DETACHABLE KING-SIZE WINDSHIELD FOR SOFTAIL MODELS WITH CHROME NACELLE OR STREET STALKER NACELLE (WITHOUT PASSING LAMPS)
J014202017-08-22
GENERAL
Kit Number
58653-97A: Low profile, smoked windshield
58652-97A: Standard height, clear windshield
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
These windshield kits fit are designed for Softail models that have Chrome Headlight Nacelle Kit (67907-96) or Street Stalker Headlight Nacelle Kit (57910-98B) installed.
Additional Parts Required
NOTE
A service manual for your model motorcycle is available from a Harley-Davidson Dealer.
INSTALLATION
WARNINGRider and passenger safety depend upon the correct installation of this kit.
If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation.
Improper installation of this kit could result in death or serious injury. (00308b)
- Remove upper screws that attach the chrome headlamp nacelle to the front forks.
- See Figure 1. Attach upper docking bushings (22) using washer (21) and mushroom head screws (20). Apply LOCTITE 242 MEDIUM STRENGTH THREADLOCKER ADHESIVE (BLUE) (Loctite 242) on screw threads. Tighten. 25.8 N·m (19 ft-lbs)
- Remove lower screws that attach the chrome headlamp nacelle to the front forks.
- Vehicles equipped with Chrome headlamp nacelle, attach lower docking bushing (22) using washer (21) and button head screw (23). Vehicles equipped with Street Stalker headlamp nacelle, attach lower docking bushing (22) using washer (21) and button head screw (24).
INSTALLING/REMOVING THE WINDSHIELD
NOTE
Inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed.
NOTE
Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of components.
- Carefully lock bottom windshield assembly jaws into the grooves of the rubber docking bushings.
- Hook top windshield assembly jaws into the grooves of the rubber docking bushings.
- Firmly press the windshield into place until it is seated on the docking bushings.
- To remove windshield, grab windshield edges on each side of the center brace and firmly pull the windshield loose from the docking bushings.
CARE AND CLEANING
NOTE
Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections.
NOTICE
Use only Harley-Davidson recommended products on Harley-Davidson windshields. Do not use harsh chemicals or rain sheeting products, which can cause windshield surface damage, such as dulling or hazing. (00231c)
Do not clean polycarbonate in hot sun or high temperature. Powdered, abrasive or alkaline cleanser will damage the windshield. Never scrape the windshield with a razor blade or other sharp instruments because permanent damage will result.
NOTE
Covering the windshield with a clean, wet cloth for about 15 minutes before washing will make dried bug removal easier.
Harley-Davidson Windshield Water Repellent Treatment Part Number 99841-01 is approved for use on Harley-Davidson windshields.
SERVICE PARTS
Figure 1. Service Parts: Windshield Kits
Table 1. Service Parts
Item | Description (Quantity) | Part No. | Item | Description (Quantity) | Part No. | |
|---|---|---|---|---|---|---|
1 | Replacement Windshield Standard Standard Height, Clear Low Profile, Smoked | 58657-97A 58658-97A | 14 | Brace, LH | 58408-75A | |
2 | Screw, panhead, Torx (2) | 2452 | 15 | Windshield brace tape (2) | 58417-77 | |
3 | Screw, panhead, Torx (7) | 2921A | 16 | Washer (9) | 7073 | |
4 | Windshield brace, Inner | 58431-94 | 17 | Acorn nut (9) | 7651 | |
5 | Windshield brace, Outer | 58428-94 | 18 | Acorn nut, 1/4-20 in. (2) | 94004-90T | |
6 | Windshield brace tape (2) | 58416-77A | 19 | Washer, flat, 1/4 in. (4) | 94065-90T | |
7 | Windshield bracket, LH | 58293-95 | Hardware (consisting of items 20 through 24) | |||
8 | Windshield bracket, RH | 58300-95 | 20 | Screw, mushroom head (4) | 58268-95 | |
9 | Screws, buttonhead (2) | 94426-95 | 21 | Washer, chrome (4) | 94066-90T | |
10 | Windshield Retainer, LH | 58259-95 | 22 | Bushing (4) | 67621-94 | |
11 | Windshield Retainer, RH | 58266-95 | 23 | Screw, button head 5/16 x 24 x 1-1/4 in. (2) | 94421-95T | |
12 | Nylon Bushings (4) | 58272-95 | 24 | Screw, button head 5/16 x 24 x 1 in. (2) | 94398-92T | |
13 | Brace, RH | 58406-75A | A | Nacelle | ||