DYNA GLIDE ADJUSTABLE HIGHWAY PEG MOUNTING KIT
J011752020-09-22
GENERAL
Kit Number
49002-98
Models
This kit is designed for installation on 1991 and later Dyna Glide model motorcycles (except FXDWG models).
Installation Requirements
NOTE
This kit cannot be used with a front engine guard installed.
INSTALLATION
| 1. | See Figure 1. Install setscrew (14) into lower hole on frame tube boss (2) leaving .20 in. of setscrew (or three threads) exposed. | |
| 2. | Place highway peg mounting plate (1) into position. For a lower peg position, place bottom hidden hole in mounting plate over setscrew. For a higher peg position, place upper hidden hole in mounting plate over setscrew. Attach mounting plate to frame tube boss using 1 in. long screw (3), lockwasher (4), and flat washer (5) from kit. Tighten. Torque: 45 N·m (33 ft-lbs) Screws | |
| 3. | Install footrest support (6) onto highway peg support plate using hex nut (7), lockwasher (8) and flat washer (9) from kit. Tighten. Torque: 64 N·m (47 ft-lbs) Nut (7) | |
| 4. | Locate spring washer (10) from kit. While holding spring washer in position on inside of footrest support (with square edge towards motorcycle), position footpeg (not included with this mounting kit) between footrest support mounting tabs, as shown. | |
| 5. | Insert 1-1/2 in. long screw (12) from kit through footrest support mounting tabs, footpeg, and spring washer. Secure using locknut (13) from kit. | |
| 6. | Repeat these steps for the other side of vehicle. |
WARNINGFootrests must fold up and toward rear of motorcycle if struck. Failure to set footrests to fold up and back could result in death or serious injury. (00366a)
| 1 | Mounting plate |
| 2 | Frame tube boss |
| 3 | Screw, 3/8-16 x 1 in. |
| 4 | Lockwasher, 3/8 |
| 5 | Flat washer, 3/8 |
| 6 | Footrest support |
| 7 | Nut, hex, 1/2 |
| 8 | Lockwasher, 1/2 |
| 9 | Flat washer, 1/2 |
| 10 | Spring washer |
| 11 | Footpeg (not included with kit) |
| 12 | Screw, 3/8-16 x 1-1/2 |
| 13 | Locknut, 3/8-16 x 9/16 |
| 14 | Setscrew |
Figure 1. Footpeg and Footpeg Mounting Kit Installation (Right Side of Vehicle)
SERVICE PARTS
Figure 2. Service Parts: Dyna Glide Adjustable Highway
Footpeg Mounting Kit
Table 1. Service Parts
Item | Description | Quantity | Part No. |
|---|---|---|---|
1 | RH Mounting plate | 1 | 49175-98 |
2 | LH Mounting plate | 1 | 49233-98 |
3 | Footrest supports | 1 | 49714-98 |
4 | Nuts | 2 | 7880 |
5 | Lockwashers | 2 | 7068 |
6 | Flat washers | 2 | 6718 |
7 | Screws | 2 | 4721 |
8 | Spring washers | 2 | 50912-72 |
9 | Locknuts | 2 | 7778 |
10 | Screws | 2 | 2879W |
11 | Lockwashers | 2 | 7038 |
12 | Flat washers | 2 | 6701 |
13 | Setscrews | 2 | 3289 |