SOFTAIL FORWARD CONTROLS KIT BLACK
941000022019-10-10
GENERAL
Kit Number
50700060
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
WARNING
Brakes are a critical safety component. Contact a Harley-Davidson dealer for brake repair or replacement. Improperly serviced brakes can adversely affect brake performance, which could result in death or serious injury. (00054a)
Kit Contents
LEFT SIDE
Disassemble Left Side
1. See Figure 6. Remove footpeg from foot support bracket. Retain footpeg, E-clip, clevis pin, and torsion spring for later use.
a. Remove E-clip (3).

Special Tool: E-CLIP TOOL (HD-52369)

NOTE
When removing E-clip, use E-clip tool to prevent damage to painted surfaces.
b. Remove clevis pin (1).
c. Remove footpeg (4).
d. Remove torsion spring (2).
2. See Figure 1. Remove the left mid foot support bracket (3).
a. Remove screws (2).
b. Remove foot support bracket.
3. Remove and discard plastic plug (1) if present.
4. See Figure 2. Remove shifter assembly.
a. Remove screw (5) to free shifter rod (4) from rear shifter rod lever (3).
b. Remove pinch screw (1) from front shifter rod lever (2).
c. Pull foot shift lever (6) and shaft (8) outward until front shifter rod lever (2) is free.
d. Remove front shifter rod lever and shifter rod.
e. Remove foot shift lever, shaft and spacer (8).
1Plastic plug
2Screw (2)
3Left mid foot support bracket
Figure 1. Left Mid Foot Support Bracket
1Pinch screw
2Shifter rod lever, front
3Shifter rod lever, rear
4Shifter rod
5Screw
6Foot shift lever
7Spacer
8Shaft
Figure 2. Shift Linkage: Mid-Mount Foot Control Models
Pre-Assemble Left Side Kit Components
1. See Figure 3. Install footpeg to foot support bracket.
a. Insert short leg of torsion spring (3) into hole in footpeg (1).
b. Insert long leg of torsion spring into hole in left foot support bracket (10).
c. Rotate footpeg into position and install clevis pin (2).
d. Install E-clip (14).

Special Tool: E-CLIP TOOL (HD-52369)

NOTE
When installing E-clip, use E-clip tool to prevent damage to painted surfaces.
2. Install shifter assembly to foot support bracket.
a. Install first small O-ring (11) onto shaft of shift rod lever (9).
b. Install shift rod lever through hole in left foot support bracket (10).
c. Install second small O-ring (11) onto shaft of shift rod lever.
d. Install nylon washer (5) onto shaft of shift rod lever.
e. See Figure 4. Align shift lever with shift rod lever at an angle of 65–75°.
f. See Figure 3. Install shift lever (4) onto shift rod lever.
g. Install lock washer (12) and screw (13). Tighten.
Torque: 24.4–29.8 N·m (18–22 ft-lbs) Shift lever pinch screw
h. Install shifter linkage rod (8) to shift rod lever (9).
i. Install screw (6) and nut (7). Tighten.
Torque: 13.5–19 N·m (120–170 in-lbs) Shifter rod screw
1Left footpeg
2Footpeg clevis pin
3Footpeg torsion spring
4Shift lever sub-assembly
5Nylon washer
6Screw
7Nut
8Shifter linkage rod
9Shift rod lever
10Left foot support bracket
11O-ring - small (2)
12Lock washer
13Screw
14E-clip
Figure 3. Left Side Pre-Assemble
Figure 4. Shift lever assembly angle
Installation Left Side
1. Install left foot support assembly.
a. See Figure 11. Select left foot support bracket assembly and screws (12) from kit.
c. Install left foot support assembly (5).
d. Install screws (6). Tighten.
Torque: 54–61 N·m (40–45 ft-lbs) Left-hand foot support screws
2. Install plug (4) into shifter shaft hole in primary cover.
3. Install shifter linkage.
a. Install shifter linkage rod (1) to rear shifter rod lever (3) with screw (2). Tighten.
Torque: 13.5–19 N·m (120–170 in-lbs) Shifter rod screw
b. Adjust shifter rod ends (7) for rider posture and tighten jam nuts (8).
Torque: 9–13.5 N·m (80–120 in-lbs) Shifter rod jam nuts
1Shifter linkage rod
2Screw
3Shifter rod lever, rear
4Primary cover plug
5Left foot support assembly
6Screw (2)
7Shifter rod end (2)
8Jam nut (2)
Figure 5. Left side forward controls
RIGHT SIDE
Disassemble Right Side
1. See Figure 6. Remove footpeg from foot support bracket. Retain footpeg, E-clip, clevis pin, and torsion spring for later use.
NOTE
When removing E-clip, use E-clip tool to prevent damage to painted surfaces.
a. Remove E-clip (3).

