TOUR-PAK SIDE MARKER LIGHT KIT- SMOKED
941000212021-08-20
GENERAL
Kit Number
68000312 (Smoke), 68000313 (Red)
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Additional Parts Required
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
INSTALLATION
WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a)
WARNINGDisconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a)
| 1. | Disconnect negative battery cable or remove main fuse. | |||||||||
| 2. | Remove all contents from Tour-Pak®. | |||||||||
| 3. | Remove Tour-Pak from motorcycle. Refer to the appropriate service manual for Tour-Pak removal. | |||||||||
| 4. | 2014 and later follow service manual to remove existing side marker lights and reverse for installation of this kit. | 
Figure 1. Metal Plate | ||||||||
| 5. | See Figure 1. Remove metal plate from bottom of Tour-Pak by removing six flange nuts underneath Tour-Pak. Retain plate and nuts for later use. | 
Figure 2. Removable Chrome Strip | ||||||||
| 6. | See Figure 2. Remove chrome strips from Tour-Pak by removing two T15 TORX® screws. Retain screws for later use. | 
Figure 3. Tour-Pak Crosshairs Location | ||||||||
| 7. | See Figure 3. Locate crosshairs imprinted on side of Tour-Pak. Drill a 0.50 in (12.7 mm) hole at crosshairs location. Repeat for opposite side. | 
Figure 4. Wire Harness Routing | ||||||||
| 8. | See Figure 4. Place light housings into position and feed cords through 0.50 in (12.7 mm) hole. | |||||||||
| 9. | Install light assemblies by aligning holes in Tour-Pak with threaded bosses in light housings using two T15 TORX® screws (4) removed earlier. | |||||||||
| 10. | Install plastic grommet (3) on light wire and push into 0.50 in (12.7 mm) hole. | |||||||||
| 11. | Figure 6 Install connector housings (3) onto lamp terminal using wire harness (6). a. Match terminals, black to black and blue to blue on harness. | |||||||||
| 12. | Place wire harness (1) in bottom of Tour-Pak and arrange as seen in Figure 4. Use adhesive-backed clips (2) to retain harness in position. NOTE If conduit and connectors are not captured in channel at bottom of Tour-Pak, installation of metal floor plate can pinch wires or damage connectors. | |||||||||
| 13. | Install metal plate in bottom of Tour-Pak using six flange nuts removed earlier. Tighten. See Figure 1. Torque: 4.5–6.8 N·m (40–60 in-lbs) flange nuts | |||||||||
| 14. | Install Tour-Pak. See proper service manual for Tour-Pak installation procedure. | 
Figure 5. Antenna Cable and Connector | ||||||||
| 15. | See Figure 5. Connect Tour-Pak light harness connector to unused connector bundled with antenna cable inside of Tour-Pak. | |||||||||
| 16. | Connect negative battery cable or main fuse. |
WARNINGBe sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a)
SERVICE PARTS
Figure 6. Service Parts: Tour-Pak Side Marker Light Kit
Table 1. Service Parts: Tour-Pak Side Marker Light Kit
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Sidemarker sub-assembly, left, smoke | Not Sold Separately | |
| 1 | Sidemarker sub-assembly, left, red | Not Sold Separately | ||
| 2 | 1 | Sidemarker sub-assembly, right, smoke | Not Sold Separately | |
| 1 | Sidemarker sub-assembly, right, red | Not Sold Separately | ||
| 3 | 2 | Housing, 2-way | 73152-96BK | |
| 4 | 2 | Grommet | 57978-00 | |
| 5 | 6 | Clip | 10102 | |
| 6 | 1 | Wire harness | 70650-06 | |