BRAKE SIDE MID-CONTROL
941001222021-01-22
GENERAL INFORMATION
Table 1. General Information
Kits | Suggested Tools | Skill Level(1) | Time |
|---|---|---|---|
50501988 | Safety Glasses, Torque Wrench, E-CLIP TOOL (Part Number:HD-52369) |  | 1 hour |
(1) Tightening to torque value or other moderate tools and techniques required
KIT CONTENTS
Figure 1. Kit Contents: Mid-Control - Brake Side
Table 2. Kit Contents: Mid-Control Kit - Brake Side
 | Verify that all contents are present in the kit before installing or removing items from vehicle. | ||||
|---|---|---|---|---|---|
Item | Qty | Description | Part No. | Notes | |
 | 1 | 1 | Footpeg mounting bracket | 50500601 | |
| 2 | 1 | Brake pedal assembly | 50600274 | |
| 3 | 1 | Brake pedal pushrod | 50600262 | |
| 4 | 2 | Screw | 4387 | |
| 5 | 1 | Screw | 10200850 | |
| 6 | 1 | Clevis pin | 42460-80B | |
| 7 | 1 | Cotter circle | 51938-04 | |
| 8 | 1 | Locknut, flange | 7531 | |
| 9 | 1 | Washer | 6702 | |
| 10 | 1 | Master cylinder bracket sub-assembly | 50600288 | |
| 11 | 1 | Screw | 4512A | |
| 12 | 1 | Brake pedal crank assembly | 50600263 | |
| 13 | 1 | Washer | 6333 | |
| 14 | 2 | Screw | 10200536 | |
| 15 | 1 | Washer | 6036 | |
| 16 | 1 | Screw | 1001 | |
GENERAL
Models
For model fitment information, see the Parts and Accessories (P&A) Retail Catalog or the Parts and Accessories section of www.harley-davidson.com.
Verify that the most current version of the instruction sheet is used. It is available at: h-d.com/isheets
Contact Harley-Davidson Customer Support Center at 1-800-258-2464 (U.S. only) or 1-414-343-4056.
Installation Requirements
This kit requires the installation of P&A Exhaust Kit (64900828 or 64900829).
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet references service manual information. A service manual for the year and model motorcycle is required for this installation and is available from:
- A Harley-Davidson dealer.
- H-D Service Information Portal, a subscription-based access available for most 2001 and newer models. For more information see Frequently ask questions about subscriptions.
PREPARE
| 1. | Set vehicle upright. See service manual. |
REMOVE
| 1. | Figure 2 Remove footpeg. a. Remove E-clip (5). Special Tool: E-CLIP TOOL (HD-52369) NOTE When removing E-clip, use E-clip tool to help prevent damage to painted surfaces. b. Remove clevis pin (1). c. Remove footpeg (3). d. Remove torsion spring (2). | |
| 2. | Figure 3 Remove foot support bracket. a. Remove screws (2) b. Remove foot support bracket (1). | |
| 3. | Remove brake pedal. |
| 1 | Clevis pin |
| 2 | Torsion spring |
| 3 | Footpeg |
| 4 | Wear peg |
| 5 | E-clip |
| 6 | Foot support bracket |
Figure 2. Right Side Footpeg (Typical)
| 1 | Foot support bracket |
| 2 | Screw (2) |
Figure 3. Right Foot Support Bracket (Typical)
| 8 | Clevis pin |
Figure 4. Brake Pedal
| 1 | Master cylinder |
| 2 | Screw (2) |
| 3 | Washer (2) |
| 4 | Bracket |
Figure 5. Remove Master Cylinder from Bracket
INSTALL
| 1. | Figure 1 Install brake pedal assembly. a. Install brake pedal assembly (2) to footpeg mounting bracket (1) with washer (15) and screw (16). Tighten. Torque: 13.6–19 N·m (10–14 ft-lbs) b. Install brake pedal crank assembly (12) to brake pedal bracket sub-assembly (10) with washer (13), screw (5), washer (9) and nut (8). c. Install brake pedal pushrod (3) to pedal assembly (2) and brake pedal crank assembly (12) with two screws (4). Tighten. Torque: 20.3–24.4 N·m (15–18 ft-lbs) | |
| 2. | Figure 1 Install master cylinder to master cylinder bracket sub-assembly (10) with Original Equipment (OE) screws and washers removed earlier. Tighten. Torque: 24.4–30 N·m (18–22 ft-lbs) | |
| 3. | Figure 1 Install master cylinder rod to brake pedal crank assembly (12) with clevis pin (6) and cotter circle (7). | |
| 4. | See Figure 1 and Figure 6. Install complete assembly to vehicle with two screws (14) and screw (11). Tighten. Torque: 54.2–61 N·m (40–45 ft-lbs) Torque: 40.8–54.2 N·m (30–40 ft-lbs) | |
| 5. | Figure 2 Install footpeg removed earlier. a. Insert short leg of torsion spring (2) into hole in footpeg (3). b. Insert long leg of torsion spring (2) into hole in foot support bracket (6). c. Rotate footpeg into position and install clevis pin (1). d. Install E-clip (5). Special Tool: E-CLIP TOOL (HD-52369) NOTE When installing E-clip, use E-clip tool to help prevent damage to painted surfaces. |
| 14 | Screws (2) |
| 18 | Screw |
Figure 6. Mid-Control Assembly Installed to Vehicle
COMPLETE
WARNINGAfter repairing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a)
| 1. | Verify operation of brake pedal. | |
| 2. | Remove vehicle from upright. See service manual. |