Kits | Suggested Tools | Skill Level(1) | Time |
---|---|---|---|
69202757 | Digital Technician II (DT II), Safety glasses, Sockets, Wrenches, Cutters, Torque wrench | 6 hours |
Item | Qty | Description | Part No. | Notes | |
---|---|---|---|---|---|
1 | 1 | LED Projector bank cornering lamp | 67700517 | ||
2 | 14 | Cable strap | 10065 | ||
3 | 1 | Body control module (BCM) | 41000674 | ||
4 | 1 | Wire harness | 69202744 | ||
2 | Round cable ferrite core | 69202973 | Service component for 69202744 | ||
5 | 1 | Ground strap | 69202535 | ||
6 | 2 | Screw, button head | 10200924 |
1. | Remove main fuse. See service manual. | |
2. | Remove front and rear seat. See service manual. | |
3. | Remove fuel tank. See service manual. | |
4. | Remove airbox assembly. See service manual. a. To prevent debris from entering the engine, cover fuel induction module. | |
5. | Remove left front electrical caddy cover. See service manual. | |
6. | Remove fairing. See service manual. | |
7. | Remove cowl. See service manual. |
1. | Remove Body Control Module (BCM). See service manual. | |
2. | See Figure 3. Remove cowl cover. a. Remove screws (1). b. Remove and discard cowl cover (2). |
1. | See Figure 2. Install new BCM (4). See service manual. | |
2. | See Figure 4. Install ground strap (1). | |
3. | Install screws (2). Tighten. Torque: 8–10 N·m (71–89 in-lbs) Ground strap screw | |
4. | See Figure 5. Install cornering lamp (3). | |
5. | Install screws (1). Tighten. Torque: 8–10 N·m (71–89 in-lbs) Cornering lamp screw | |
6. | See Figure 2. Remove plug (2) from P&A connector (1). | |
7. | See Figure 6. Install LED adaptive headlamp harness: a. Connect [325A] to vehicle P&A connector. b. Connect [C242B-C] to vehicle BCM. | |
8. | Route harness and headlamp connector (3) along with the main harness on the inside of the left frame rail toward the headlamp. a. Exit through left front electrical caddy cover area. b. Follow routing of existing harness to headlamp. | |
9. | See Figure 6. Connect cornering lamp connector (3). | |
10. | Secure with cable straps as needed. | |
11. | Ensure dynamic movement of harnessing and other parts behind the lamp will not be restricted by moving handlebars from fork lock left to fork lock right. |
1 | P&A Connector |
2 | Plug |
3 | [C242B-C] BCM Connector |
4 | BCM |
1 | Screw (2) |
2 | Cowl cover |
1 | Ground strap |
2 | Screw (2) |
1 | Screw (2) |
2 | Cornering lamp connector |
3 | Cornering lamp |
1 | [325A] P&A Connector |
2 | [C242B-C] BCM Connector |
3 | [C143B] Cornering lamp connector |
1. | Configure new Body Control Module BCM using special tool. Special Tool: DIGITAL TECHNICIAN II (HD-48650) a. Select VEHICLE SETUP icon. b. Follow on-screen prompts. | |
2. | Install cowl. See service manual. | |
3. | Install fairing. See service manual. | |
4. | Install left front electrical caddy cover. See service manual. | |
5. | Install airbox assembly. See service manual. | |
6. | Install fuel tank. See service manual. | |
7. | Install front and rear seat. After installing seat, pull up on the seat to verify that it is secure. See service manual. | |
8. | Install main fuse. See service manual. |
1. | Place vehicle in accessory mode. a. See Figure 7. With security fob present, press and hold the TRIP switch (1), release. | |
2. | Access settings menu. a. See Figure 7. Press menu button (2) on Left Hand Control Module (LHCM). b. See Figure 8. Settings menu will display. | |
3. | To check bank angle lighting, navigate to aiming ready menu. SETTINGS > RIDE CUSTOMIZATION > BANK LAMP AIMING > AIMING READY. | |
4. | See Figure 9. If bank angle lights do not align as shown, adjustment is necessary. a. See Figure 10. Loosen bank angle lamp screws. b. See Figure 9. Set vertical adjustment. c. See Figure 10. Tighten screws. Torque: 8–10 N·m (71–89 in-lbs) Bank angle lamp screw |
1. | See Figure 6. Remove connector (3). See Electrical Diagnostic Manual. | |
2. | See Figure 1. Replace round cable ferrite core (4) as needed. | |
3. | Install connector (3). See Electrical Diagnostic Manual. |