Special Tool: E-CLIP TOOL (HD-52369)

b. Remove clevis pin (1).
c. Remove footpeg (4).
d. Remove torsion spring (2).
2. See Figure 7. Remove right side foot support bracket.
a. Remove front linkage screw (2).
b. Remove screws (7).
c. Remove foot support bracket (1).
3. Remove rear master cylinder from bracket.
a. See Figure 8. Remove cotter circle (1).
b. Remove clevis pin (2).
c. See Figure 7. Remove screws (4).
d. Support rear brake master cylinder (3).
4. Remove brake pedal bracket.
a. Remove screw (5).
b. Remove brake pedal bracket (6).
1Clevis pin
2Torsion spring
3E-clip
4Footpeg
Figure 6. Rider Footpeg (Typical)
1Foot support bracket
2Front linkage screw
3Rear brake master cylinder
4Master cylinder screw (2)
5Brake pedal bracket screw
6Brake pedal bracket
7Screw (2)
Figure 7. Right Side Mid Controls
1Cotter circle
2Clevis pin
Figure 8. Rear Master Cylinder - Rear View: (exhaust remove for clarity)
Pre-Assemble Right Side Kit Components
1. See Figure 9. Install footpeg to foot support bracket.
a. Insert short leg of torsion spring (4) into hole in footpeg (6).
b. Insert long leg of torsion spring into hole in right foot support bracket (3).
c. Rotate footpeg into position and install clevis pin (5).
d. Install E-clip (7).

Special Tool: E-CLIP TOOL (HD-52369)

NOTE
When installing E-clip, use E-clip tool to prevent damage to painted surfaces.
2. Assemble brake pedal.
a. Install first large O-ring (10) onto brake pedal mounting bracket (1).
b. Install brake pedal (2) onto mounting bracket.
c. Install second large O-ring (10) onto brake pedal mounting bracket.
d. Install screw (8) and large washer (9).
e. Install small washer (11) and nut (12). Tighten.
Torque: 24.4–29.8 N·m (18–22 ft-lbs) Brake pedal pivot screw
1Brake pedal bracket
2Brake pedal - Black
3Right foot support bracket
4Footpeg torsion spring
5Footpeg clevis pin
6Right footpeg
7E-clip
8Screw
9Washer - large
10O-ring - large (2)
11Washer - small
12Nut
Figure 9. Right Side Pre-Assemble
Installation Right Side
1. See Figure 11. Select the brake pedal bracket assembly and screw (23) from kit.
2. See Figure 10 Install brake pedal mounting bracket.
b. Install brake pedal bracket (1).
c. Install screw (2). Hand tighten.
3. Install rear master cylinder to brake pedal mounting bracket.
a. Install rear master cylinder (5).
NOTE
Verify that the brake pedal link is between the master cylinder yoke when placing the master cylinder into place.
b. See Figure 8. Install clevis pin (2).
c. Install cotter circle (1).
d. See Figure 10. Install screws (4). Tighten.
Torque: 24–30 N·m (18–22 ft-lbs) Rear master cylinder mounting screws
4. Install right foot support assembly.
a. See Figure 11. Select right foot support bracket assembly and screws (9) from kit.
c. Install right foot support assembly (6).
d. Install screws (3).
e. Tighten screws (2 and 3).
Torque: 54–61 N·m (40–45 ft-lbs) Right foot support screws
1Brake pedal bracket
2Brake pedal bracket screw
3Foot support bracket screw (2)
4Master cylinder screw (2)
5Rear master cylinder
6Right foot support assembly
Figure 10. Right Foot Support Bracket
Service Parts
Figure 11. Service Parts: Forward Controls Kit - Black
Table 1. Service Parts
Item
Bag(1)
Description (Quantity)
Part Number
Item
Bag(1)
Description (Quantity)
Part Number
1
A
Shift lever sub-assembly
33600211
13
B
Washer - small
6702
2
A
Nylon washer
6057
14
B
Flange nut
7531
3
A
O-ring - small (2)
11191
15
B
Cotter circle
51938-04
4
A
Socket head button screw (2)
4387
16
B
Rear brake clevis pin
42460-80B
5
A
Lock nut
7727
17
B
Screw (2)
10500022
6
A
Shifter linkage rod
33600123
18
B
Brake pedal - Black
50600329
7
A
Shift rod lever
33600132
19
B
Right foot support bracket
50500746
8
A
Left foot support bracket
33600134
20
B
Button head torx screw 2.25 inch
10200851
9
C
Cap screw, button head, 3/8-16 X 1.62 inch (4)
10200536
21
B
Washer
6237
10
A
Lock washer
7041
22
B
O-Ring - large (2)
11364
11
A
Hex head screw
4017
23
B
Cap screw, button head, 3/8-16 X 1 inch
4512A
12
A
Primary cover plug
25701148
24
B
Brake pedal bracket
50600206
Items mentioned in text, but not included in kit:
A
Left footpeg
50501107
D
E-clip (2)
50500701
B
Footpeg clevis pin (2)
50500702
E
Right footpeg
50501106
C
Footpeg torsion spring (2)
50500703
(1) The contents of bag A will be used for left side assemblies, bag B will be used for right side assemblies and bag C will be used for both left and right sides.