2 | Right mounting hub |
| 3 | Left non-locking latch |
| 4 | Left mounting hub |
| 5 | Right spring washer |
| 6 | Left spring washer |
| 7 | Hex socket head screw (2) |
| 8 | Flat washer (2) |
Figure 1. Latch Swap (Before Swap Configuration Shown)
| 1 | Screw |
| 2 | Washer |
| 3 | Spring washer(s) |
| 4 | Accessory sideplate (typical) |
Figure 2. Remove Latch (Outer Right Installation Shown)
INSTALLATION
Table 1. Installation Table
Model | Fitment | Detachable* | Installation |
|---|---|---|---|
Sportster | 1994 - 2003 | Sideplate Kit | See Figure 7, Inner Right Installation (Relief Hidden) |
2004 - Later | Sideplate Kit | See Figure 8, Latch Swap and Inner Right Installation | |
1994 - Later | Solo Rack Kit | See Figure 7, Inner Right Installation (Relief Hidden) | |
Softail | 1984 - Later | Sideplate Kit | See Figure 7, Inner Right Installation (Relief Hidden) |
1984 - Later (except FXCW/C) | Solo Rack Kit | See Figure 7, Inner Right Installation (Relief Hidden) | |
2006 - Later (except 2011 - Later FLS/FXS) | One-Piece Sissy Bar Kit | See Figure 7, Inner Right Installation (Relief Hidden) | |
2011 - Later FLS/FXS | One-Piece Sissy Bar Kit | See Figure 6, Inner Left Installation | |
2000 - Later | Tour-Pak (2-Up or Solo) | See Figure 6, Inner Left Installation | |
Dyna | 1996 - Later (including 1993 - Later FXDWG) (except 2012 - Later FLD) | Sideplate Kit | See Figure 7, Inner Right Installation (Relief Hidden) |
2012 - Later FLD | Sideplate Kit | See Figure 6, Inner Left Installation | |
2006 - Later | One-Piece Sissy Bar Kit | See Figure 7, Inner Right Installation (Relief Hidden) | |
Solo Rack Kit | See Figure 7, Inner Right Installation (Relief Hidden) | ||
Touring | 2009 - Later | Sissy Bar Upright Kit | See Figure 6, Inner Left Installation |
Two-Up Luggage Rack Kit | See Figure 4, Outer Left Installation, OR Figure 3, Outer Right Installation | ||
Two-Up Tour-Pak Rack | See Figure 3, Outer Right Installation | ||
1994 - 2008 | Sissy Bar Upright Kit | See Figure 3, Outer Right Installation | |
1997 - 2008 | Two-Up Luggage Rack Kit | See Figure 1, Latch Swap AND Figure 5, Inner Right Installation | |
Solo Luggage Rack Kit | See Figure 3, Outer Right Installation | ||
Two-Up Tour-Pak Rack | See Figure 1, Latch Swap AND Figure 5, Inner Right Installation | ||
Solo Tour-Pak Rack | See Figure 1, Latch Swap AND Figure 4, Outer Left Installation | ||
* For detachable part numbers, see the P&A catalog. | |||
See Figure 9. Depending on the installed detachable, the position of the relief (A) and undercuts (B) are used as spacers or docking point mounts. Verify that the locking latch is positioned so there is key access for unlocking the latch.
NOTE
Verify that the locking latch is in the unlocked position before installation. Do not leave the key inserted in the locking latch during assembly.
Detachable styles may vary from illustrations.
Outer Right Installation
NOTE
Verify that the outer right latch rotates clockwise to close (counterclockwise to open). If not, see Outer Left Installation.
| 1. | Remove right non-locking latch. | |||||||||
| 2. | See Figure 3. Install original spring washer (2) on mounting hub. | 
Figure 3. Outer Right Installation | ||||||||
| 3. | Install flat washer (4) from kit on mounting hub. | |||||||||
| 4. | Install latch with relief away from the outer right sideplate. | |||||||||
| 5. | Install original screw and washer (1). | |||||||||
| 6. | Tighten screw. Torque: 3.4–4.5 N·m (30–40 in-lbs) Hex socket head screw |
Outer Left Installation
NOTE
Verify that the outer left latch rotates clockwise to close (counterclockwise to open). If not, see Outer Right Installation.
