SHIFT SIDE MID-CONTROL
941001192021-01-12
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) | Time |
|---|---|---|---|
50502041 | Safety Glasses, Torque Wrench, E-CLIP TOOL (Part Number:HD-52369) |  | 1 hour |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Mid-Control Kit - Shift Side
Table 2. Kit Contents: Mid-Control Kit - Shift Side
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Mid control, shift linkage rod assembly | 33600343 | |
| 2 | 1 | Mid control, lever assembly kit | 33900254 | |
| 3 | 1 | Mid control, footpeg mounting bracket, left | 50502076 | Includes bushing (11000193) |
| 4 | 1 | Screw | 4387 | |
| 5 | 1 | Plug | 10040 | |
| 6 | 2 | Screw | 10200536 | |
| 7 | 2 | Screw | 10201074 | FXDRS only |
| 8 | 1 | Washer | 10300232 | |
| 9 | 1 | Retaining ring, clip | 12200230 | |
| 10 | 1 | Spacer, footpeg mounting bracket | 50502089 | FXDRS only |
| 11 | 1 | Stud, peg | 34591-08 | |
| 12 | 1 | Rubber, toe peg, shifter | 33600156 | |
| 13 | 2 | Washer, nylon | 10300254 | |
Figure 2. Service Kit: Lever Assembly
Table 3. Service Kit: Lever Assembly - Shift Side
| Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
| 1 | 1 | Mid control shift lever | Not sold separately | |
| 2 | 2 | Washer | 6703 | |
| 3 | 2 | Screw | 942 | |
| 4 | 1 | Shift lever arm | Not sold separately | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
PREPARE
| 1. | Set vehicle upright. See service manual. |
REMOVE
| 1. | See Figure 4. Remove footpeg. a. Remove E-clip (2). Special Tool: E-CLIP TOOL (HD-52369) NOTE When removing E-clip, use E-clip tool to help prevent damage to painted surfaces. b. Remove clevis pin (5). c. Remove footpeg (3). d. Remove torsion spring (4). | |
| 2. | See Figure 3. Remove foot support bracket. a. Remove screws (2). b. Remove foot support bracket (1). | |
| 3. | Disconnect shifter connecting rod from transmission. |
| 1 | Foot support bracket |
| 2 | Screw (2) |
Figure 3. Left Foot Support Bracket (Typical)
| 1 | O-ring (2) |
| 2 | E-clip |
| 3 | Footpeg |
| 4 | Torsion spring |
| 5 | Clevis Pin |
| 6 | Foot support bracket |
| 7 | Wear Peg |
Figure 4. Left Side Footpeg (Typical)
INSTALL
| 1. | See Figure 5. Assemble shift lever assembly. a. Install shift lever arm (1) to shift lever mid control (2) with screws (3) and washers (4). | |
| 2. | See Figure 1. Install shift lever assembly (2) to footpeg mounting bracket (3) with two nylon washers (13), washer (8) and retaining ring (9). | |
| 3. | See Figure 1. Install shift linkage rod assembly (1) to shift lever assembly (2) with screw (4). Tighten. Torque: 13.6–19 N·m (10–14 ft-lbs) | |
| 4. | Install assembly to vehicle with screws (6) except for FXDRS models. Tighten. Torque: 54.2–61 N·m (40–45 ft-lbs) | |
| 5. | For FXDRS models: Install assembly to vehicle with screws (7) and spacer (10). Tighten. Torque: 54.2–61 N·m (40–45 ft-lbs) | |
| 6. | Connect shift linkage assembly (1) to transmission using screw removed earlier. Tighten. Torque: 13.6–19 N·m (10–14 ft-lbs) | |
| 7. | See Figure 6. Install toe peg (1) and screw (4). Tighten. Torque: 10.8–16.2 N·m (8–12 ft-lbs) | |
| 8. | See Figure 6. Install plug (5) into empty hole in vehicle frame. | |
| 9. | See Figure 4. Install footpeg removed earlier. a. Insert short leg of torsion spring (4) into hole in footpeg (3). b. Insert long leg of torsion spring (4) into hole in foot support bracket (6). c. Rotate footpeg into position. d. Install clevis pin (5). e. Install E-clip (2). Special Tool: E-CLIP TOOL (HD-52369) NOTE When installing E-clip, use E-clip tool to help prevent damage to painted surfaces. | |
| 10. | See Figure 5. Adjust toe peg height by moving slotted lever of shift lever assembly (1). | |
| 11. | Tighten screws (3). Torque: 9.5–13.6 N·m (7–10 ft-lbs) |
| 1 | Shift lever arm |
| 2 | Mid-control shift lever |
| 3 | Screw (2) |
| 4 | Washer (2) |
Figure 5. Mid-Control Shift Lever Assembly
| 1 | Toe peg |
| 2 | Mid-control shift lever Assembly |
| 3 | Footpeg |
| 4 | Screw, toe peg |
| 5 | Plug |
Figure 6. Mid-Control Installed
COMPLETE
| 1. | Remove vehicle from upright. See service manual. |