BLACK LED FRONT BULLET TURN SIGNAL KIT
J065802017-11-08
GENERAL
Kit Number
67800977
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
Electrical Overload
NOTICE
It is possible to overload the vehicle's charging system by adding too many electrical accessories. If the combined electrical accessories operating at any one time consume more electrical current than the vehicle's charging system can produce, the electrical consumption can discharge the battery and cause damage to the vehicle's electrical system. (00211d)
WARNING
When installing any electrical accessory, be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modified. Exceeding the maximum amperage can lead to electrical failures, which could result in death or serious injury. (00310a)
At 13.5V, the current draw is 169mA. The current draw may vary up to 241mA dependent on battery voltage.
Kit Contents
See Figure 3 and Table 1.
Additional Parts Required
PREPARATION
1. Remove main fuse. See service manual.
2. Remove front turn signals. See service manual.
3. Remove and retain the lenses and mounting ball hardware from existing turn signals.
INSTALLATION
See Figure 3. Two of the wires are already connected to the socket housing, refer to following steps based on vehicle specifications:
1. Domestic: Insert the loose terminal on the end of the wire into the cavity of the socket housing: Blue turn signal wire to Cavity 1, see Figure 2. Install the seal plug (1) in the unused slot of the connector housing.
2. International: Install the seal plugs (1) in the unused slots of the connector housing. Place the heat shrink (5) over the blue turn signal wire terminal and apply heat.
1Headlamp security siren [38]
2Console [20]
3TGS [204]
4Right front lighting [31R]
5Front WSS [167]
6Left front lighting [31L]
7USB caddy interconnect [329]
8LHCM [24]
9RHCM [22-1]
10RHCM [22-2]
Figure 1. USB Caddy
1Socket housing
2Socket terminal
3Tab
4Lock
Figure 2. JAE Connector
ALL Models:
3. Assemble the mounting ball hardware and lenses on new turn signal assemblies.
4. Apply threadlocker to the screws removed earlier.LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
5. Install the screws. Tighten.
Torque: 4.5–5.4 N·m (40–48 in-lbs)
NOTE
Over tightening screws can crack the lens.
6. Route wiring through the handlebars.
7. See Figure 1. Connect right front turn signal connector [31R] (4) and left front turn signal connector [31L] (6).
8. Install fuse. See the service manual.
WARNING
Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a)
BCM Programming Process
1. See the service manual. Follow procedure for clearing BCM codes.
2. Program the BCM. The BCM can self-learn if LED turn signals are installed when the Hazards are active after the LED installation. Activate hazards for at least 20 seconds (or to a count of 12 flashes). After 12 flashes of the Hazards the setting is updated in the BCM.
3. Turn the ignition key switch to IGNITION, but do not start the vehicle. Test lights and verify turn, brake and run lights operate as expected.
4. See the service manual. Verify that there are no BCM codes. If codes display, see the service manual. Follow procedure for clearing BCM codes.
SERVICE PARTS
Figure 3. Service Parts: Custom Touring Front Bullet Turn Signal
Table 1. Service Parts Table
Item
Description (Quantity)
Part Number
1
Seal pin (2)
5118
2
Bracket, mounting, RH turn signal (black)
67800630
3
Bracket, mounting, LH turn signal (black)
12700132
4
Turn signal, Front, (black) (2)
67800987