RIDER BACKREST MOUNTING HARDWARE KIT
J067292024-01-22
GENERAL INFORMATION
Table 1. General Information
Kits
Suggested Tools
Skill Level(1)
52300642
Safety Glasses, isopropyl alcohol
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Mounting Hardware Kit
Table 2. Kit Contents: Kit Contents: Mounting Hardware Kit
Verify that all contents are present in the kit before installing or removing items from vehicle.
Item
Qty
Description
Part No.
Notes
1
1
Backrest mounting bracket
52567-93D
2
1
Support bracket
52585-09
3
1
Bolt, 5/16-18 x 5/8 inch
3546
4
1
Front mounting bracket
52590-09
5
1
Flange nut
7716
6
1
Flange screw
3574
7
1
Locking flange nut
7531
8
2
Flange screw
3921
9
2
Flange screw
3574
10
2
Flange nut
7716
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
PREPARE
1. Remove seat. See Service Manual.
2. Handrail models: See Figure 2. Leaving handrail assembly (2) in place, remove handrail screws (1) and discard hardware.
3. Grab strap models: Remove grab strap and discard hardware. See Service Manual.
4. Remove left side cover. See Service Manual.
5. Remove battery. See Service Manual.
6. 2009 - 2018 models: Remove Bank Angle Sensor (BAS) bracket screws (3) and discard hardware.
1Handrail screw (2)
2Handrail assembly
3BAS bracket screw (2)
4BAS bracket
Figure 2. Remove BAS Screws
INSTALL
NOTE
Only use the specified screw to install the front mounting bracket to the BAS bracket.
1. See Figure 3. Install front mounting bracket (7).
a. 2009 - 2018 models: Holding the BAS bracket in place, install the front mounting bracket (7) using flange screws (8). Tighten.
Torque: 8.1–12.2 N·m (72–108 in-lbs)
b. 2019 - Present models: Install front mounting bracket (7) using flange screws (8) and flange nuts (6). Tighten.
Torque: 8.1–12.2 N·m (72–108 in-lbs)
2. Install the backrest mounting bracket (3).
NOTE
It may take a few adjustments to meet riders comfort when installing the backrest mounting bracket.
a. Handrail models: With the backrest mounting bracket in place use the flange screws (1) to install. Tighten.
Torque: 7–11 N·m (62–97 in-lbs)
b. Grab strap models: With the backrest mounting bracket in place, position the grab strap and using the flange screws (1) to install both mounting bracket and grab strap. Tighten.
Torque: 7–11 N·m (62–97 in-lbs)
3. See Figure 1. Install support bracket (2).
a. Position the support bracket on backrest mounting bracket and the front mounting bracket.
b. Using bolt (3) and the locking flange nut (7) loosely install the support bracket on the backrest mounting bracket.
c. Using flange screw (6) and flange nut (5) install the support bracket on the support bracket. Tighten.
Torque: 8.1 N·m (71.7 in-lbs)
d. Tighten bolt (3) and locking flange nut (7).
Torque: 20.3 N·m (15.0 ft-lbs)
1Flange screw (P/N 3574) (2)
2Grab strap (if equipped)
3Backrest mounting bracket
4Handrail (if equipped)
5BAS bracket (2009 - 2018)
6Flange nut (2019 - present)
7Front mounting bracket
8Flange screw (P/N 3921) (2)
Figure 3. Install Backrest Mounting Base
COMPLETE
1. Install battery. See Service Manual.
2. Install left side cover. See Service Manual.
3. Install seat. See Service Manual.
4. Install backrest. See Service Manual.