0/0
SOFTAIL REAR SADDLEBAG GUARDS
J066142018-08-20
GENERAL
Kit Number
90201312, 90201315
Models
For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Installation Requirements
LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer.
Kit Contents
See Figure 3 and Table 1.
INSTALLATION
  1. Remove passenger footpeg or passenger footboard assembly (including footboard mount) from vehicle if equipped.
  2. Figure 1 Remove screw (1) and washer (2) from indicated position on rear fender support.
  3. Discard screw (1) and save washer (2) for later use. This location is where the upper part of the saddlebag guard will mount.
    1Rear fender support screw
    2Rear fender support washer
    Figure 1. Hardware Removal
  4. Figure 2 Position saddlebag guard top flange (5) with Original Equipment (OE) washer (2) removed earlier between the flange and rear fender support (3).
  5. Figure 3 Install screw (3) and washer (4). Finger tighten only.
  6. Figure 2 Position bottom flange (6) of saddlebag guard (4) against vehicle frame (7) at location where passenger footpeg (2) (or passenger footboard bolt) attaches.
  7. Figure 3 Determine your model application and follow the applicable installation procedure below:
  1. Apply two drops of threadlocker to the clean threads of screw before installation.
    2. LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97)
    On models with passenger footpeg:
  1. Install socket head cap screw (6) through footpeg support (A) and guard flange into frame, aligning notch on footpeg support with tab on saddlebag guard.
  2. Secure support bolt. Tighten.
    3. 52–64 N·m (38–47 ft-lbs)
  3. Ensure footpeg support is flat against saddlebag guard flange after tightening.
  4. Install footpeg (B). See service manual.
    On models without passenger footpegs:
  1. Install button head screw (5) and washer (4) through guard, flange and into frame. Tighten.
    2. 57–62 N·m (42–46 ft-lbs)
    On models with accessory passenger footboards:
  1. Follow installation instructions of footboard mount kit.
  2. Guard flange mounts between footboard mount and frame. Use specified screws included in footboard mount kit.
  3. Ensure footpeg support is flat against saddlebag guard flange after tightening.
    1Saddlebag
    2Passenger footpeg
    3Rear fender support
    4Saddlebag guard
    5Saddlebag guard top flange
    6Saddlebag guard bottom flange
    7Vehicle frame member
    Figure 2. Rear saddlebag Guard Installed-Right Side
  1. Figure 1 Torque screw that secures saddlebag guard top flange (see step 4). Tighten.
    2. 57–62 N·m (42–46 ft-lbs)
  2. Repeat steps 1-9 for installing saddlebag guard on opposite side of vehicle.
  3. Discard remaining original and kit mounting hardware.
SERVICE PARTS
Figure 3. Service Parts: Softail Rear Saddlebag Guard
Table 1. Service Parts Table
Item
Description (Quantity)
Part Number
1
Saddlebag Guard, left, Chrome
Saddlebag Guard, left, Black
90201313
90201316
2
Saddlebag Guard, right, Chrome
Saddlebag Guard, right, Black
90201314
90201317
3
Screw, button head, Torx, 3/8-16 x 2.25 inch (2)
10200745
4
Washer (4)
10300116
5
Screw, button head, Torx, 3/8-16 x 1.5 inch (2)
3056
6
Screw, socket head, Torx, 3/8-16 x 3.5 inch (2)
4315
Items mentioned in text, but not included in kit:
A
Footpeg support (2)
B
Footpeg (2)