| 1. | See Figure 4. Remove left non-locking latch and discard. | |
| 2. | Install flat washer (5) from kit over spring washer on left mounting hub. | |
| 3. | Install locking latch (3) on left mounting hub with relief away from the sideplate. | |
| 4. | Install original screw (1) and washer (2). | |
| 5. | Tighten screw. Torque: 3.4–4.5 N·m (30–40 in-lbs) Hex socket head screw |
| 1 | Original screw |
| 2 | Original washer |
| 3 | Locking latch |
| 4 | Non-locking latch |
| 5 | Flat washer |
| 6 | Spring washer |
Figure 4. Outer Left Installation
Inner Right Installation
| 1. | See Figure 5. Remove right non-locking latch and discard. | |||||||||
| 2. | Install flat washer (4) from kit over spring washer on right mounting hub. | |||||||||
| 3. | Install latch with relief away from the sideplate. | |||||||||
| 4. | Install original screw and washer (1). | |||||||||
| 5. | Tighten screw. Torque: 3.4–4.5 N·m (30–40 in-lbs) Hex socket head screw | 
Figure 5. Inner Right Installation |
Inner Left Installation
| 1. | Remove left non-locking latch. | |||||||||
| 2. | See Figure 6. Install spring washer (3) on left mounting hub. | |||||||||
| 3. | Install flat washer (4) from kit on mounting hub. | |||||||||
| 4. | Install latch with relief away from the inner left sideplate. | |||||||||
| 5. | Install original screw and washer (1). | |||||||||
| 6. | Tighten screw. Torque: 3.4–4.5 N·m (30–40 in-lbs) Hex socket head screw | 
Figure 6. Inner Left Installation |
Inner Right (Relief Hidden) Installation
| 1. | See Figure 7. Remove right non-locking latch. Leave the right spring washer on the right mounting hub. | |
| 2. | Install locking latch with relief facing right sideplate. DO NOT use the spacer from the kit. | |
| 3. | Install original screw and washer. | |
| 4. | Tighten screw. Torque: 3.4–4.5 N·m (30–40 in-lbs) Hex socket head screw |
| 1 | Original screw and washer(s) |
| 2 | Locking latch |
| 3 | Spring washer |
Figure 7. Inner Right (Relief Hidden) Installation
| 1 | Original screw (2) |
| 2 | Original washer (2) |
| 3 | Original spring washer (2) |
| 4 | Spacer (locking latch side) |
| 5 | Locking latch |
| 6 | Non-locking latch |
Figure 8. Inner Right Installation
OPERATION
Locking and Unlocking the Latch
NOTE
Make sure that the key is not in the latch during installation of the detachable.
Key is not required to lock the latch.
- Locking the Latch: See Figure 9. When the detachable is installed, push the spring-operated lock (C).
- Unlocking the Latch: Insert the key in the lock and turn it gently clockwise 1/8 of a turn. Turn the key counterclockwise 1/8 of a turn and remove key.
NOTE
Keep the key (3) aligned with the post of the release button (D) while unlocking the latch. Avoid bending or breaking the key or the shaft.
SERVICE PARTS
Figure 9. Service Parts: Detachables Lock Kits
Table 2. Service Parts: Detachables Lock Kits
Item | Description (Quantity) | Part Number |
|---|---|---|
Kit Number 90300086 | ||
1 | Latch, locking, black (2) | Not sold separately |
2 | Flat washer (2) | Not sold separately |
3 | Key, short (1) | Not sold separately |
4 | Key, long (1) | Not sold separately |
Kit Number 90300087 | ||
1 | Latch, locking, chrome (2) | Not sold separately |
2 | Flat washer (2) | Not sold separately |
3 | Key, short (1) | Not sold separately |
4 | Key, long (1) | Not sold separately |
Items referenced in text: | ||
A | Relief | |
B | Undercut (2) | |
C | Lock, spring-operated | |
D | Release button | |
HARLEY-DAVIDSON KEY REPLACEMENT PROGRAM
Key Replacement
NOTE
- Always separate the keys and the key tags.
- Copy the key number in the space provided.
- Store this document in a safe place.
Replacement keys can only be obtained through an authorized Harley-Davidson dealership.
Replacement keys are sold in pairs. (One short key and one long key rung together.) Need key code to know which part number to order.
Harley-Davidson Key Number: ______________
Purchase Date: ____________________________________
Table 3.
Key Code | H-D Part Number |
|---|---|
2391 | 90300178 |
2392 | 90300179 |
2393 | 90300180 |
2394 | 90300181 |
2395 | 90300182 |
2396 | 90300183 |
2397 | 90300184 |
2398 | 90300185 |